Wiki-RC1.17 — accuracy audit fixes: backup path, SSH user, Mainsail option 7, RC3.01
Corrects the wiki against Q2/aio_menu.sh. Findings where the code (not the
wiki) is wrong are deliberately left alone pending the code fix.
CRITICAL
- Backups: replace the ~/mudstockbackups/ + _FIRST_STOCK claim with the real
single fixed snapshot at ~/aio_config_backup/; note revert refuses to run if
it is missing. (FAQ, Install Guide, Troubleshooting)
- SSH login user on 01.01.02+ is mks/makerbase, not qidi; /home/mks is a
symlink to /home/qidi. Removed all "use qidi instead" instructions.
MAJOR
- Mainsail is option 7; option 6 is Uninstall Mainsail. (Install Guide, BunnyBox)
- Revert does not restart Klipper — run FIRMWARE_RESTART yourself.
- Addons 4 and 7 are blocked on 01.01.02+ firmware.
- Document the Testing submenu (option 10), incl. its two destructive entries.
- Document Uninstall Mainsail (6) and About (8).
- BunnyBox: the install stops mid-run for an at-the-printer HelixScreen wizard;
warn before starting and explain the degraded-dashboard failure mode.
- BunnyBox: the screen switches to HelixScreen during the install, not after
the FIRMWARE_RESTART.
- Just Faster Box: the file to edit on the printer is gcode_macro.cfg.
- G32 is a one-print toggle — PRINT_END runs G31 at the end of every print.
- aoi.ini example refreshed to RC3.01.
MINOR
- Menu preview version RC3.00 -> RC3.01; menu layout itself unchanged.
- Health Check also covers runtime service health and backs up before repair.
- bluetoothd -> bluetooth, strongswan -> strongswan-starter; only packagekit,
QIDILink-client and the pulseaudio user units are masked.
- print_end lowers the bed to 5 mm above the bottom, not "all the way down".
- Process optimization is prompted, not automatic.
- Screw_Tilt_adjust button ships with Just Faster Printer only.
- Orca download unpinned from v2.3.2; fan calibration requires
[fan_generic cooling_fan]; OctoApp PRINTER_IP line is already uncommented
(asset comment corrected to match).
New documentation
- Getting Started: the repo's 8 Orca printer presets.
- Install Guide: camera streaming (ustreamer + nginx proxy) and its prompts.
- BunnyBox: the Upgrade / Fresh install / Cancel re-install choice and the
stale-artifact cleanup prompt.
- Just Faster: the JFB-over-BunnyBox incompatibility warning.
_Sidebar: drop the broken [History](_claude/HANDOFF) link, which 404'd on
every page; add the Plugins sub-pages for parity with Home.
Discord invite aligned with README.md (d8vxTZa7sU) — owner to confirm.
Wiki-RC1.04 — Fan calibration script rewrite + Calibrations.md update
- Replace assets/fan_test.py with rewritten script: interactive IP prompt,
two-phase measurement (speed-up lag + kickstart sweep), Orca Slicer output
- Rewrite Fan Timing Calibration section: remove manual IP-edit step, fix
wrong printer.cfg instruction, add Requirements block, update steps to
match new two-phase flow and correct output target (Orca, not Klipper)
- Bump WIKI_VERSION to Wiki-RC1.04
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01Muj3W5JSz3EGknPHXgcx8G
Wiki-RC1.01 - Initial wiki population (17 pages + assets)