amd-xgbe: Move the PHY support into amd-xgbe

The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).

Update the driver version to 1.0.1.

Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Author: tlendacky

Documentation/devicetree/bindings/net/amd-xgbe-phy.txt

@@ -1,6 +1,6 @@
 * AMD 10GbE driver (amd-xgbe)
 
-Required properties:
+Required properties (ethernet device):
 - compatible: Should be "amd,xgbe-seattle-v1a"
 - reg: Address and length of the register sets for the device
    - MAC registers
@@ -22,14 +22,43 @@ Required properties:
 - phy-handle: See ethernet.txt file in the same directory
 - phy-mode: See ethernet.txt file in the same directory
 
-Optional properties:
+Optional properties (ethernet device):
 - mac-address: mac address to be assigned to the device. Can be overridden
   by UEFI.
 - dma-coherent: Present if dma operations are coherent
 - amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate
   a unique interrupt for each DMA channel - this requires an additional
   interrupt be configured for each DMA channel
 
+Required properties (phy device):
+- compatible: Should be "amd,xgbe-phy-seattle-v1a"
+- reg: Address and length of the register sets for the device
+   - SerDes Rx/Tx registers
+   - SerDes integration registers (1/2)
+   - SerDes integration registers (2/2)
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the amd-xgbe-phy interrupt.
+
+Optional properties (phy device):
+- amd,speed-set: Speed capabilities of the device
+    0 - 1GbE and 10GbE (default)
+    1 - 2.5GbE and 10GbE
+
+The following optional properties are represented by an array with each
+value corresponding to a particular speed. The first array value represents
+the setting for the 1GbE speed, the second value for the 2.5GbE speed and
+the third value for the 10GbE speed.  All three values are required if the
+property is used.
+- amd,serdes-blwc: Baseline wandering correction enablement
+    0 - Off
+    1 - On
+- amd,serdes-cdr-rate: CDR rate speed selection
+- amd,serdes-pq-skew: PQ (data sampling) skew
+- amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
+
 Example:
 	xgbe@e0700000 {
 		compatible = "amd,xgbe-seattle-v1a";
@@ -41,7 +70,23 @@ Example:
 		amd,per-channel-interrupt;
 		clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>;
 		clock-names = "dma_clk", "ptp_clk";
-		phy-handle = <&phy>;
+		phy-handle = <&xgbe_phy>;
 		phy-mode = "xgmii";
 		mac-address = [ 02 a1 a2 a3 a4 a5 ];
 	};
+
+	xgbe_phy@e1240800 {
+		compatible = "amd,xgbe-phy-seattle-v1a";
+		reg = <0 0xe1240800 0 0x00400>,
+		      <0 0xe1250000 0 0x00060>,
+		      <0 0xe1250080 0 0x00004>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 323 4>;
+		amd,speed-set = <0>;
+		amd,serdes-blwc = <1>, <1>, <0>;
+		amd,serdes-cdr-rate = <2>, <2>, <7>;
+		amd,serdes-pq-skew = <10>, <10>, <30>;
+		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
+	};

Documentation/devicetree/bindings/net/amd-xgbe.txt

@@ -652,7 +652,6 @@ M:	Tom Lendacky <thomas.lendacky@amd.com>
 L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/amd/xgbe/
-F:	drivers/net/phy/amd-xgbe-phy.c
 
 AMS (Apple Motion Sensor) DRIVER
 M:	Michael Hanselmann <linux-kernel@hansmi.ch>

MAINTAINERS

@@ -179,10 +179,8 @@ config SUNLANCE
 
 config AMD_XGBE
 	tristate "AMD 10GbE Ethernet driver"
-	depends on (OF_NET || ACPI) && HAS_IOMEM && HAS_DMA
+	depends on ((OF_NET && OF_ADDRESS) || ACPI) && HAS_IOMEM && HAS_DMA
 	depends on ARM64 || COMPILE_TEST
-	select PHYLIB
-	select AMD_XGBE_PHY
 	select BITREVERSE
 	select CRC32
 	select PTP_1588_CLOCK

drivers/net/ethernet/amd/Kconfig

@@ -857,6 +857,48 @@
  */
 #define PCS_MMD_SELECT			0xff
 
+/* SerDes integration register offsets */
+#define SIR0_KR_RT_1			0x002c
+#define SIR0_STATUS			0x0040
+#define SIR1_SPEED			0x0000
+
+/* SerDes integration register entry bit positions and sizes */
+#define SIR0_KR_RT_1_RESET_INDEX	11
+#define SIR0_KR_RT_1_RESET_WIDTH	1
+#define SIR0_STATUS_RX_READY_INDEX	0
+#define SIR0_STATUS_RX_READY_WIDTH	1
+#define SIR0_STATUS_TX_READY_INDEX	8
+#define SIR0_STATUS_TX_READY_WIDTH	1
+#define SIR1_SPEED_CDR_RATE_INDEX	12
+#define SIR1_SPEED_CDR_RATE_WIDTH	4
+#define SIR1_SPEED_DATARATE_INDEX	4
+#define SIR1_SPEED_DATARATE_WIDTH	2
+#define SIR1_SPEED_PLLSEL_INDEX		3
+#define SIR1_SPEED_PLLSEL_WIDTH		1
+#define SIR1_SPEED_RATECHANGE_INDEX	6
+#define SIR1_SPEED_RATECHANGE_WIDTH	1
+#define SIR1_SPEED_TXAMP_INDEX		8
+#define SIR1_SPEED_TXAMP_WIDTH		4
+#define SIR1_SPEED_WORDMODE_INDEX	0
+#define SIR1_SPEED_WORDMODE_WIDTH	3
+
+/* SerDes RxTx register offsets */
+#define RXTX_REG6			0x0018
+#define RXTX_REG20			0x0050
+#define RXTX_REG22			0x0058
+#define RXTX_REG114			0x01c8
+#define RXTX_REG129			0x0204
+
+/* SerDes RxTx register entry bit positions and sizes */
+#define RXTX_REG6_RESETB_RXD_INDEX	8
+#define RXTX_REG6_RESETB_RXD_WIDTH	1
+#define RXTX_REG20_BLWC_ENA_INDEX	2
+#define RXTX_REG20_BLWC_ENA_WIDTH	1
+#define RXTX_REG114_PQ_REG_INDEX	9
+#define RXTX_REG114_PQ_REG_WIDTH	7
+#define RXTX_REG129_RXDFE_CONFIG_INDEX	14
+#define RXTX_REG129_RXDFE_CONFIG_WIDTH	2
+
 /* Descriptor/Packet entry bit positions and sizes */
 #define RX_PACKET_ERRORS_CRC_INDEX		2
 #define RX_PACKET_ERRORS_CRC_WIDTH		1
@@ -973,10 +1015,47 @@
 #define TX_NORMAL_DESC2_VLAN_INSERT		0x2
 
 /* MDIO undefined or vendor specific registers */
+#ifndef MDIO_PMA_10GBR_PMD_CTRL
+#define MDIO_PMA_10GBR_PMD_CTRL		0x0096
+#endif
+
+#ifndef MDIO_PMA_10GBR_FECCTRL
+#define MDIO_PMA_10GBR_FECCTRL		0x00ab
+#endif
+
+#ifndef MDIO_AN_XNP
+#define MDIO_AN_XNP			0x0016
+#endif
+
+#ifndef MDIO_AN_LPX
+#define MDIO_AN_LPX			0x0019
+#endif
+
 #ifndef MDIO_AN_COMP_STAT
 #define MDIO_AN_COMP_STAT		0x0030
 #endif
 
+#ifndef MDIO_AN_INTMASK
+#define MDIO_AN_INTMASK			0x8001
+#endif
+
+#ifndef MDIO_AN_INT
+#define MDIO_AN_INT			0x8002
+#endif
+
+#ifndef MDIO_CTRL1_SPEED1G
+#define MDIO_CTRL1_SPEED1G		(MDIO_CTRL1_SPEED10G & ~BMCR_SPEED100)
+#endif
+
+/* MDIO mask values */
+#define XGBE_XNP_MCF_NULL_MESSAGE	0x001
+#define XGBE_XNP_ACK_PROCESSED		BIT(12)
+#define XGBE_XNP_MP_FORMATTED		BIT(13)
+#define XGBE_XNP_NP_EXCHANGE		BIT(15)
+
+#define XGBE_KR_TRAINING_START		BIT(0)
+#define XGBE_KR_TRAINING_ENABLE		BIT(1)
+
 /* Bit setting and getting macros
  *  The get macro will extract the current bit field value from within
  *  the variable
@@ -1118,6 +1197,82 @@ do {									\
 #define XPCS_IOREAD(_pdata, _off)					\
 	ioread32((_pdata)->xpcs_regs + (_off))
 
+/* Macros for building, reading or writing register values or bits
+ * within the register values of SerDes integration registers.
+ */
+#define XSIR_GET_BITS(_var, _prefix, _field)                            \
+	GET_BITS((_var),                                                \
+		 _prefix##_##_field##_INDEX,                            \
+		 _prefix##_##_field##_WIDTH)
+
+#define XSIR_SET_BITS(_var, _prefix, _field, _val)                      \
+	SET_BITS((_var),                                                \
+		 _prefix##_##_field##_INDEX,                            \
+		 _prefix##_##_field##_WIDTH, (_val))
+
+#define XSIR0_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->sir0_regs + _reg)
+
+#define XSIR0_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XSIR0_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XSIR0_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->sir0_regs + _reg)
+
+#define XSIR0_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XSIR0_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XSIR0_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
+#define XSIR1_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->sir1_regs + _reg)
+
+#define XSIR1_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XSIR1_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XSIR1_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->sir1_regs + _reg)
+
+#define XSIR1_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XSIR1_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XSIR1_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
+/* Macros for building, reading or writing register values or bits
+ * within the register values of SerDes RxTx registers.
+ */
+#define XRXTX_IOREAD(_pdata, _reg)					\
+	ioread16((_pdata)->rxtx_regs + _reg)
+
+#define XRXTX_IOREAD_BITS(_pdata, _reg, _field)				\
+	GET_BITS(XRXTX_IOREAD((_pdata), _reg),				\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH)
+
+#define XRXTX_IOWRITE(_pdata, _reg, _val)				\
+	iowrite16((_val), (_pdata)->rxtx_regs + _reg)
+
+#define XRXTX_IOWRITE_BITS(_pdata, _reg, _field, _val)			\
+do {									\
+	u16 reg_val = XRXTX_IOREAD((_pdata), _reg);			\
+	SET_BITS(reg_val,						\
+		 _reg##_##_field##_INDEX,				\
+		 _reg##_##_field##_WIDTH, (_val));			\
+	XRXTX_IOWRITE((_pdata), _reg, reg_val);				\
+} while (0)
+
 /* Macros for building, reading or writing register values or bits
  * using MDIO.  Different from above because of the use of standardized
  * Linux include values.  No shifting is performed with the bit

drivers/net/ethernet/amd/xgbe/xgbe-common.h

@@ -910,23 +910,6 @@ static void xgbe_write_mmd_regs(struct xgbe_prv_data *pdata, int prtad,
 	else
 		mmd_address = (pdata->mdio_mmd << 16) | (mmd_reg & 0xffff);
 
-	/* If the PCS is changing modes, match the MAC speed to it */
-	if (((mmd_address >> 16) == MDIO_MMD_PCS) &&
-	    ((mmd_address & 0xffff) == MDIO_CTRL2)) {
-		struct phy_device *phydev = pdata->phydev;
-
-		if (mmd_data & MDIO_PCS_CTRL2_TYPE) {
-			/* KX mode */
-			if (phydev->supported & SUPPORTED_1000baseKX_Full)
-				xgbe_set_gmii_speed(pdata);
-			else
-				xgbe_set_gmii_2500_speed(pdata);
-		} else {
-			/* KR mode */
-			xgbe_set_xgmii_speed(pdata);
-		}
-	}
-
 	/* The PCS registers are accessed using mmio. The underlying APB3
 	 * management interface uses indirect addressing to access the MMD
 	 * register sets. This requires accessing of the PCS register in two