guides/printers/creality/

[giscus[bot]]

guides/printers/creality/

https://3ms.3dcoded.xyz/guides/printers/creality/

[dr-evil-23]

I did this, and flashed Katapult and Klipper to the SKR Pico, as instructed, but both of them won't talk to each other. I get this error message :

"MCU Protocol error

This type of error is frequently caused by running an older
version of the firmware on the micro-controller (fix by
recompiling and flashing the firmware).

Your Klipper version is: 09faed31-dirty
MCU(s) which should be updated:
mcu: Current version 341a2c18-dirty-20230717_153001-cxsw-virtual-machine
Up-to-date MCU(s):

Once the underlying issue is corrected, use the "RESTART"
command to reload the config and restart the host software.

mcu 'mmu': Multi-byte msgtag not supported"

How can I fix this?

Thank you

[dr-evil-23]

Oh, and now MMU MCU is reporting 0.8% usage at idle, and about 2.1% while moving steppers, instead of ±20%, in Fluidd.

[dr-evil-23]

So basically, you need to compile katapult and klipper v0.12 (https://github.com/Klipper3d/klipper/releases/tag/v0.12.0) with "W25Q080 with CLKDIV 2" instead of "GENERIC_03H with CLKDIV 4", program the skr pico as specified in the instructions provided on this website, and do all the modification that was on the "Creality K1/E3v3 Series" when I started, to install helper-script and happy-hare, then you're good to go, it just works 😄

[dr-evil-23]

Interesting. I’m curious to see how it works out.

I've been printing with it for over a month now, works great 😄

[3DCoded]

Great! I've added your method to this page. Thank you!

[dr-evil-23]

Still printing, still working, had to adjust happy hare a bit because I kept demagnetizing the Nema 17 motors, it's a fast printer and the gears have a hard time following up with all the sudden moves, so I tend to set a too high current for syncing up, but I'm getting there :D

[mountainman84654-sudo]

I have a question I am running an ender5 S1 with sonicpad will this work to operate the 3ms
I know I can update the sonicpad to debian if needed i have another one running it

[3DCoded]

Hi @mountainman84654-sudo ,

If your Sonic Pad can run mainline Klipper on Debian it should work fine with the 3MS.

[mountainman84654-sudo]

I tried the configuration generator and all i get is an error I want to make sure i have everything figured out before I install it and change my Sonic pad to Debian to get this to run any help would be greatfull

[mountainman84654-sudo]

Ok I have everything built but dont find any information on the BTT SKR Mini or is it the same as the Pico
also setting up filament sensor on head does it have to be run through the main or the BTT SKR mini
and you have information about Creality K1/E3v3 series but what about Ender 5 S1
Im just hoping to get this working with out to much hassel and would like any help and information You can provide
Please and Thank You Donnie Gates (MM3D Printing)

[3DCoded]

Hi @mountainman84654-sudo ,

For the SKR Mini, there isn’t an official mount but you can use the config generator . The filament sensor can go on any board that Klipper is connected to. For the Ender 5 S1, from what I can tell it doesn’t run Klipper from factory so if you installed Klipper yourself you should be ok. The creality specific guide is for printers with a modified Klipper pre installed so you should be able to follow the normal guide.

[mountainman84654-sudo]

mine already runs klipper with sonicpads version but am going to update it to Debian and run I already have one that runs Co-Prints color changer with 8 color and running Debian on its sonicpad runs flawless and hoping this will do the same or better but when i put the klipper config file in the generator this is what i get back

Step 1: Uploading your base configuration
Some errors were found in your config. Please see below to fix them.
File contains no section headers. file: '', line: 1 'Error fetching configuration
Error fetching configuration

do i even need to run that or what board would I select on Happy Hare to get it set up the quick start page dont show my board but I have not went that far to find out what ones are supported I just dont want to disable one of my printers before I have all the information and all my ducks in a row to make this work

Thanks again Donnie Gates (MM3D Printing )

[3DCoded]

Hi @mountainman84654-sudo ,

For the sonic pad, I would recommend flashing Debian as the sonic pad by default runs a Creality modified Klipper.
For the config generator, you should be uploading the config for the SKR Mini (as if you were going to run your printer off of it). I can also generate the config for you if you tell me which SKR Mini it is (E3 V2, E3 V3, etc.). Currently the HH quickstart does not provide a SKR Mini config so you'd have to select other. If you want your printer functional while you figure out HH config you can comment out the [include mmu...] lines at the top of your printer.cfg

[mountainman84654-sudo]

BTT SKR MINI E3 V2.0 is the board

[3DCoded]

Thank you @mountainman84654-sudo ,

I've linked your config with installation instructions. https://www.3dcoded.xyz/configgenerator/568/