docs(wiki): v2.14.00 multi-board release - Classic CYD and WS-C5-28 promoted to fully supported
Home.md: new "Supported Hardware" section (NM-CYD-C5 primary/preferred,
Classic CYD supported, Waveshare WS-C5-28 supported/new), updated intro,
"What's New" bumped to v2.14.00 with a multi-board-support headline.
New page: Waveshare-WS-C5-28-Support.md - hardware differences from
NM-CYD-C5, the CH32V003 IO expander architecture, RF-HAT wiring, flash
instructions, known issues.
Where-To-Get-It.md: board selector mention, corrected + expanded manual
flash instructions for all three boards (was NM-CYD-C5-only, and had a
stale wrong bootloader offset), purchase info for Classic CYD and
WS-C5-28.
Getting-Started.md: board selector mention, flagged the resistive-touch
section (Sec 3) and RF-HAT enablement (Sec 4) as NM-CYD-C5/Classic-CYD-
specific where WS-C5-28 differs (capacitive touch, no calibration; RF-HAT
needs manual wiring not plug-and-play).
docs(wiki): v2.13.43 comprehensive feature documentation
BLE-Research.md:
- Add BLE Tracker Detection section (AirTag/SmartTag/Tile protocol
details, GATT-confirmed ring auth, cross-session tracking)
- Add Passive Observation System (OBS) section: 8 classifiers,
Passive Log UI, recurrence detection, JSONL at /sdcard/lab/obs/
WiFi-Security-Research.md:
- Add WiFi Frame Capture + BLE Targeted PCAP (v2.12.3)
Wardriving.md:
- Add Radio Mode NVS Persistence (v2.12.1)
- Add GPS Serial Debug Toggle (v2.13.5)
Getting-Started.md:
- Add Go Dark covert operating mode section (full-screen 5s touch-to-wake)
Contributors.md, Support-and-Community.md:
- Fix @birolt29 attribution (remove bare name, fix capitalisation)
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
docs: update SD Assets repo URL after rename CYM-NM28C5-SD-Assets → CYM-SD-Assets
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
docs: update GitHub URLs after repo rename CYM-NM28C5 → CYM
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
docs: fix GPS VCC voltage guidance — ATGM336H accepts 3.3V or 5V via onboard LDO
docs: Valleytech review first-run UX docs pass (YT-001/003/006/E002/E003)
New: Getting-Started.md — comprehensive first-run guide covering:
- Resistive touch behavior and the red dot (YT-001/002)
- SD card provision: full folder layout, what the Validate & Provision
action creates, SD Asset Repository pointer (YT-003/004)
- RF-HAT enablement checklist: how to enable, DIP switch map, module
status table for all 5 modules in v2.12.x (YT-007/008)
- GPS wiring: LP-UART pin map, serial settings, baud auto-detect,
troubleshooting table (YT-E002/E003)
- WiFi tool naming explainer: Channel Analyzer vs WiFi Band Scope (YT-006)
- Wardrive categorization note (YT-005)
Updated: Home.md
- Add Getting Started link at top of the getting-started section with
"First-time setup" descriptor so it is the most visible entry point.
Updated: WiFi-Security-Research.md
- Rename "Chanalizer" to "Channel Analyzer" throughout.
- Add WiFi Band Scope section: description, feature comparison table vs
Channel Analyzer, and two research use cases. (YT-006)
Updated: Where-To-Get-It.md
- Expand GPS module section with full wiring table (TX/RX/VCC/GND),
voltage warning, baud default, and link to Getting-Started GPS guide. (YT-E002)