Repository navigation
tracker-ff 1.1.0
tracker-ff 1.1.0
Synth engines and per-step patch switching for the original Polyend Tracker. Polyend's synths run only on the Tracker+ and the Mini. tracker-ff is unofficial community firmware, built on Polyend's open source tracker-ce, that gives the original Tracker 16 engines of its own, made for its hardware and its memory. It goes one step further than the Tracker+: every synth part holds 16 patches and a pattern can switch between them on any step, so one instrument can change its sound mid-pattern.
What you get on top of tracker-ce
- Patch slots and the Patch FX. Every synth part keeps a bank of 16 patches in the project. The
O - Patchstep FX switches the part to one of them at a step, so a pattern can change the sound of an instrument. The slot selector is on the Synth screen. Slot 0 is the usual<N>.patch, so stock firmware opens the song with that sound and ignores the other slot files. Saving a project never deletes slot files from it, so a slot you clear comes back the next time you open the project. - 16 synth engines. ACD, FAT, VAP, WTFM, PERC, CHIP, JU6, PHZ, FM4, D-Type, CS-Type, A-Type, T-Type, 8-Type, B-Type and Arc-Type, playable as synth instruments in any project. ACD, FAT, VAP, WTFM and PERC are clean-room engines from OpenTracker (Apache-2.0). JU6, FM4, D-Type, CS-Type, A-Type, T-Type, 8-Type, B-Type and Arc-Type come from opentracker-synths by Marcin Spoczynski (MIT). CHIP is Polyend's own open Chiptune voice from tracker-ce. PHZ is a phase distortion engine written for this project from Polyend's public Synth manual.
- Polyphony. Each synth instrument has up to 4 voices from a shared voice pool. A governor drops voices when the audio load gets too high, so the Tracker never stalls. Idle audio CPU stays low.
- Patches.
.patchfiles load and save fromPatches/<ENGINE>/on the SD card. - Slot names. Each slot keeps its name when you move to another slot and back, and after saving and reloading the project. The names live in a small
<N>.namestext file next to the slot files. - Engine changes keep your sound. Switch a synth part to another engine and back and the slot 0 patch and its name come back. Slots 1 to 15 keep their names.
- Safe patch saves. A slot file is replaced through a backup copy. If the card fails or the power drops halfway, the old patch loads next time. A save that fails shows an error.
- Pitch bend works from MIDI and from the Micro-tune FX.
- Dirt master insert. Dirt (drive, fold, bitcrush) runs live on the master bus before the limiter. Pick
Dirt Soft,Dirt Hard,Dirt Fold,Dirt AsymorDirt Crushin the Saturation entry of the master screen. The presets are fixed, so there are no parameters to edit. Drive is 15 on Crush and 35 on the other four. It costs about 1.6 to 2.6 points of the audio block and nothing in silence. Based on opentracker-fx by Marcin Spoczynski (MIT).
Made for the original Tracker
tracker-ff targets the original Polyend Tracker and nothing else. Every engine, the voice pool and the governor are tuned to fit its flash, RAM and CPU. The Tracker+ and the Mini already have Polyend's synths, so on those use upstream tracker-ce.
How to flash
- Back up your
Projects/folder first. Upstream CE saves patterns in a newer format that older firmware cannot read. - Copy
PolyendTracker_FF_1.1.0.ptfto the/Firmwarefolder on the microSD card. Keep exactly one visible.ptffile in that folder, and delete or move any other one. - Put the card in the Tracker and open Config > Firmware > Firmware update. Select the file and confirm.
- Wait for the Tracker to flash and restart.
Do not rename the file. The original's bootloader lists only names that start with PolyendTrac and are at most 31 characters long.
If it does not boot
- Put a known good
.ptfin/Firmwareon the card, with no other.ptfthere. Use the official Polyend firmware or the stock CE image. - Insert the card and power the Tracker on.
- Press the recessed reset pinhole on the bottom of the Tracker with a paperclip or a SIM eject pin.
The hardware bootloader picks up the file from /Firmware and flashes it.
Go back to stock
Flash the official Polyend firmware or the stock CE .ptf the same way: copy it to /Firmware, then Config > Firmware > Firmware update and select it.
Files
PolyendTracker_FF_1.1.0.ptfis the firmware.PolyendTracker_FF_1.1.0.ziphas the same.ptfplusLICENSE,NOTICE.md,licenses/,SHA256SUMSand a short readme. Use it if you want to pass the firmware on, because the license asks you to shipLICENSEandNOTICE.mdwith it.SHA256SUMShas the checksums of the.ptfand the zip.
SHA-256 of the .ptf:
122be7c730c44c197a9bf7141c03884b22072ece3ffec664ada87f2ec56b2c2a
License
Free and non-commercial. MIT with upstream's Wholesale Commercial Clone Restriction: you can use, share and modify it for free, but you may not sell builds or clones of it. tracker-ff is not affiliated with or endorsed by Polyend. Full license texts for this project and every bundled third party component are in the zip (LICENSE, NOTICE.md, licenses/).
Source and build instructions: https://github.com/sbialy/tracker-ff