Skip to content

Releases

thingino-backpack 0.2.0

Choose a tag to compare

@github-actions github-actions released this 01 Oct 12:09

What's new

  • Flash programmer. With a SOIC-8 clip on the camera's flash, the unit speaks flashrom's
    serprog protocol on port 8888 (flashrom 1.4.0 or later; IPv4 only, until flashrom has IPv6).
  • Firmware updates over the web. Upload a release's -app.bin in the status page's
    Firmware section, or with curl. A new firmware that is not back on the network within
    five minutes rolls back by itself.
  • Wi-Fi TX power on the status page, 2 to 20 dBm.
  • BOOTSEL, a second boot pin (GPIO6) for boards that bring out the SoC's boot select:
    pulled low or driven high, as set.
  • One pinout for every S2 and S3 board, all on GPIO1 to 9: DevKitC-style boards, the
    XIAO ESP32S3, the S3 Super Mini, the Waveshare ESP32-S3-Zero and the S2 Mini.
  • The esp32s3-psram image is gone: esp32s3 runs on every S3 module.

Upgrading from 0.1.x

  • Rewire. Camera UART TX and RX are on GPIO1 and GPIO2, power on GPIO4, the boot pin on
    GPIO9, BOOTSEL on GPIO6, and the clip's CS, CLK and DO on GPIO5, GPIO7 and GPIO8. See
    Wiring in the README.
  • Write the first-install image once, over USB. 0.2.0 has two firmware slots, so the
    partition table changed. The first-install image erases the Wi-Fi settings; set them up
    again in the portal. Every update after that can go over the web.

Per chip, thingino-backpack-<chip>.bin is a first install: write it at 0x0. It holds
the bootloader, the partition table and the app, and erases the saved Wi-Fi, so the
unit starts in its setup portal. thingino-backpack-<chip>-app.bin is an update that
keeps the Wi-Fi settings: upload it in the status page's Firmware section, or write it
at 0x20000 over USB after erasing the OTA state.

esptool.py --chip esp32s3 write_flash 0x0 thingino-backpack-esp32s3.bin
curl -X POST --data-binary @thingino-backpack-esp32s3-app.bin http://<host>.local/api/ota

Units on 0.1.x have the single-slot layout and take the first-install image once.

esp32s3 runs on every ESP32-S3 module, PSRAM or not. The esp32s2 and esp32p4
images are untested on hardware; see the README.

Full Changelog: v0.1.1...v0.2.0

thingino-backpack 0.1.1

Choose a tag to compare

@github-actions github-actions released this 30 Sep 01:42

Per chip, thingino-backpack-<chip>.bin is a first install: write it at 0x0. It holds
the bootloader, the partition table and the app, and erases the saved Wi-Fi, so the
unit starts in its setup portal. thingino-backpack-<chip>-app.bin is an update that
keeps the Wi-Fi settings: write it at 0x10000.

esptool.py --chip esp32s3 write_flash 0x0 thingino-backpack-esp32s3.bin
esptool.py --chip esp32s3 write_flash 0x10000 thingino-backpack-esp32s3-app.bin

esp32s3 needs no PSRAM, esp32s3-psram is for modules with octal PSRAM. The
esp32s2 and esp32p4 images are untested on hardware; see the README.

Full Changelog: v0.1.0...v0.1.1

thingino-backpack 0.1.0

Choose a tag to compare

@github-actions github-actions released this 29 Sep 22:36

Per chip, thingino-backpack-<chip>.bin is a first install: write it at 0x0. It holds
the bootloader, the partition table and the app, and erases the saved Wi-Fi, so the
unit starts in its setup portal. thingino-backpack-<chip>-app.bin is an update that
keeps the Wi-Fi settings: write it at 0x10000.

esptool.py --chip esp32s3 write_flash 0x0 thingino-backpack-esp32s3.bin
esptool.py --chip esp32s3 write_flash 0x10000 thingino-backpack-esp32s3-app.bin

esp32s3 needs no PSRAM, esp32s3-psram is for modules with octal PSRAM. The
esp32s2 and esp32p4 images are untested on hardware; see the README.

Full Changelog: https://github.com/thingino/thingino-backpack/commits/v0.1.0