Publish via CloudCannon

docs/products/m1/setup/getting-started-m1.md

@@ -10,7 +10,7 @@ Congrats on your new M-1! Below we will go through steps to get you up and runni
 
 Your device is ready to connect to your Wi-Fi and begin controlling via Home Assistant, the WLED app for iPhone and Android, or via a web browser!
 
-1\. Plug in the USB-C power in and the M-1 device will boot within a couple seconds. Head to the available Wi-Fi networks on your phone and select WLED-AP. It should pop up saying "Welcome to WLED!". If this popup does not occur, please open a web browser and navigate to <a href="http://4.3.2.1/" target="_blank" rel="noopener">http://4.3.2.1/</a> or <a href="http://wled.me" target="_blank" rel="noreferrer nofollow noopener">http://wled.me</a> and you should be prompted with the same image seen below.
+1\. Plug in the USB-C power in and the M-1 device will boot within a couple seconds. Head to the available Wi-Fi networks on your phone and select Apollo M-1. It should pop up saying "Welcome to WLED!". If this popup does not occur, please open a web browser and navigate to <a href="http://4.3.2.1/" target="_blank" rel="noopener">http://4.3.2.1/</a> or <a href="http://wled.me" target="_blank" rel="noreferrer nofollow noopener">http://wled.me</a> and you should be prompted with the same image seen below.
 
 ![](../../../assets/m-1-getting-started.png)
 

docs/products/m1/troubleshooting/m1-reflash.md

@@ -4,28 +4,38 @@ description: Step by step guide for re-flashing the M-1 back to factory firmware
 ---
 # Factory Re-Flash M-1
 
+!!! info "If your device becomes unresponsive and you've exhausted the other troubleshooting methods you can reflash the factory firmware by following the steps below."
+
+    This factory re-flash needs to be done in Chrome, Edge, or another Chromium based browser.
+
 1\. Plug in a USB cable that supports power and data into your computer.
 
 2\. Push and hold the boot button (the right button). While still holding the button down, plug in a USB-C cable into the USB-C port of your M-1 LED Matrix then let go of the button.
 
 ![](../../../assets/m-1-hold-boot-webp.webp)
 
-3\. Download the firmware <a href="https://github.com/MoonModules/WLED/releases/download/v0.14.1-beta.32/WLEDMM_0.14.1-b32.40_adafruit_matrixportal_esp32s3.bin" target="_blank" rel="noreferrer nofollow noopener">.bin file from here</a>.
+3\. Navigate to our installer page and click connect under <a href="https://apolloautomation.github.io/WLED-MM-M1/" target="_blank" rel="noreferrer nofollow noopener">Apollo M-1 Installer</a>.
+
+![](../../../assets/m-1-reflash-connect-button.png)
+
+4\. Select the open com port then click Connect.
+
+![](../../../assets/m-1-reflash-com-port.png)
 
-4\. Download <a href="https://wiki.apolloautomation.com/static/ESP-Flasher.exe" title="Click here to download the ESP-Flasher Tool" target="_blank" rel="noreferrer nofollow noopener">ESP Flasher (Windows EXE)</a> and open it.
+5\. Click Install M-1.
 
-5\. Click the **Serial Port** dropdown and choose the available COM port..
+![](../../../assets/m-1-reflash-click-install.png)
 
-![](../../../assets/m-1-select-open-com-port.png)
+5\. Click Install.
 
-6\. Browse to the firmware file from Step 3 and select it.
+![](../../../assets/m-1-reflash-click-install-confirm.png)
 
-![](../../../assets/m-1-select-firmware-you-downloaded.png)
+6\. Once you see "Installation complete!" you are finished. Click Next then close out of the browser window.
 
-7\. Click **Flash ESP** and wait for the process to complete. Once it's done, it will appear as shown in the image below.
+![](../../../assets/m-1-reflash-install-complete.png)
 
-![](../../../assets/m-1-reflash-completed.png)
+!!! warning "Power cycle your device before doing anything else!"
 
-8\. The device is still in **boot mode** and needs to be power cycled. To reboot it, either unplug the power cable or press the **reset button** on the back of the device (the button on the right).
+    Your device is still in boot mode and needs to be power cycled aka power removed to make it boot in a normal mode!
 
-[Head to the Getting Started article to setup your M-1 as a new device!](https://wiki.apolloautomation.com/products/m1/setup/getting-started-m1/){   .md-button .md-button--primary }
+[Head to the Getting Started article to setup your M-1 as a new device!](https://wiki.apolloautomation.com/products/m1/setup/getting-started-m1/){      .md-button .md-button--primary }

docs/products/pump1/faq.md

@@ -2,5 +2,22 @@
 title: PUMP-1 FAQ
 description: Frequently asked questions about the PUMP-1 Fluid Pump Sensor
 ---
-# NEED TO DO THIS
+1\. **What is the maximum distance this pump can push water?**
 
+* The PUMP-1 has been successfully tested with 33 feet of tubing and a vertical lift of 14 feet, while still maintaining strong head pressure. This demonstrates its capability to move water efficiently over long distances and significant elevation gains.
+
+2\. **What motor is used for the PUMP-1?**
+
+* The motor used is a jrk-370sh-18215.
+
+3\. **Question?**
+
+* Answer.
+
+4\. **Question?**
+
+* Answer.
+
+5\. **Question?**
+
+* Answer.

docs/products/pump1/setup/pump1-sensor-definitions.md

@@ -90,4 +90,4 @@ This serves as a list of all sensor definitions to help understand what each ent
 
     * Shows the time since last reboot.
 
-[Join our Discord if you need more help! :simple-discord:](https://dsc.gg/apolloautomation){                        .md-button }
+[Join our Discord if you need more help! :simple-discord:](https://dsc.gg/apolloautomation){                         .md-button }