Repository navigation
Releases
Hush 1.1.1
A leftover state.txt no longer looks like a live patch
/data/hush/state.txt exists while the patch is in place and is deleted once
every slot is restored. Tools read it that way: PS5Upload's upcoming hold-mode
support (phantomptr/ps5upload#651)
waits for the file to go before starting a stream.
A reboot drops the patch but not the file. After a boot with hold_s=0, a
console switched to hold mode kept the old state.txt until the first game's
window ended. Until then every stream would wait and pause for nothing.
In hold mode Hush now checks on start, and on enabled=0, whether any slot is
redirected. If none is, it deletes the leftover file and logs:
removed a stale /data/hush/state.txt: no slot is redirected
Checked on 13.60 with a planted state.txt from an earlier boot: removed at start.
Nothing else changed. With hold_s=0 the next start patches again and rewrites
the file, as before.
Install
sha256sum -c SHA256SUMS # Linux
shasum -a 256 -c SHA256SUMS # macOS
Replace hush.elf in Payload Manager. Existing config.ini files keep working.
Build
e58045cc39bb2301a4966e3c043eb75cabc45a0e5e39bb09b0b4151f57767f78 hush.elf
Reproducible with the same toolchain (-Wl,--build-id=none): two clean builds of
this tag gave this exact binary. Built with Homebrew clang/LLD 23.1.4.
Hush 1.1.0
Recording off, Remote Play on
Hush 1.0 stopped the console's continuous recording, but Remote Play goes through
the same encoder, so with Hush loaded a stream never got a picture
(#3). 1.1.0 adds a mode that
keeps both.
hold_s
hold_s=30The console builds the recording encoder once, early in a game, and does not
retry when that fails. With hold_s=N, Hush patches sceVencStartEncode when a
game process appears, holds the patch for N seconds, then restores every slot.
Recording stays off for that whole game session — Save Recent Gameplay still
answers “Gameplay isn't being recorded” — and the encoder is free for Remote
Play afterwards.
Measured on 13.60 with Kingdom Come: Deliverance II: armed within a second of the
game starting, four slots redirected, four restored 30 s later, no clip saved,
and a stream of the running game had its picture.
hold_s=0 is the default and keeps the 1.0 behaviour: the patch stays for as
long as Hush runs.
Know before you use it
- Don't connect during the window. A stream started in the first N seconds
of a game gets no picture and leaves the console on “still finishing the last
Remote Play session” until it is restarted. - Load Hush before the game. A game that is already running is skipped; it
is covered from its next start. - If a title still records, its recorder started after the window. Raise
hold_s(60, then 120); a new value applies from the next game start. - Only one title on one firmware has been measured. Reports from other games are
welcome.
Also in this release
- In hold mode
config.iniis re-read every second, soenabled=0restores and
exits within a second. - On start, slots that still point at the stub — left by a run killed mid-window
— are found and restored even withoutstate.txt. - A failed restore is logged and retried; a replaced capture daemon is detected.
rescan_sdefaults to 60 instead of 300, so slots that appear after a game
start are picked up sooner.
Full list in CHANGELOG.md.
Install
sha256sum -c SHA256SUMS # Linux
shasum -a 256 -c SHA256SUMS # macOS
Replace hush.elf in Payload Manager. Existing config.ini files keep working;
add hold_s=30 if you use Remote Play, then reboot or reload Hush.
Build
7ce9356eaf28d3fa2e3cfcd6b93300e5321c385d087409912ae3b29e6855a8d3 hush.elf
Reproducible with the same toolchain (-Wl,--build-id=none): two clean builds of
this tag gave this exact binary. Built with Homebrew clang/LLD 23.1.4.
Hush 1.0.0
The console stops recording
Hush turns off the PlayStation 5's continuous recent-gameplay recording. With
nothing encoded, there is nothing for the console to save.
What it does
SceAvCapture creates its encoder through libSceVenc. Hush resolves that
library in the live process and points every import slot of
sceVencStartEncode at an existing xor eax, eax; ret in the daemon's own code.
The call reports success and encodes nothing; compositor, scan-in and output
switching are untouched, which is why starting and quitting games keeps working.
- Discovery is symbol based — module and function resolved by name on every
start, so nothing is tied to a fixed address. - Every write is read back and compared. A run that cannot verify its end state
says so instead of claiming success. - The gadget and the exact slots are written to
state.txtatomically before
the first change, and merged with what an earlier run redirected. - A resident daemon verifies known slots every 20 s, repairs a slot that
reverts, rescans every 5 minutes and whenever the capture process is
replaced, and logs when the daemon exposes more slots than before
(slot count grew 1 -> 4).
Install
sha256sum -c SHA256SUMS # Linux
shasum -a 256 -c SHA256SUMS # macOS
Send hush.elf to Payload Manager and load it, or add local/hush to the
autoload list after ShadowMount+. Start a game: Create → Save Recent Gameplay
answers “Gameplay isn't being recorded”.
Inspect without changing anything
mode=check in /data/hush/config.ini reports the firmware version, module
base, function address, gadget and every import slot with its current target,
then exits without writing a byte. It takes no lock, so it runs alongside the
resident daemon. On a console where Hush has never run, create that file first,
otherwise the first start writes an apply config and patches immediately.
Turn it off
Set enabled=0. Within about twenty seconds Hush restores the original function
in every slot it changed, notifies, and exits. To remove it completely, also
drop local/hush from autoload and delete /data/hush/.
Limits
Firmware 13.60 is the only version tested. Hush does not check the firmware;
the lookup is not tied to a version, but the call semantics and slot layout are
unverified elsewhere, and a wrong match can crash the capture daemon until you
restart. Try mode=check first on any other firmware and open an issue with the
log.
The clip menu still lists durations — that is the console's own UI, not
something Hush changes. Nothing is written to firmware; a power cycle restores
the stock console.
Build
5c98dd0881b64eb00e90d58d90056a66193ef8ee50e2d9906a1e298b5a34c352 hush.elf
Reproducible with the same toolchain: the Makefile passes -Wl,--build-id=none,
so a rebuild with the same compiler, linker and SDK gives this exact binary. The
release was built with clang/LLD 23.1.4.