Skip to content

Remarry Syscon

Chattrapat Sangmanee edited this page Sep 12, 2026 · 15 revisions

Requirements

  • Hardware flasher
  • SC UART (Through modchip)
  • SB UART (Optional)

Hardware flashing

Download qcfw jig zip, then write following files into flash at these offset:

NOR

  • Stagex.bin = 0xF21000
  • Stagex_aux.bin = 0xF30000
  • CoreOS.bin = 0x0C0000
  • CoreOS_2.bin = 0x7C0000

eMMC

  • Stagex.bin = 0xA1000
  • Stagex_aux.bin = 0xB0000
  • CoreOS.bin = 0x0C0020
  • CoreOS_2.bin = 0x7C0010

Then apply syscon command from qcfw_sc_eeprom.txt

Remarry

1. Enable logging (Optional)

  • Send syscon command: w 48c02 2
  • Send syscon command: w 48cf0 3

2. Switch to jig firmware

  • Send syscon command: w f02 1

3. Remarry (first stage)

  • Turn on your console
  • You should see this on your SB UART:
booting ss_init.fself...
ss sdk-4.4.6
ss build date:	Thu Jun 20 00:50:07 JST 2013
ss revision:	5083 
sys revision:	49871 
[INFO]: sc_init START
[INFO]: 1...o
[INFO]: 2 skip
[INFO]: 3...o
[INFO]: 4.0.1...o    4.0.2...o    4.0.3...o    4.0.4...o
[INFO]: 4.1.1...o    4.1.2...o    4.1.3...o    4.1.4...o
[INFO]: pre5...o
[INFO]: skip 5, 6, 7, 8 (0x31)
[INFO]: sc_init SUCCESS
erasing core os in standby bank...
erasing core os in standby bank skipped.

or

booting ss_init.fself...
ss sdk-4.4.6
ss build date:	Thu Jun 20 00:50:07 JST 2013
ss revision:	5083 
sys revision:	49871 
[INFO]: sc_init START
[INFO]: 1...o
[INFO]: 2 skip
[INFO]: 3...o
[INFO]: 4.0.1...o    4.0.2...o    4.0.3...o    4.0.4...o
[INFO]: 4.1.1...o    4.1.2...o    4.1.3...o    4.1.4...o
[INFO]: pre5...o
[INFO]: 5...o
[INFO]: 6...o
[INFO]: 7...o
[INFO]: 8...o (status 0x31)
[INFO]: sc_init SUCCESS
erasing core os in standby bank...
erasing core os in standby bank skipped.

Then ambulance beep and shutdown by itself

It can be different from above, but as long as next step is exact match it is ok.

4. Remarry (second stage)

  • Turn on your console again
  • You should see this on your SB UART:
booting ss_init.fself...
ss sdk-4.4.6
ss build date:	Thu Jun 20 00:50:07 JST 2013
ss revision:	5083 
sys revision:	49871 
[INFO]: sc_init START
[INFO]: 1...o
[INFO]: 2...o
[INFO]: 3...o
[INFO]: 4.0.1...o    4.0.2...o    4.0.3...o    4.0.4...o
[INFO]: 4.1.1...o    4.1.2...o    4.1.3...o    4.1.4...o
[INFO]: pre5...o
[INFO]: skip 5, 6, 7, 8 (0x31)
[INFO]: sc_init SUCCESS
erasing core os in standby bank...
erasing core os in standby bank skipped.

Then ambulance beep and shutdown by itself

5. Switch to normal firmware

  • Send syscon command: w f02 2

6. Exit FSM

  • Send syscon command: w f05 0
  • Turn on your console once to apply, then shutdown manually after a while if it doesn't shutdown by itself

7. Disable logging (Optional)

  • Send syscon command: w 48c02 5
  • Send syscon command: w 48cf0 ff

Turn on your console, enter safe mode then install firmware normally TWICE in a row

After this your console should be fully functional

Clone this wiki locally