Skip to content

OOS 0.1.5

Choose a tag to compare

@deckerjulian deckerjulian released this 10 Nov 14:59
· 604 commits to main since this release

Sixth version of OOS, an open operating system for the Rigol DHO800/DHO900. Waveform windows and full screen, views after Auto, noise reject, Auto bandwidth by default, a fix for slow noisy signals drawn on both edges, and arrow keys on the on-screen keyboard.

Experimental. It has run on one DHO924S, and one DHO804 runs an earlier version. Read the disclaimer, the status and the known limits first. Measurements are not calibrated to any standard.

Installing and updating

No build needed: Installation.

From 0.1.1 to 0.1.4: install oos-0.1.5.oosupd through http://<scope>:8080/update. The scope restarts into the new build by itself (kexec) and installs it from there. Then switch it off at the mains, wait 30 seconds and switch it on: that start is the trial. From 0.1.0 the install is direct, followed by the same power-cycle.

What changed

  • Waveform windows: Display > Windows splits the plot into two windows side by side, two stacked, or four. Each channel, math channel and the logic analyser goes into a window of your choice, all on one time base; a drag in a window moves a channel of that window. Saved with the setup. Guide: First Steps.
  • Full screen: the button at the top right of the plot hides the top bar and the cards, the same button brings them back.
  • Views after Auto: a bar at the top of the plot offers about three periods, about ten periods, the rising edge or the falling edge of the trigger channel. Its x or a tap elsewhere closes it.
  • Fix, a slow signal drawn on both edges: with full bandwidth the noise of a slow signal can be larger than the trigger hysteresis, and the hardware then also triggers on the other edge; a 1 kHz sine at 500 us/div showed a second trace shifted by half a period, also in 0.1.4. The stock system does the same with full bandwidth (measured, trigger.md 7). The display and the waveform data now take the edge you set, nearest the hardware trigger point.
  • Bandwidth Auto by default, as on the stock system: the limit follows the sample rate, and the trigger is clean at slow time bases (100 % of the frames on the right edge in the test above, against 13 % with Full). A signal well above the limit reads smaller, so choose Full for that. Setups saved before keep their bandwidth. Auto set-up gives each channel its bandwidth back.
  • Trigger > Noise reject: 0.7 instead of 0.3 divisions of hysteresis, also :TRIGger:NREJect.
  • On-screen keyboard: arrow keys either side of Space and a tap into the entry move the insertion point, so a typo in the middle of a long WLAN password is fixed without deleting the rest.
  • The start-up screen shows the version and the build.

Full list: CHANGELOG.md.

Files

File What
oos-0.1.5.img boot image, for the second-card install in the README
oos-0.1.5.oosupd update package for a running OOS, signed with the maintainer key (id 4dbd03d9763869dd), which every build trusts
DHO800_DHO900_OOS_Install.GEL install from a USB stick through the stock system's Storage > Upgrade, without opening the scope; keep its name
SHA256SUMS checksums
linux-6.12.115-base.tar.xz kernel source, needed to build the kernel: put it into kernel/src/
busybox_1.37.0*, e2fsprogs-1.47.2.tar.xz, wpa_supplicant-2.11.tar.gz sources of the other programs in the image (the same as in 0.1.4)

State

This package was installed on the DHO924S of its author through the web page: the kexec start, the install into recovery (0.1.4 kept for rollback) and the new build running were checked; the trial start after the power-cycle is still to come. On that unit the windows, the full-screen button, the bar after Auto and its four views, the noise reject and the bandwidth were tried with the built-in generator. The keyboard arrows and the start-up line are tested on the host only.

Host tests pass. The register sequences of the acquisitions are the same as in 0.1.4 (tools/plan-matrix.sh with calibration files, 8519 lines). The USB install passes its simulation on a card file: dry run, install, selecting again, a card that is not stock refused.