Repository navigation
Second release of the floppy3.5 firmware. This one updates the ESP32-S3 bridge only; the RP2354A controller firmware is unchanged from v1.0.0.
What's new
- Fix: the board could switch itself off when a disk read started. This happened when WiFi was busy (the web page open) as the drive motor spun up: the two current peaks together pulled the battery supply down. WiFi transmit power is now capped at 11 dBm while the drive runs. In testing, full power lost power 3 reads out of 3 and the cap lost none out of 3, with the web page fully loaded. To change the setting:
POST /api/wifipwr?mode=0..3(0 full power, 1 capped, 2 radio off during reads, 3 off during spin-up only). - DISP button pages: a short press cycles the LCD through disk, WiFi (QR code, IP, network, signal), battery (%, volts, time left or time to full), SD card (free space, disks saved, last save) and system (firmware, serial, uptime, clock, temperatures, why it last switched off). Long press still turns the LCD off.
- WiFi reset from the buttons: hold SAVE + DISP for 5 s to forget the WiFi network and restart into the Floppy-Setup portal. The LCD counts down; let go to cancel.
- Auto power-off: on battery, the board switches off after 5 minutes with no button press, web page action or drive work. The LCD counts down the last 30 s, and any button keeps it on. An open web page that is only showing status does not keep it on.
- Low battery warning: at 15% the LCD and web page show a low-battery banner, and at 5% a blinking "critical" one.
- Power-loss record:
/api/status→lastoffnow records which drive step was running when power was lost, plus the WiFi state. New status fields:up_s,autooff_s,wifipwr,batt.low.
What's in the zip
| Folder | File | Use |
|---|---|---|
controller-rp2354/ |
gw_rp2354.uf2 |
Install over USB: hold BOOTSEL (S4), connect power, copy the file to the RP2350 drive. Same as v1.0.0. |
controller-rp2354/ |
gw_rp2354.bin |
Update over WiFi from the web page. Same as v1.0.0. |
bridge-esp32s3/ |
flash_args + 4 .bin files |
First install over USB with esptool.py |
bridge-esp32s3/ |
gw_wifi_bridge.bin |
Update over WiFi: Rear panel > SHOW > FIRMWARE UPDATE |
SHA-256 checksums are in SHA256SUMS.txt.
Updating from v1.0.0
Upload bridge-esp32s3/gw_wifi_bridge.bin from the web page (Rear panel > SHOW > FIRMWARE UPDATE). WiFi and settings are kept. The controller doesn't need updating.
First install of the bridge
From inside bridge-esp32s3/:
esptool.py --chip esp32s3 -p <PORT> erase_flash
esptool.py --chip esp32s3 -p <PORT> write_flash @flash_args
Do the first install on USB power. The board does not work fully on battery until the firmware runs and sets the charger limits.
Supported disks
1.44 MB HD disks with FAT12 (for example Sony Mavica disks). Only files in the root folder are shown and copied; folders and hidden files are skipped. 720 KB DD and other formats are not supported.
Known issues
- The bring-up self-test (
firmware/esp32-bringup/) is still not in the release. - The controller uses the default Raspberry Pi USB ID (2E8A:000A), so pass the port to the gw tool:
gw read --device <PORT> ...
Build info
The bridge is built from this tag's source with ESP-IDF 5.2.7 and reports version 1.1.0 on the web page and on the LCD System page. The controller files are unchanged from v1.0.0. Tested on the gen-4 board: installed over WiFi, read a disk with the web page busy, and confirmed the idle auto-off.