Skip to content

Releases

MPC 600 S, LA Version 1.6

Choose a tag to compare

@LA-2500 LA-2500 released this 18 Nov 00:53

Fix: long samples cutting out on the second pass. A note longer than the loop (MPC 2500 projects often have them) left its release waiting into the next pass, where it cut off the pad's new note in the last bars. A new note on a pad now takes over that pad's release (MIDI notes too).

Fix: the main volume cutting out. A dropout reading of 0 sent twice in a row could silence the output until the knob was touched. The main volume now needs two confirming readings for a jump; a real turn still follows at once.

Save/Load (from v1.5):

  • Opens on the Mode and Type used last (after loading an MPC 2500 PROJECT: LOAD, MPC 2500 PROJECT).
  • LOAD has two pages: Mode, Type, Into and Clear all, then B3 for the files, worked like Load Files (the wheel moves the bar, pushing it or B3 opens or loads, B1 goes up).
  • Delete is SHIFT + B2 (asks first). Clear all (NO / YES) empties memory before a load, asking first.

Install: extract MPC-600-S-OS-v1.6.zip and replace the autorun folder on the card. Your saved work, in MPC600S, is untouched.

MPC 600 S, LA Version 1.5

Choose a tag to compare

@LA-2500 LA-2500 released this 17 Nov 23:34

Fix: the screen jumping while turning knobs or using the data wheel. Turning K1–K3, the slider or the main volume, or turning or pushing the data wheel, presses on the panel, and the pads near them could send light hits of their own. On an editing page such a hit selected another pad, so the page jumped to its sample. (1.4 caught these only right after a real pad hit.)

  • For 300 ms after a knob, slider or wheel movement, and while the wheel is held down, pad hits lighter than velocity 48 are ignored. Firm presses still play.
  • The 1.4 rule for neighbouring pads stays.
  • If pads still play by themselves, raise Pad Thresh in Additional Settings.

Save/Load:

  • SHIFT + Pad 16 opens Save/Load on the Mode and Type used last: after loading an MPC 2500 PROJECT it opens on LOAD, MPC 2500 PROJECT. The first time after power-on, SAVE PROJECT.
  • LOAD has two pages: first Mode, Type, Into and Clear all, then B3 opens the files, which work like Load Files: the wheel moves the bar, pushing the wheel (or B3) opens a folder or loads the item, B1 goes up a folder.
  • On the files page, B2 renames; Delete is SHIFT + B2, so it can't be pressed by accident. It still asks first.
  • LOAD: new Clear all field (NO / YES). With YES, Load asks "Clear all, then load?", empties every program, sound, sequence and song (settings stay), then loads. It goes back to NO after each use.

Install: extract MPC-600-S-OS-v1.5.zip and replace the autorun folder on the card. Your saved work, in MPC600S, is untouched.

MPC 600 S, LA Version 1.6C

Choose a tag to compare

@LA-2500 LA-2500 released this 18 Nov 18:45

Fixed: browsing sounds on the Sample: field. Turning the wheel now steps through every sound in memory, in a fixed order, both ways. Before, with sounds in memory that weren't on a pad, it went back and forth between two.

  • Stems: the result line no longer shows "0bit".

Everything in v1.6B is included (USB Audio Out, Save/Load, long samples no longer cut on the next pass).

Install: extract MPC-600-S-OS-v1.6C.zip and replace the autorun folder on the card. Your saved work, in MPC600S, is untouched.

MPC 600 S, LA Version 1.6B

Choose a tag to compare

@LA-2500 LA-2500 released this 18 Nov 03:31

New: USB Audio Out. Connected to a computer by USB, the MPC 600 S is an audio input on the computer (44.1 kHz stereo, no driver). It sends the full master mix: pads and sequences, the track mixer with its EQ, sends and inserts, Input Thru, and Master Effects. It's taken after Master Effects and before the main volume, so a recording doesn't change with the volume knob. The MPC follows the computer's clock on its own.

  • Choose the MPC as the input in your recording software, with USB Audio Out ON.
  • Switch it on with USB Audio Out on Additional Settings (OFF to start).
  • With Input USB and Input Thru on, you hear the computer's audio on the MPC's phones and line out, but it is never sent back to the computer: no loop, no doubled track.

Everything in v1.6 is included (long samples no longer cut on the next pass, main volume dropouts, Save/Load).

Install: extract MPC-600-S-OS-v1.6B.zip and replace the autorun folder on the card. Your saved work, in MPC600S, is untouched.

MPC 600 S, LA Version 1.4

Choose a tag to compare

@LA-2500 LA-2500 released this 17 Nov 16:57

Fix: pads playing by themselves next to the pad you hit. A hit shakes the pads around it, and they could send light hits of their own, even with light or moderate playing. On an editing page, such a hit also selected that pad, so the screen jumped to another pad's sample (your edits stayed on the pad you were editing).

  • A hit on a neighbouring pad (beside it or at a corner) within 40 ms of a press, under 60% of its velocity, is now taken as the panel shaking and ignored.
  • On pads further away only much lighter hits are ignored, so two pads played together still both play.
  • If pads still play by themselves, raise Pad Thresh in Additional Settings (1 to 60, default 12).

Install: extract MPC-600-S-OS-v1.4.zip and replace the autorun folder on the card. Your saved work, in MPC600S, is untouched.

MPC 600 S, LA Version 1.3

Choose a tag to compare

@LA-2500 LA-2500 released this 16 Nov 03:09

New: other MPCs' files, both ways. Save/Load reads what an MPC 1000, MPC 2500 or MPC 500 saves, and writes projects an MPC 2500 loads.

  • MPC 2500 SEQUENCE loads a sequence from an .ALL file (all of an MPC's sequences together) or a .SEQ (one on its own). Choose the sequence, then its tracks: they go onto the first empty tracks of the sequence on Into, nothing already there touched. Drum notes go back onto the pads they were played on, by the program file beside the .ALL; each track plays its own MPC program if it is loaded. An empty sequence takes the file's tempo (to the tenth of a BPM), time signature and length, and loops to bar 1. The MPC runs at 96 PPQN, as the MPC 600 S does, so notes land on exactly the same ticks.
  • MPC 2500 PROGRAM loads a .PGM with its samples (the WAVs beside it, or a folder down or up): each pad's sample with its start, end and loop points, level, pan, tuning, play mode, mute group, envelope and filter. The message says how many WAVs were not found.
  • MPC 2500 PROJECT loads a .PRJ whole, into what is empty: every program, then every sequence, each track on its own program. MPC 1000 and MPC 500 projects load too.
  • MPC 2500 PROJECT on SAVE writes the project as a folder an MPC 2500 loads: the .PRJ, ALL_SEQS&SONGS.ALL (every sequence in its own number, up to 64 tracks), a .PGM for each program (pads A01-D16 and their settings), and every sample as a 16-bit 44.1 kHz WAV with its start and end. Pads in banks E-H and tracks past 64 are left out, and the message says how much.
  • MIDI FILE loads a Standard MIDI File the same way: tracks chosen, onto the first empty tracks; SHIFT + push makes a track DRUM or KEYS.
  • SEQUENCE saves and loads one sequence on its own, with all its tracks.
  • Each MPC has its own types, named for it: these are for the MPC 2500, and read the MPC 1000's and MPC 500's files too, which are the same.
  • The MPC types open at the top of the card, where an MPC's folders go. Each type remembers its folder and last item until power-off, so loading one after another stays put. B1 is out of a folder.

Knob Mode (Additional Settings 2): how K1-K3 and the slider take over a value. CATCH (as before: nothing moves until the knob reaches the value), JUMP (straight to the knob), SCALE (from where it is, meeting the knob at the ends).

Timing Correct knobs: K1 Swing (the SP12's six settings in SP12 mode), K2 Shift amount, K3 the Move Existing track.

Also: SHIFT + MUTE unmutes every track. SHIFT + ERASE opens Program Config with Copy started on the last pad pressed. Resample Start defaults to THRESHOLD; FORCE is now MANUAL. 16 Levels Tune's root starts on A08, so the pads play seven semitones down to eight up on bank A.

Install: extract MPC-600-S-OS-v1.3.zip and replace the autorun folder on the card. Your saved work, in MPC600S, is untouched.

MPC 600 S, LA Version 1.2

Choose a tag to compare

@LA-2500 LA-2500 released this 14 Nov 15:24

New: S600 MULTI, multisample instruments. A third program Type (MPC, S600, S600 MULTI). One pad, the Instrument (Inst in Program Config), plays samples from the program's pads across the keyboard: up to 32 keygroups, each with two velocity zones, its root, tuning, level and pan; shared S600 envelopes, filter and LFO; key tracking (KEY>PAN, KEY>FILTER, KEY>LEVEL, KEY>ENV) with instrument templates. A keyboard view on the Keygroup page, K1 through the keygroups, keys and pads to set roots, ranges and zones.

Auto Sampler: play each note asked for ("Ready for Sample 1, Velocity 1"); , , ; at the end each sample's pitch is detected and everything is mapped by pitch and velocity, onto pads in pitch order. 12-bit mono at 29.76 kHz to start.

Auto Map builds the keygroups from the pads, the roots from file names and pitch detection; Root Auto-Detect gives S600 sounds their root note when loaded, so MIDI keys play them at true pitch. S600 programs get an Instrument too (A01, or LAST PAD).

S600 Mod page (B2: Filter, LFO, Mod): the mod wheel on pitch (vibrato), filter (LFO movement, or OPEN: the cutoff opened) and level (tremolo), and the pitch bend range. The Main page: Poly, Legato, Portamento, Note On, Root Note (Auto-Detect).

Insert effects (mixer: SHIFT + B3 FX Sends, then SHIFT + B3 again): effects in any track's channel, in series before its fader, pan and sends. 8 insert slots shared across all tracks, each effect using what it costs (reverbs 4, amps, delays and modulation 2, EQs, dynamics and drives 1), with a live CPU meter. Saved with the project and included in exports.

All On envelope template, the new default for S600 sounds: full level from note start until release.

Zone Assign TRANSIENT (CHOP): a zone at every drum hit of a break, found at once: kicks, snares, hats and ghost notes, each zone starting just before its hit. Sensitivity 1-10, starts movable a millisecond at a time, for a false hit.

Loading a program asks first, naming the program it goes into (the wheel picks another; loads into the first empty program).

New: Live Looper. On Audiotrack Record, B2 : one-pass takes drop onto pads while the sequence keeps looping. Layer take after take without stopping; removes the last one. Live Loop Conversion (Additional Settings 2): IMMEDIATE converts during the pass, so the take drops in a few ms after it; AFTER 1ST LOOP drops in the raw take and converts while it plays, suited to longer takes.

Footswitch AUDIO REC (MIDI Settings, Sustain: FOOTSWITCH): the pedal is / on Audiotrack Record and Live Looper, and on any page once Live Looper takes have started.

Footswitch setup (MIDI Settings): Foot Chn (ANY to start, so any keyboard's pedal works), Foot CC (64 to start) and Polarity (AUTO works out a pedal that rests "down"; or NORMAL, INVERTED). sets all three from one press of the pedal, and the bottom line shows what the pedal last sent.

Additional Settings on two pages. Page 2 holds Loop Conv and the start values for every recording page: Sample Rate (29.76 kHz; the slider's rates, or SET to any rate), Bit Rate (12), Anti-Aliasing and Normalize (on), Input Thru (always on, or off) and Rec Mode (stereo; Convert Sample stays mono).

Metronome: Audio Rec (click during audio track and Live Looper takes, default NO) and After Loop (click after a Live Looper take, default STOP).

SAMPLE + pad selects a pad without playing it in every mode (Note Repeat, Local Mode off, MIDI tracks): set a loop's volume without retriggering it.

Fixed: Master Effects are no longer kept in the settings file: they start off at power-on unless the Autoload project has them.

Install: extract MPC-600-S-OS-v1.2.zip and copy the autorun folder to the SD card root, replacing the old one. Your MPC600S folder is kept.

MPC 600 S, LA Version 1.1

Choose a tag to compare

@LA-2500 LA-2500 released this 13 Nov 20:11

Download mpc-os.zip, unzip it, and copy the autorun folder to the top of an SD card. The Quick Start guide has the steps; the manual covers everything. The stems models are optional, only for the Stems page.