rv/sg204x: update patchset

arch/riscv/boot/dts/sophgo/sg2042.dtsi

@@ -234,7 +234,7 @@
 			reg-names = "clr", "doorbell";
 			msi-controller;
 			#msi-cells = <0>;
-			msi-ranges = <&intc 64 IRQ_TYPE_LEVEL_HIGH 32>;
+			msi-ranges = <&intc 64 IRQ_TYPE_EDGE_RISING 32>;
 		};
 
 		rpgate: clock-controller@7030010368 {

arch/riscv/boot/dts/sophgo/sg2044.dtsi

@@ -214,7 +214,7 @@
 			reg-names = "clr", "doorbell";
 			#msi-cells = <0>;
 			msi-controller;
-			msi-ranges = <&intc 352 IRQ_TYPE_LEVEL_HIGH 512>;
+			msi-ranges = <&intc 352 IRQ_TYPE_EDGE_RISING 512>;
 			status = "disabled";
 		};
 

arch/riscv/include/asm/errata_list_vendors.h

@@ -4,8 +4,8 @@
 #define ASM_ERRATA_LIST_VENDORS_H
 
 #ifdef CONFIG_ERRATA_ANDES
-#define ERRATA_ANDES_NO_IOCP 0
-#define ERRATA_ANDES_NUMBER 1
+#define	ERRATA_ANDES_NO_IOCP 0
+#define	ERRATA_ANDES_NUMBER 1
 #endif
 
 #ifdef CONFIG_ERRATA_SIFIVE
@@ -22,4 +22,4 @@
 #define	ERRATA_THEAD_NUMBER 4
 #endif
 
-#endif
+#endif /* ASM_ERRATA_LIST_VENDORS_H */

arch/riscv/include/asm/pgtable.h

@@ -654,6 +654,15 @@ static inline pgprot_t pgprot_writecombine(pgprot_t _prot)
 	return __pgprot(prot);
 }
 
+/*
+ * DMA allocations for non-coherent devices use what the RISC-V architecture
+ * call "Non-Cacheable" memory attribute, which permits idempotent, weakly-ordered
+ * (RVWMO), main memory. This is different from "I/O" memory attribute which is
+ * intended for MMIO access with Non-cacheable, non-idempotent, strongly-ordered
+ * (I/O ordering), I/O attributes.
+ */
+#define pgprot_dmacoherent pgprot_writecombine
+
 /*
  * Both Svade and Svadu control the hardware behavior when the PTE A/D bits need to be set. By
  * default the M-mode firmware enables the hardware updating scheme when only Svadu is present in

arch/riscv/kernel/pi/cmdline_early.c

@@ -41,9 +41,9 @@ static char *get_early_cmdline(uintptr_t dtb_pa)
 static u64 match_noXlvl(char *cmdline)
 {
 	if (strstr(cmdline, "no4lvl"))
-		return SATP_MODE_48;
+		return SATP_MODE_39;
 	else if (strstr(cmdline, "no5lvl"))
-		return SATP_MODE_57;
+		return SATP_MODE_48;
 
 	return 0;
 }

arch/riscv/kernel/pi/fdt_early.c

@@ -3,6 +3,7 @@
 #include <linux/init.h>
 #include <linux/libfdt.h>
 #include <linux/ctype.h>
+#include <asm/csr.h>
 
 #include "pi.h"
 
@@ -183,3 +184,42 @@ bool fdt_early_match_extension_isa(const void *fdt, const char *ext_name)
 
 	return ret;
 }
+
+/**
+ *  set_satp_mode_from_fdt - determine SATP mode based on the MMU type in fdt
+ *
+ * @dtb_pa: physical address of the device tree blob
+ *
+ *  Returns the SATP mode corresponding to the MMU type of the first enabled CPU,
+ *  0 otherwise
+ */
+u64 set_satp_mode_from_fdt(uintptr_t dtb_pa)
+{
+	const void *fdt = (const void *)dtb_pa;
+	const char *mmu_type;
+	int node, parent;
+
+	parent = fdt_path_offset(fdt, "/cpus");
+	if (parent < 0)
+		return 0;
+
+	fdt_for_each_subnode(node, fdt, parent) {
+		if (!fdt_node_name_eq(fdt, node, "cpu"))
+			continue;
+
+		if (!fdt_device_is_available(fdt, node))
+			continue;
+
+		mmu_type = fdt_getprop(fdt, node, "mmu-type", NULL);
+		if (!mmu_type)
+			break;
+
+		if (!strcmp(mmu_type, "riscv,sv39"))
+			return SATP_MODE_39;
+		else if (!strcmp(mmu_type, "riscv,sv48"))
+			return SATP_MODE_48;
+		break;
+	}
+
+	return 0;
+}

arch/riscv/kernel/pi/pi.h

@@ -14,6 +14,7 @@ u64 get_kaslr_seed(uintptr_t dtb_pa);
 u64 get_kaslr_seed_zkr(const uintptr_t dtb_pa);
 bool set_nokaslr_from_cmdline(uintptr_t dtb_pa);
 u64 set_satp_mode_from_cmdline(uintptr_t dtb_pa);
+u64 set_satp_mode_from_fdt(uintptr_t dtb_pa);
 
 bool fdt_early_match_extension_isa(const void *fdt, const char *ext_name);
 

arch/riscv/mm/init.c

@@ -816,6 +816,7 @@ static __meminit pgprot_t pgprot_from_va(uintptr_t va)
 
 #if defined(CONFIG_64BIT) && !defined(CONFIG_XIP_KERNEL)
 u64 __pi_set_satp_mode_from_cmdline(uintptr_t dtb_pa);
+u64 __pi_set_satp_mode_from_fdt(uintptr_t dtb_pa);
 
 static void __init disable_pgtable_l5(void)
 {
@@ -855,18 +856,22 @@ static void __init set_mmap_rnd_bits_max(void)
  * underlying hardware: establish 1:1 mapping in 4-level page table mode
  * then read SATP to see if the configuration was taken into account
  * meaning sv48 is supported.
+ * The maximum SATP mode is limited by both the command line and the "mmu-type"
+ * property in the device tree, since some platforms may hang if an unsupported
+ * SATP mode is attempted.
  */
 static __init void set_satp_mode(uintptr_t dtb_pa)
 {
 	u64 identity_satp, hw_satp;
 	uintptr_t set_satp_mode_pmd = ((unsigned long)set_satp_mode) & PMD_MASK;
-	u64 satp_mode_cmdline = __pi_set_satp_mode_from_cmdline(dtb_pa);
+	u64 satp_mode_limit = min_not_zero(__pi_set_satp_mode_from_cmdline(dtb_pa),
+					   __pi_set_satp_mode_from_fdt(dtb_pa));
 
 	kernel_map.page_offset = PAGE_OFFSET_L5;
 
-	if (satp_mode_cmdline == SATP_MODE_57) {
+	if (satp_mode_limit == SATP_MODE_48) {
 		disable_pgtable_l5();
-	} else if (satp_mode_cmdline == SATP_MODE_48) {
+	} else if (satp_mode_limit == SATP_MODE_39) {
 		disable_pgtable_l5();
 		disable_pgtable_l4();
 		return;

drivers/irqchip/irq-sg2042-msi.c

@@ -30,6 +30,7 @@ struct sg204x_msi_chip_info {
  * @doorbell_addr:	see TRM, 10.1.32, GP_INTR0_SET
  * @irq_first:		First vectors number that MSIs starts
  * @num_irqs:		Number of vectors for MSIs
+ * @irq_type:		IRQ type for MSIs
  * @msi_map:		mapping for allocated MSI vectors.
  * @msi_map_lock:	Lock for msi_map
  * @chip_info:		chip specific infomations
@@ -41,6 +42,7 @@ struct sg204x_msi_chipdata {
 
 	u32					irq_first;
 	u32					num_irqs;
+	unsigned int				irq_type;
 
 	unsigned long				*msi_map;
 	struct mutex				msi_map_lock;
@@ -137,14 +139,14 @@ static int sg204x_msi_parent_domain_alloc(struct irq_domain *domain, unsigned in
 	fwspec.fwnode = domain->parent->fwnode;
 	fwspec.param_count = 2;
 	fwspec.param[0] = data->irq_first + hwirq;
-	fwspec.param[1] = IRQ_TYPE_EDGE_RISING;
+	fwspec.param[1] = data->irq_type;
 
 	ret = irq_domain_alloc_irqs_parent(domain, virq, 1, &fwspec);
 	if (ret)
 		return ret;
 
 	d = irq_domain_get_irq_data(domain->parent, virq);
-	return d->chip->irq_set_type(d, IRQ_TYPE_EDGE_RISING);
+	return d->chip->irq_set_type(d, data->irq_type);
 }
 
 static int sg204x_msi_middle_domain_alloc(struct irq_domain *domain, unsigned int virq,
@@ -298,6 +300,7 @@ static int sg2042_msi_probe(struct platform_device *pdev)
 	}
 
 	data->irq_first = (u32)args.args[0];
+	data->irq_type = (unsigned int)args.args[1];
 	data->num_irqs = (u32)args.args[args.nargs - 1];
 
 	mutex_init(&data->msi_map_lock);

drivers/pci/controller/cadence/pcie-sg2042.c

@@ -41,10 +41,8 @@ static int sg2042_pcie_probe(struct platform_device *pdev)
 	int ret;
 
 	bridge = devm_pci_alloc_host_bridge(dev, sizeof(*rc));
-	if (!bridge) {
-		dev_err_probe(dev, -ENOMEM, "Failed to alloc host bridge!\n");
-		return -ENOMEM;
-	}
+	if (!bridge)
+		return dev_err_probe(dev, -ENOMEM, "Failed to alloc host bridge!\n");
 
 	bridge->ops = &sg2042_pcie_root_ops;
 	bridge->child_ops = &sg2042_pcie_child_ops;
@@ -60,10 +58,8 @@ static int sg2042_pcie_probe(struct platform_device *pdev)
 	devm_pm_runtime_enable(dev);
 
 	ret = cdns_pcie_init_phy(dev, pcie);
-	if (ret) {
-		dev_err_probe(dev, ret, "Failed to init phy!\n");
-		return ret;
-	}
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to init phy!\n");
 
 	ret = cdns_pcie_host_setup(rc);
 	if (ret) {

drivers/pci/quirks.c

@@ -6432,3 +6432,26 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x461f, quirk_no_shutdown);  // Thu
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x462f, quirk_no_shutdown);  // Thunderbolt 4 PCI Express Root Port
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x466d, quirk_no_shutdown);  // Thunderbolt 4 NHI
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x46a8, quirk_no_shutdown);  // GPU
+
+/*
+ * PCI switches integrated into Intel Arc GPUs have BAR0 that prevents
+ * resizing the BARs of the GPU device due to that bridge BAR0 pinning the
+ * bridge window it's under in place. Nothing in pcieport requires that
+ * BAR0.
+ *
+ * Release and disable BAR0 permanently by clearing its flags to prevent
+ * anything from assigning it again.
+ */
+static void pci_release_bar0(struct pci_dev *pdev)
+{
+	struct resource *res = pci_resource_n(pdev, 0);
+
+	if (!res->parent)
+		return;
+
+	pci_release_resource(pdev, 0);
+	res->flags = 0;
+}
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_INTEL, 0x4fa0, pci_release_bar0);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_INTEL, 0x4fa1, pci_release_bar0);
+DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_INTEL, 0xe2ff, pci_release_bar0);

tools/perf/pmu-events/arch/riscv/mapfile.csv

@@ -20,5 +20,6 @@
 0x489-0x8000000000000008-0x[[:xdigit:]]+,v1,sifive/p550,core
 0x489-0x8000000000000[1-6]08-0x[9b][[:xdigit:]]+,v1,sifive/p650,core
 0x5b7-0x0-0x0,v1,thead/c900-legacy,core
+0x5b7-0x80000000090c0d00-0x2047000,v1,thead/c900-legacy,core
 0x67e-0x80000000db0000[89]0-0x[[:xdigit:]]+,v1,starfive/dubhe-80,core
 0x31e-0x8000000000008a45-0x[[:xdigit:]]+,v1,andes/ax45,core