Skip to content

Procedures Multi GPU

Jump to bottom
Consensus Protocol edited this page Jul 28, 2026 · 2 revisions

Running several cards

What this page covers. What happens when a host has more than one CMP 170HX: why shipping master works on multi-card rigs despite being a single-card installer, what the unreleased multiple-cards branch adds (per-BDF classification, the gpu_inventory file, the mixed profile and SKIP_GEOMETRY_REWRITE), and the failure modes that only appear once there are two or more GPUs in the box.

The key result up front: the unlock itself is already per-GPU. Since commit 7fe49b6 the patched nvidia.ko carries both geometries and selects one at GSP boot from pGpu->idInfo.PCIDeviceID >> 16, so every card in the machine is unlocked independently with the right size, whatever the installer thought. What is single-card on master is only the installer's bookkeeping: it takes the first matching lspci line, guesses one profile from one nvidia-smi reading, and writes one set of metadata files. The multiple-cards and Gen2 branches replace that bookkeeping with a real per-device inventory.

Multi-GPU operation is confirmed working in practice: one operator passed through eight 8 GB CMP 170 cards under Proxmox and all of them unlocked. Earlier advice for a six-card rig was to try master first, and a multi-GPU user later confirmed master worked well.

What master does on a multi-card host

lspci -nn | grep -iE '10de:20b0|10de:20c2|10de:2082' | head -1

That head -1 is the whole story. install.sh records one BDF and one device ID, then calls detect_card_profile(), which reads nvidia-smi --query-gpu=memory.total --format=csv,noheader,nounits | head -1, again taking the first entry, this time in nvidia-smi order rather than lspci order. The two orderings are not guaranteed to agree.

The consequences on current master:

Scenario Outcome
4x 8 GB cards Works. All four unlock to 65536 MiB. Profile metadata says 8gb, which happens to be right
4x 10 GB cards Works. All four unlock to 40960 MiB
Mixed 8 GB + 10 GB The geometry is still correct per card, because it is chosen by device ID at GSP boot. Only card_profile / unlock_geometry are wrong for whichever type lost the coin toss
CMP cards plus an unrelated NVIDIA GPU The profile may be detected from the other card. Still only a metadata error, unless the other card's size falls outside all four detection windows, in which case the install dies
A 10de:20b0 card is present Warned about only if it is the first matching lspci line; sitting behind a 20c2 or 2082 card the head -1 hides it entirely and no warning is printed. Either way it is never unlocked, because the in-driver gate accepts only 0x20C2 and 0x2082

!!! warning "Always pass --profile on a mixed-GPU host" A host with an RTX 3080 10 GB alongside an 8 GB CMP 170HX was reproduced by at least two people detecting "10GB" from the 3080 and selecting the 10 GB profile. A separate report has another CMP SKU (a 50HX) misdetected as a 10 GB 170HX. On current master this only mislabels the metadata files, but the habit of passing --profile=8gb or --profile=10gb explicitly costs nothing and removes a whole class of confusing output.

The multiple-cards branch

!!! warning "Experimental: unreleased branch" multiple-cards (tip b1cb6d8 "Added support for multiple cards", committed 2026-07-18, announced 2026-07-19) has not merged into master as of tip cc872cb (2026-07-23). The same installer also exists folded into the Gen2 lineage via commit 2f27474 "Gen2 + multiple-card support". Everything in this section is branch code.

Per-BDF classification

detect_card_profile() is replaced by profile_from_devid():

profile_from_devid() {
    case "$1" in
        20c2) echo "8gb" ;;
        2082) echo "10gb" ;;
        *) echo "unsupported" ;;
    esac
}

expected_mib_for_profile() {
    case "$1" in
        8gb) echo "65536" ;;
        10gb) echo "40960" ;;
        *) echo "" ;;
    esac
}

The installer then walks every line of lspci -nn | grep -iE '10de:20b0|10de:20c2|10de:2082' (via mapfile, not head -1) and builds five parallel arrays: BDF, device ID, profile, expected MiB, current MiB. Current MiB comes from a single cached nvidia-smi --query-gpu=pci.bus_id,memory.total --format=csv,noheader,nounits lookup, matched by bus ID rather than by index.

Bus IDs are compared through a shared normalize_bus_id() that lowercases and expands a short BB:DD.F into 0000:BB:DD.F, so the lspci and nvidia-smi spellings compare equal. The same function exists verbatim in verify.sh.

A 20b0 card is classified unsupported and skipped here, with GPU <bdf> (10de:20b0), unlock path not gated for this ID; skipping, which is a behavioural difference from master (which warns and continues with that card selected). If every detected card is unsupported, the branch installer dies with No unlockable CMP 170HX GPUs found (need 10de:20c2 and/or 10de:2082).

Typical step 2 output:

✓ GPU 0000:0b:00.0 (10de:20c2) → 8gb (current 8192 MiB, expect ~65536 MiB unlocked)
✓ GPU 0000:0c:00.0 (10de:20c2) → 8gb (current 8192 MiB, expect ~65536 MiB unlocked)
✓ GPU 0000:0d:00.0 (10de:2082) → 10gb (current 10240 MiB, expect ~40960 MiB unlocked)
==> Inventory: 3 unlockable (2× 8gb, 1× 10gb)

The mixed profile

When both COUNT_8GB > 0 and COUNT_10GB > 0, CARD_PROFILE becomes a third value, mixed:

✓ Mixed variants detected → profile mixed (runtime geometry by PCI ID)
==> Unlock geometry: 64GB for 20c2 / 40GB for 2082 (chosen at GSP boot per GPU)

A --profile= override is explicitly discarded on a mixed inventory, with --profile=8gb ignored for mixed inventory; card_profile stays mixed (each card unlocks by PCI ID). On a homogeneous inventory the override is honoured but warns that it is metadata only. The branch's help text makes the demotion explicit: Force 8GB metadata label (geometry is still chosen per PCI ID).

SKIP_GEOMETRY_REWRITE

driver/build.sh on the branch gains a third case and a guard flag:

SKIP_GEOMETRY_REWRITE=0
case "${PROFILE}" in
    8gb|8GB)   CFG1="0x02779000"; LMR="0x0000020B"; FB_BYTES="0x0000001000000000"; UNLOCK_LABEL="64GB" ;;
    10gb|10GB) CFG1="0x02669000"; LMR="0x0000028A"; FB_BYTES="0x0000000A00000000"; UNLOCK_LABEL="40GB" ;;
    mixed|MIXED)
        PROFILE="mixed"
        CFG1="0x02779000"; LMR="0x0000020B"; FB_BYTES="0x0000001000000000"
        UNLOCK_LABEL="mixed"
        SKIP_GEOMETRY_REWRITE=1
        ;;
esac

if [[ "${SKIP_GEOMETRY_REWRITE}" -eq 1 ]]; then
    info "mixed profile: runtime device-id geometry (no build-time CFG1/LMR rewrite)"
else
    python3 - ... <<'PY'
    ...
fi

Two things are worth noticing in that snippet:

  1. In mixed mode the CFG1 / LMR / FB_BYTES variables are still assigned the 8 GB values, and are simply never used. They are the values a mixed host would try to bake for every card if the flag were dropped and the rewrite were reachable; point 2 explains why it is not.
  2. SKIP_GEOMETRY_REWRITE is belt-and-braces on top of an existing safety net. The inline Python step it skips already begins with a six-marker check for both baked geometries and exits with runtime device-id geometry (profile metadata=<label>) without editing anything. On any tree descended from 7fe49b6 the rewrite is a no-op regardless. The flag matters only if someone re-introduces a single-SKU patch.

unlock_geometry is written as the literal string mixed in that mode, and card_profile as mixed.

The gpu_inventory file

install.sh exports CMPUNLOCKER_GPU_INVENTORY and build.sh persists it to /lib/modules/$(uname -r)/updates/cmpunlocker/gpu_inventory, one whitespace-separated line per unlockable GPU:

BDF              devid  profile  expected_mib
0000:0b:00.0     20c2   8gb      65536
0000:0c:00.0     20c2   8gb      65536
0000:0d:00.0     2082   10gb     40960

The real file has no header row; the columns above are labelled for readability. If the variable is empty, build.sh truncates the file to zero bytes rather than leaving a stale one.

Like the other three metadata files, nothing in the kernel modules reads it. Its only consumer is verify.sh, which prefers it over live lspci enumeration so that a card which has fallen off the bus is reported as MISSING rather than silently vanishing from the check.

verify.sh on a multi-card rig

sudo ./verify.sh

Enumerates from gpu_inventory if it is readable and non-empty, otherwise falls back to lspci -nn | grep -iE '10de:20c2|10de:2082'. Per GPU it prints OK, STOCK, MISSING or UNEXPECTED against the windows >= 60000 MiB (8gb) and 35000-59999 MiB (10gb), then summarises:

✓ All 3 unlockable GPU(s) report unlocked memory

or fails with <n> GPU(s) failed unlock verification. Cold reboot if modules were just installed. Full details, including the two things it does not check, are in Verify.

Known multi-card failure modes

1. depmod silently picks one nvidia.ko

The highest-value item on this page. A patched and a stock nvidia.ko can both end up under the single updates depmod search entry, in which case depmod picks one arbitrarily and silently drops the other. One tester root-caused a multi-GPU failure to exactly this, kept only the cmpunlocker variant in the updates search path, rebooted, and then confirmed multi-GPU operation working.

This is the same failure class as the srcversion mismatch that build.sh warns about: the running module is not the patched one, so no card unlocks. Diagnose it with:

modprobe -n -v nvidia | awk '/insmod/ {print $2; exit}'
find /lib/modules/$(uname -r)/updates -name 'nvidia.ko'
cat /sys/module/nvidia/srcversion
modinfo -F srcversion /lib/modules/$(uname -r)/updates/cmpunlocker/nvidia.ko

Anything not under updates/cmpunlocker/ in the first command, or more than one nvidia.ko in the second, is the bug.

2. A stale initramfs beats depmod entirely

Unchanged from the single-card case but worse in a rig, because a partial result looks like a per-card problem rather than a module-loading problem. build.sh rebuilds the initramfs itself and warns No initramfs tool found, rebuild manually before rebooting when it cannot. If some cards unlock and others do not on the same boot, this is not the cause; if none do, it very likely is.

3. Profile misdetection from the wrong GPU

Covered above. On master it is a metadata-only error, except when it makes the install die.

4. verify.sh's lspci fallback drops 0x20B0

install.sh greps 10de:20b0|10de:20c2|10de:2082 and then warns or skips 20b0, but verify.sh's fallback path greps only 10de:20c2|10de:2082. A rig containing a 20b0 card will show a different device count in the installer and in the verifier. Harmless, but confusing.

5. Virtualisation constraints

  • Proxmox passthrough works for memory and compute: eight 8 GB cards passed through and all unlocked.
  • Use SeaBIOS, not UEFI/OVMF. UEFI produces RM init and adapter failures that mimic the exploit simply not working. This was root-caused first-hand and immediately corroborated by a second person whose non-reproductions turned out to have the same cause.
  • PCIe Gen2 link training does not work in a VM as of 2026-07-24, acknowledged by the maintainer as an open debugging item.

6. Host-level wedges in multi-tenant use

One operator's renter killed an underperforming llama.cpp run (about 121 t/s) and left ghost processes that wrecked the driver state. Recovery required a host reboot by the operator, because the cards could not be restarted from inside the Docker container. Plan for out-of-band reboot access on any rented rig. See Recovery.

7. Interconnect, not installer

Several "multi-card is slow" reports are link-bandwidth problems, not unlock problems:

  • Every card is Gen1 x4 by default. Going to Gen2 is a software change on unreleased branches; going beyond x4 width requires soldering AC-coupling capacitors. These are two entirely separate achievements. See PCIe subsystem and PCIe Gen2.
  • NVLink is fused off and P2P is absent on this card. llama-server --split-mode row was circulated alongside the layer-split command but annotated "benchmark-only on these links", consistent with tensor-parallel-style splits not being viable at Gen1 x4.
  • A frequently quoted rule of thumb ("x4 gives 10-30% speedup, x8 or better is ideal" for multi-GPU LLM serving) was offered as a rule of thumb and was not measured on a 170HX. Treat it as low confidence. See LLM inference.

8. P2P layering

The aikitoria P2P patch can be layered on top of cmpunlocker by dropping its diff into driver/patches/ as 0007-unlock-p2p.patch, because build.sh applies every *.patch in glob order. Whether it does anything useful on a 170HX-only system is unresolved: one tester reported "It doesn't seem to take effect on the 170HX... It only has an effect on them if there are other models of GPUs on the same machine", while another reported P2P plus cmpunlocker working on the same day in a rig that also contained two RTX 3090s, which is precisely the mixed-model case the first report says is the only one that works. Both sides agree P2P is bandwidth-bound and of little benefit at Gen1 x4. See P2P.

Recommended procedure for a multi-card rig today

  1. Inventory the hardware before installing anything:

    lspci -nn | grep -iE '10de:20b0|10de:20c2|10de:2082'
nvidia-smi --query-gpu=pci.bus_id,name,memory.total --format=csv

    Confirm the device ID of every card. See Identify your card.

  2. Install from master with an explicit profile if all cards are the same type:

    sudo ./install.sh --profile=8gb     # or --profile=10gb

    For a genuinely mixed 8 GB + 10 GB rig, master still produces correct geometry per card; the only thing you give up is accurate metadata and verify.sh. If you want those, use the multiple-cards branch and accept that it is unreleased.

  3. Cold boot. sudo shutdown -h now, then power on.

  4. Verify every card individually, not just the first:

    nvidia-smi --query-gpu=pci.bus_id,memory.total --format=csv
sudo dmesg | grep 'POST-WRITE'      # one line per unlocked GPU, with its devId

    The POST-WRITE line carries (devId=0x...), so a rig with mixed SKUs should show both CFG1=0x02779000 LMR=0x0000020b and CFG1=0x02669000 LMR=0x0000028a lines.

  5. If exactly one card is wrong, suspect that card (seating, power, riser). If all are wrong, suspect module loading (failure modes 1 and 2).

Merge status

!!! question "Open problem: should multi-card, IOMMU and Gen2 merge to master, and in what order?" Neither multiple-cards (b1cb6d8, standalone) nor the Gen2 lineage (which folds it in) has merged as of cc872cb. The obstacle is bundling: merging Gen2 wholesale would drag the experimental PCIe link retraining patches (0007-pcie-gen2.patch, 0008-pcie-gen2-probe-retrain.patch) and their unverified register writes into the stable path. The multi-card installer changes are self-contained and could be cherry-picked alone, and the mixed profile already works because master's patch 0001 bakes in both geometries. Separately, clanker/driver-port (580/590/595/610 support) and the Gen2 lineage were developed independently and never merged, so choosing one today means giving up the other. See Status board and Driver versions.

Related pages

Home

Start

Hardware

Unlock

Procedures

Operations

Frontier

History

Appendix

Clone this wiki locally