Repository navigation
Blockshot 0.6.0
Swap a person in a clip, edit buttons on every frame, a Tools page, Looks, new take modes, and everything is free for everyone.
Everything is free
Every feature is open to everyone on a fresh install. No key is needed. Your existing key keeps working and changes nothing.
What is new
-
The cut can now close on an end card: pick none, the "Made with Blockshot" card, or a card with your film's title. It holds for 3 seconds. A music file and its loudness are set per cut as well, and the music fades in and out under the film.
-
New Tools page in the top menu, free for everyone, everything runs on your own PC: a Captioner (one caption text file per picture, written by a vision model you already run in LM Studio or Ollama; if you have none it tells you which kind to load), a Media Shrinker (smaller copies of a folder of pictures and videos in a new folder, your originals are never touched, with progress, Cancel and Retry), and a Prompt Studio (type a few words, get a rich picture prompt and a video prompt from your own Writer, with copy buttons).
-
Every frame now has an "Edit this frame" row: New angle, Next shot, Keep this face, Change a detail, More real and Guide picture. Each button draws a new version of the frame and never writes over the old one. A strip of small pictures under the frame lets you pick any version, and Undo goes back one step. While it works you can Cancel; if it fails you can Try again. The buttons are grey, with the reason, until the edit files are on your PC.
-
A third Picture preset, "Cast portrait", draws a frame from the portrait of the person in it so the face stays the same. A frame with no portrait is drawn the usual way. The edit files are large and are not hosted by us: the Models step links to their pages and checks the folder you saved them in.
-
Takes now come in three modes, picked in the Takes section: Normal, Turbo draft and From pictures. Turbo draft is a fast, rougher take for checking a shot before you spend a long render on it. From pictures builds a take from the portraits of the people in the shot, the set picture and the shot's frame, so it works even before any frame is kept; each picture is named in the prompt, so the film knows who is who. Each mode uses its own workflow and its own model files, and the Takes section says which file is missing if one is.
-
A take can now end on a picture you choose. Open "Edit this frame" on a shot and press "Use as end frame": the take of the shot before it will finish on this frame, which makes cuts between shots line up. Press it again to clear it. New installs get this in the standard take workflow; an install that already has the older workflow keeps it until you re-add the starter.
-
New: Swap a person in a clip, on every board and open to everyone. Pick a clip of up to 10 seconds and one picture of the new person, then press Start. If the clip shows several people, they are outlined and numbered so you can pick the one to swap; if there is only one, you are not asked. A progress card shows the five steps and the time left, and you can Cancel at any time. By default the new first picture is shown to you before the long part starts, so you can Continue, Redo or Cancel. When it is done the new clip sits next to the original with Play, Keep and Discard, and a small text file beside it lists what was done and any part that needs a closer look. Everything outside the person is kept from the original, and the original sound is kept. It needs large model files that are not hosted by us; the button is grey, with the reason, until they are on your PC. A quick note on use: use only clips and pictures you have the right to use, and label the result as made by software.
-
The swap draws sharper faces: Standard quality is the default, with more drawing steps and a gentle sharpen before the person is put back (it takes longer than before; the time shown on the card is updated). If the new first picture keeps the old trousers or shoes instead of the new person's, it is drawn again, up to three times, and a note says so if it still did not carry over.
-
Looks: every board now has a Look in its Brief. Pick one of six film looks (Clean daylight, Warm film stock, Cold thriller, Grainy analog, Soft dreamy, High contrast noir) and every picture on that board is drawn in that style, with a matching list of things to keep out. Pick Custom and the board uses your own house style from Settings again; your own words are never changed or lost when you try a look. Nothing to download. Later, look packs can add more looks, and a look can name an extra style file that is used only if you have it.
-
Looks can also name a LoRA style file and their own steps and strength. The LoRA is used only for pictures and only if you have the file in ComfyUI.
Also in this version
- Everything from 0.5.2 (the clearer "port is busy" message).
- Fixed: nine small rough edges found while testing, and the Setup step for the Wan file.
Get it
| File | What it is |
|---|---|
Blockshot-Setup-0.6.0.exe |
Windows installer, for your user only, no admin — 98,498,585 bytes, sha256 46dd41f13257736e3d35c1a51c58810788239f6ec2343b031107d10193f2c9d8 |
Blockshot-0.6.0-portable.zip |
Windows, unzip anywhere and double-click Blockshot.cmd — 129,728,929 bytes, sha256 f9c4d5610eb83bce7b99219db45832f2aa65170cc71f2f716b3ec8dce492e788 |
Blockshot-0.6.0-linux-x64.tar.gz |
Linux 64-bit, run ./Blockshot/blockshot.sh — 117,735,206 bytes, sha256 7f43ba008595491887ffaf4556a10251bd5ca3818c8eb4f5fc79c609a8349b70 |
Each file has its .sha256 next to it. Windows shows its blue box once because the file is not signed
yet: More info → Run anyway.
Close the old Blockshot first: right-click the icon near the clock and choose Quit.