Skip to content

Building Rooms

codingncaffeine edited this page Oct 12, 2026 · 2 revisions

Building Rooms

A map is made of rooms (sectors). Each has walls (linedefs) joining corners (vertices), a floor height, a ceiling height and a brightness (light level). Pick Room (R in the WadSmith key preset) and draw.

Drawing a room

  • Rectangle: drag. The corners snap to the grid and to other corners.
  • Any shape: click corner after corner, then double-click the last corner (or click the first corner again) to close the room. Enter finishes the corners as an open line instead, which splits a room when it runs from wall to wall. Backspace takes back the last corner and Esc stops. The status bar, and the Guide's card while a step is open, say this as you draw.
  • Round room: hold Ctrl while you drag. Press [ or ] to use fewer or more sides. Let go of Ctrl for a rectangle again.
  • Against other rooms: it shares their walls and never removes any.

Smart guides line a new corner up with corners nearby, and a side settles on a whole 45 degrees when close. Shift keeps every side to the nearest 15 degrees.

Heights and light

Click a room and use the Inspector. The player steps up 24 at most and needs 56 of headroom.

Setting Presets
Ceiling height Low (96 above the floor, a low room or a corridor), Normal (128), Tall (192, room for a ledge or a window above), Huge (320, a cavern or a courtyard)
Brightness Dark (96, for secrets and scares), Dim (144), Normal (192, well lit), Bright (255, full light)

You can also type numbers. Light colour and Fog colour take a colour such as #FFFFFF. Floor level with and Ceiling level with copy a neighbour's height.

Steps and ramps

When a room joins two floors more than a step (24) apart, its Inspector shows Joins floors and offers:

  • Add steps - cuts the room into stairs, as the Stairs tool makes them.
  • Make a ramp - slopes the floor from the low room to the high one, when it is not too steep.

Floor slopes from and Ceiling slopes from slope any room from one of its walls, with Floor reaches and Ceiling reaches for the height at the far side. Choose Not sloped to flatten it.

Moving, joining and splitting

  • Move: drag a room. Its walls, textures and monsters go with it, and its neighbours stay sealed. Handles round a selection resize it (Ctrl resizes from the middle, Shift goes freely) and a knob turns it. The Inspector also has Turn by, Resize (%) and Mirror buttons.
  • Join: select two or more rooms and press J, or use Join them into one room. The walls between them go.
  • Split: with the Room tool, click on one wall of a room, then on another wall of the same room, and press Enter. The line becomes walls, and the smaller part becomes a room of its own with the same settings.
  • Rooms inside rooms: the Inspector offers Make it a pillar, a pool or a platform.

Symmetry

The Mirror button repeats the rooms you draw and the things you place about a middle, as deathmatch maps are built: left-right, top-bottom, four ways, Half turn or Quarter turns. The middle is the selection's, or the map's; dashed lines show it.

Rounding corners

Select a corner with the Select tool. Under ROUND IT OFF, set Curve reach and Curve sides, then press Round this corner. It is one undo step.

Groups and locks

Select rooms and things and type a name under Group. With nothing selected, the Inspector lists the groups to select, hide or lock. Lock it stops a selection being picked, dragged or reshaped by its neighbours; unlock it with nothing selected.

Copy, paste and prefabs

Ctrl+C, Ctrl+X and Ctrl+V copy, cut and paste rooms and their things, into this map or another. Save as a prefab keeps a selection in the project, under Objects, Prefabs, to drag onto any of its maps.

Looks

On the Textures tab, New rooms look like sets the walls, floor, ceiling and light of new rooms, and of the doors, stairs and switches made in them. Draw new rooms like this one in a room's Inspector takes that room's look.

Clone this wiki locally