Merge branch 'qcom-phy-possible'

Robert Marko says:

====================
net: phy: qcom: qca808x: fill in possible_interfaces

QCA808x does not currently fill in the possible_interfaces.

This leads to Phylink not being aware that it supports 2500Base-X as well
so in cases where it is connected to a DSA switch like MV88E6393 it will
limit that port to phy-mode set in the DTS.

That means that if SGMII is used you are limited to 1G only while if
2500Base-X was set you are limited to 2.5G only.

Populating the possible_interfaces fixes this.

Changes in v2:
* Get rid of the if/else by Russels suggestion in the helper
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Author: davem330

drivers/net/phy/qcom/qca808x.c

@@ -156,6 +156,27 @@ static bool qca808x_has_fast_retrain_or_slave_seed(struct phy_device *phydev)
 	return linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
 }
 
+static bool qca808x_is_1g_only(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
+	if (ret < 0)
+		return true;
+
+	return !!(QCA808X_PHY_CHIP_TYPE_1G & ret);
+}
+
+static void qca808x_fill_possible_interfaces(struct phy_device *phydev)
+{
+	unsigned long *possible = phydev->possible_interfaces;
+
+	__set_bit(PHY_INTERFACE_MODE_SGMII, possible);
+
+	if (!qca808x_is_1g_only(phydev))
+		__set_bit(PHY_INTERFACE_MODE_2500BASEX, possible);
+}
+
 static int qca808x_probe(struct phy_device *phydev)
 {
 	struct device *dev = &phydev->mdio.dev;
@@ -220,6 +241,8 @@ static int qca808x_config_init(struct phy_device *phydev)
 		}
 	}
 
+	qca808x_fill_possible_interfaces(phydev);
+
 	/* Configure adc threshold as 100mv for the link 10M */
 	return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD,
 				     QCA808X_ADC_THRESHOLD_MASK,
@@ -350,11 +373,7 @@ static int qca808x_get_features(struct phy_device *phydev)
 	 * existed in the bit0 of MMD1.21, we need to remove it manually if
 	 * it is the qca8081 1G chip according to the bit0 of MMD7.0x901d.
 	 */
-	ret = phy_read_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_CHIP_TYPE);
-	if (ret < 0)
-		return ret;
-
-	if (QCA808X_PHY_CHIP_TYPE_1G & ret)
+	if (qca808x_is_1g_only(phydev))
 		linkmode_clear_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported);
 
 	return 0;