Repository navigation
Blockshot 0.5.0 — one MiniMax H3 take of 40 seconds, two upscales, and the word and time helper
One shot can now run for 40 seconds. Two ways to upscale it, a fast one and a detailed one. And a small
helper that tells you when a shot's words and its seconds do not match.
Long Take: one shot up to 40 seconds
Set a shot's Seconds above 15 and it becomes a Long Take. The field now goes up to 40. Blockshot picks
the SY Long Take (MiniMax H3) workflow for it by itself, with its voice and sound, like any other take.
A Long Take rolls at a small size, then you upscale it. That is on purpose: at a small size the person on
screen keeps the same face and the same look from the first second to the last. You pick the size under
Settings → Workflows → Long Take size:
- Clear, 736 x 416 (the default). The steadiest face in our tests. A 40 second take rolled in about
22 minutes on our test card. - Quick, 672 x 384. A good face, about 16 minutes for the same take.
- Fine, 768 x 448. A little more detail than Clear, about 24 minutes.
We rolled the same 40 second shot at five sizes and measured the face in each. Below 384 the face started to
blur and change shape in a close-up, so we left the smaller size out.
MiniMax H3 speed
MiniMax H3 takes now roll with a speed file. PDMD at 4 steps is on from the start: our 40 second take rolled
in about 4 minutes at Quick, against 16 with the slow 20 steps. Slow (20 steps) is still there to pick under
Settings → Workflows → MiniMax H3 speed, next to other speed files and any turbo LoRA you have, with your
own steps, sampler and shift. Until the PDMD file is in your ComfyUI models/loras folder, takes roll Slow,
and the card shows where to get the file. It works with any MiniMax H3 model file, the smaller fp8 and NVFP4
files too.
Upscale: Fast or Detail
Every take on the Takes screen now has two upscale buttons. There are also Fast upscale all and
Detail upscale all for the whole board.
- Fast upscale uses the NVIDIA RTX video upscaler. A 40 second take went from 736 x 416 to
1920 x 1088 in about 3 minutes on our test card. It needs an NVIDIA RTX card and thenvidia-vfx
package in ComfyUI. If that package is missing, Blockshot says so in plain words and tells you what to
install. It does not fail with a code. - Detail upscale uses SeedVR2. It draws real detail: hair, teeth, eyes. It is slow, about 45 minutes for
a 40 second take on our test card, so Blockshot asks first and shows its time guess before it starts. - After a Fast upscale the take shows Add detail. That starts again from the small take, not from the
fast copy, so nothing is upscaled twice.
Both work in short pieces of about 5 seconds that overlap and are joined with a soft blend, so the film
does not jump where two pieces meet. We checked every join on a 40 second take. The take's own sound is
kept. If an upscale stops half way, the next run carries on from the last finished piece.
A new upscale never writes over an older one. The fast copy and the detailed copy sit side by side, so you
can compare them.
The word and time helper
A talking shot needs about the right number of words for its seconds. Too few, and the speaker fills the
gap with words of their own. Too many, and the speaker rushes or drops words.
Each shot with spoken lines now shows a note under its Seconds field:
- "22 words for 10 s. That fits (19 to 30 words)." in green, or
- "Too many words: 40 for 10 s. Cut about 10 words or make the shot 16 s." in amber.
The Use N s button sets the seconds that fit the words in one click. The shot card on the board also
gets a small warning mark, so you can see which shots need a look without opening each one.
The helper counts about 2.5 words a second. Short shots keep 2 seconds of quiet for a breath. A Long Take
does not.
Fixed
A second roll of the same shot with the same seed wrote over the first take's file. Both takes then
showed the newer film. Each roll now gets its own file, so an older take stays as it was.
Get it
| File | What it is |
|---|---|
Blockshot-Setup-0.5.0.exe |
the installer, for your user only, no admin — 97,343,746 bytes, sha256 3207abac8e042f11f6e1ae607722bc32d1c1fc2cab6bef1b84814fe27c6bdc20 |
Blockshot-0.5.0-portable.zip |
unzip anywhere and double-click Blockshot.cmd — 127,497,769 bytes, sha256 b13380062cd8150dd8e1b5a3209b0cdd8e9dbd10e07825c2cebd559c27f5d993 |
Each file has its .sha256 next to it. Windows shows its blue box once because the file is not signed
yet: More info → Run anyway.
Close the old Blockshot from the tray icon first. Your boards, settings and key stay where they are.