Skip to content

Releases

v0.5.2

Choose a tag to compare

@github-actions github-actions released this 17 Nov 05:37
f55ce1a

0.5.2 - 2026-11-17

🐛 Bug Fixes

Eligibility

  • Match a commit by its hash, whatever tag describes it

Release

  • Title releases with the bare tag

⚙️ Miscellaneous Tasks

Deps

  • Update rustix to 1.1.6

v0.5.1

Choose a tag to compare

@github-actions github-actions released this 17 Nov 05:02
856b9bc

0.5.1 - 2026-11-17

🚀 Features

Agent

  • Support an https Moonraker with ca_file and insecure_skip_verify

General

  • Add an installer that registers aldis with Moonraker's update manager

Self-Update

  • Install the bare release binary

Update

  • Flash older firmware with --allow-downgrade or the agent's allow_downgrade

🐛 Bug Fixes

General

  • Retry transient GitHub errors during self-update
  • End the progress step before printing a self-update error

📚 Documentation

Agent

  • State the access control boundary and tighten the prose

General

  • Describe https and TLS settings for the agent
  • Install with the installer and trim the setup and agent sections

aldis v0.5.0

Choose a tag to compare

@github-actions github-actions released this 09 Nov 04:43
19cdf5e

0.5.0 - 2026-11-09

🚀 Features

Beacon

  • Match a running beacon to its firmware file
  • Offer and update Beacons from the beacon checkout

Build

  • Build INDX firmware on mainline Klipper through indx_klipper

Cartographer

  • Match a running cartographer to an update image
  • Update a Cartographer from its firmware clone

Eligibility

  • Compare Klipper revisions and never downgrade them
  • Report firmware newer than its target as needing no update

Flash

  • Send prebuilt firmware to katapult through one validated request
  • Drive a beacon's dfu bootloader
  • Send prebuilt firmware to katapult over can too
  • Flash the Bondtech INDX through its DFU bootloader

Foci

  • Match a running foci build to its release assets
  • Look up and download foci releases
  • Remember the latest release lookup for a while
  • Offer and update FOCI MCUs from the latest FOCI release

Katapult

  • Refuse firmware linked for another application start

Moonraker

  • Read the build versions each mcu reports
  • Read the serial port a beacon section configures
  • Read the python klippy runs under

Reboot

  • Flash a beacon left in its bootloader
  • Restart klipper once a recovered beacon is back

🐛 Bug Fixes

Agent

  • Refuse non-http moonraker urls at startup

Eligibility

  • Recognise Klipper's build suffix on a clean revision

Flash

  • Verify mcu restart and reconnection around klipper startup
  • Accept a Beacon bootloader that is already idle after its last block
  • Wait for USB-CAN bridge identity change
  • Debounce re-enumerating USB identities before trusting them
  • Tell settled-but-rejected identities apart in bootloader wait logs

Foci

  • Recognize FOCI when the host reports no app

General

  • Validate mcu-reported kconfig before building
  • Verify self-update archives against published checksums
  • Cap the self-update archive download at 64 MiB
  • Bound decoded self-update archive downloads
  • Bound the direct identify exchange in time and size
  • Enforce identify deadlines and dictionary boundaries
  • Report the cause behind a native flash failure
  • Say that klipper may still be stopped after a post-flash failure
  • Show the real attempt count while waiting for klipper
  • Do not report a failed git query as a diverged checkout
  • Record expanded kconfig and document checkout config writes

Katapult

  • Resynchronize response frames after stale data
  • Bound the serial exchange and reject empty reads
  • Skip can frames katapult never sends instead of failing

Samba

  • Read the monitor's binary-mode reply instead of racing it
  • Only treat the 32 kib samd21x18 parts as flashable

Stm32

  • Refuse to guess the flash offset when the probe is ambiguous

🔧 Refactor

Agent

  • Check the klipper unit directly

Build

  • Keep klipper's own extension on the copied artifact

Cli

  • Share moonraker clients and confirmation prompts

Coordinator

  • Share build steps and simplify flash errors

Eligibility

  • Refuse every firmware downgrade through one rule

Flash

  • Share dispatch for builds and firmware files
  • Read the can bridge's usb identity through usb_sysfs
  • Share runtime, offsets, and serial open retries

General

  • Remove unused flash paths and entry points
  • Build every sudo -n command through one constructor
  • Share the failure message between update and flash
  • Drop the single-implementation checkout port
  • Route --force through the update selection
  • Give checkoutrevision one display label
  • Describe a transport in one place
  • Read an MCU's reported app and version name in one place
  • Compare firmware versions in one place
  • Stop telling users to recalibrate a Cartographer

Logging

  • Build the console layer and run-log filter once

Self-Update

  • Download any asset of a github release

Status

  • Say only that a prebuilt firmware is supported

Usb

  • Capture only the descriptor fields the report shows

📚 Documentation

General

  • List FOCI among the third-party firmware aldis updates
  • List Beacon among the third-party firmware aldis updates
  • List Cartographer among the third-party firmware aldis updates

Readme

  • Tighten the prose

aldis v0.4.0

Choose a tag to compare

@github-actions github-actions released this 24 Oct 01:51
607c8db

0.4.0 - 2026-10-24

🚀 Features

General

  • Flash SAMD21 boards through their SAM-BA bootloader
  • Flash UART-attached MCUs through Katapult
  • Confirm Katapult over UART before flashing and use the firmware's baud rate
  • Control any valid Klipper service Moonraker reports
  • Share one update lock across all users
  • Serve several Moonraker instances from one agent
  • Refuse a bridge flash while another printer on its CAN bus is busy
  • Gate bridge updates on other printers in the agent
  • Apply the bridge rule to the update and flash commands
  • Set up the agent and sudo policy for several Klipper instances

🐛 Bug Fixes

General

  • Guard SAM-BA flashing against parts and bootloaders it can't stage for
  • Wait for DFU device access before probing the flashed application
  • Clear the DFU error state after a failed application probe read
  • Choose the STM32 flash start for a firmware file from the device and Kconfig
  • Recognize USB-to-CAN bridges from the symbols a defconfig actually records
  • Quote the agent unit's config path and URLs for systemd
  • Update the TLS and tokio dependencies to clear their security advisories

🔧 Refactor

General

  • Share the SAMD21 part check and tighten SAM-BA reply parsing

📚 Documentation

General

  • Document Katapult over UART and SAMD21 SAM-BA support
  • Document running one agent for several printers

aldis v0.3.1

Choose a tag to compare

@github-actions github-actions released this 29 Sep 17:29
694b506

0.3.1 - 2026-09-29

🚀 Features

General

  • Publish 32-bit ARM release builds for Raspberry Pi

📚 Documentation

General

  • Drop the Fluidd and Mainsail sections from the README

aldis v0.3.0

Choose a tag to compare

@github-actions github-actions released this 27 Sep 22:42
5ab5d5e

0.3.0 - 2026-09-27

🚀 Features

General

  • Let commands receive a stdin payload
  • Build and install the Linux host MCU
  • Install the Linux host MCU instead of flashing it
  • Grant host MCU install and restart in the setup policy
  • Refuse to stop Klipper while a print is running
  • Serialize updates, flashes, and reboots with a host-wide lock
  • Refuse firmware changes through a remote or non-default Klipper instance
  • Speak Klipper's identify exchange directly
  • Identify serial MCUs directly when Klippy never reached them
  • Define the agent API and derive MCU status for web frontends
  • Validate agent update requests and run one update at a time
  • Back the agent with Moonraker, the local checkout, and per-run logs
  • Serve MCU status and updates to Moonraker as an agent
  • Install the Moonraker agent service with setup --agent
  • Report MCU families aldis cannot flash up front
  • Restart the agent service after a self-update

🐛 Bug Fixes

General

  • Accept 32-bit ARM host MCU builds and restart Klipper after host MCU failures
  • Re-embed the firmware version on every incremental build
  • Discover MCUs while Klippy is in an error state
  • Flash USB-to-CAN bridges after the CAN MCUs behind them
  • Never direct-identify the Linux host MCU
  • Run Moonraker discovery for remote or unsupported Klipper instances too
  • Close agent races on run overwrite and a rejected identify
  • Escape the agent unit's ExecStart executable path
  • Drop CLI restart advice from agent failures
  • Say why a USB bootloader never appeared

🔧 Refactor

General

  • Inject the command runner into host MCU dispatch
  • Move the update loop into the library behind run hooks

📚 Documentation

General

  • Describe Linux host MCU installation
  • Pick the release archive for the host architecture
  • Describe unreported MCUs, the update lock, and host checks
  • Correct the agent API doc and README against actual behavior
  • Describe the Fluidd firmware updates card
  • Describe the Mainsail firmware updates panel
  • Tighten the agent setup section and reflect auto-restart

aldis v0.2.5

Choose a tag to compare

@github-actions github-actions released this 25 Sep 01:55
b46bb79

0.2.5 - 2026-09-25

🚀 Features

General

  • Explain why an MCU is unsupported in status output
  • Surface USB identity and transport for an unsupported bootloader

🐛 Bug Fixes

General

  • Default an omitted canbus_interface to can0 during discovery
  • Restore Klipper's prior state after a pre-flash failure
  • Never let self-update downgrade a version ahead of the release
  • Stage, validate, and atomically install the sudoers policy
  • Download the release archive for the tag already resolved

🔧 Refactor

General

  • Remove UpdatePlan, unused since its inspection command was cut

📚 Documentation

General

  • Document the self-update command
  • Simplify README prose and structure

aldis v0.2.4

Choose a tag to compare

@github-actions github-actions released this 23 Sep 19:06
2233999

0.2.4 - 2026-09-23

🚀 Features

General

  • Add self-update command

aldis v0.2.3

Choose a tag to compare

@github-actions github-actions released this 23 Sep 18:22
ed6224a

0.2.3 - 2026-09-23

🚀 Features

General

  • Add hidden flash command to write an explicit firmware file
  • Accept abbreviated MCU labels for update and flash targets

aldis v0.2.2

Choose a tag to compare

@github-actions github-actions released this 21 Sep 03:33
aaac0d9

0.2.2 - 2026-09-21

🚀 Features

General

  • Show Kconfig settings in verbose inspect output

Ui

  • Default the flash, reboot, and pull confirmations to yes

Update

  • Give --all a real meaning, split from bare update and --auto

🐛 Bug Fixes

Eligibility

  • Recognize klipper's full dirty-build suffix

Flash

  • Stop requiring a serial device from non-katapult usb bootloaders
  • Bound the katapult can exchange with an absolute deadline
  • Don't abort stm32 vector-table probing on one unreadable offset

General

  • Avoid git --initial-branch in checkout_refresh test fixtures

Setup

  • Trigger udev after reloading rules

Update

  • Fail loudly on an unknown target mcu name

🔧 Refactor

General

  • Replace git2 with plain git subprocess calls in checkout

⚙️ Miscellaneous Tasks

Main

  • Drop the app-level /tmp log sweeper, systemd-tmpfiles already owns this

🏗️ Build

General

  • Publish static linux binaries