solutions: ref-designs: Added AD-MAX32SXWISE-SL Page and sub-pages

docs/solutions/reference-designs/ad-max32lrwise-sl/ev-cattletag-ardz/index.rst

@@ -54,28 +54,27 @@
 ^^^^^^^^^^^^
 
 When using the board, the power supply may come from different sources,
 and these are listed below:
 
 .. figure:: ev-cattletag-ardz_power_supply_input.png
 
 - **Solar Panel** - use to recharge the lithium-ion connected to either P8 or to the
   2x AAA battery. An example of a probe that can be used is a product from
   AnySolar and its datasheet can be found
   `here <https://waf-e.dubudisk.com/anysolar.dubuplus.com/techsupport@anysolar.biz/O18Ae08/DubuDisk/www/Gen3/KXOB25-14X1F%20DATA%20SHEET%20202007.pdf>`__.
 - **P6 Terminal block** - external power source (e.g., solar panel)
 
 .. note:: When using an external power source, it is required to
       disconnect the on-board solar panel by removing the resistor **R30**.
 
 .. figure:: ev-cattletag-ardz_solar_panel_option.png
 
-- **P8 Terminal block** - external power supply, between 3V to 4.2V allowable
-  input
+- **P8 Terminal block** - external power supply, between 3V to 4.2V allowable input
 - **Battery holder** - 2xAAA battery is required.
 - **Arduino Power** - external power supply that comes directly from the host board
   it is connected to.
 
 .. note:: When power supply directly from the host board is used, it is
       required to remove the **R84** resistor and placed a 0Ω resistor at **R86**.
 
 .. figure:: ev-cattletag-ardz_power_source_option.png
@@ -86,7 +85,7 @@
 The Arduino interface is a standardized digital interface for various digital
 communication protocols such as SPI, I2C, and UART. These interface types were
 standardized by Arduino, which is hardware and software company. Complete
 details on the PMOD specification can be found
 `here <https://www.arduino.cc/en/hardware>`__.
 
 The pin map for the Arduino pins is described in the table and its schematic
@@ -128,7 +127,7 @@
 - One (1) MAX32625PICO Rapid Development Platform with 10-pin ribbon cable
   with firmware image:
   `MAX32625PICO Firmware Image for MAX32670 <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
-- One (1) CR123A Battery or any equivalent external DC power supply (+3V to +4.7V)
+- One (1) CR123A Battery or any equivalent external DC power supply (+3V to +4.7V).
   **Note that this is not included in the kit**
 - One (1) Micro USB to USB cable
 - Host PC (Windows 10 or later)
@@ -161,8 +160,7 @@
 
 #. Download the firmware image: `MAX32625PICO Firmware Image for
    MAX32670 <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
-#. Do not connect the MAX32625PICO to the
-   :adi:`MAX32670-LR-ARDZ` Base Board yet.
+#. Do not connect the MAX32625PICO to the :adi:`MAX32670-LR-ARDZ` Base Board yet.
 #. Connect the MAX32625PICO to the Host PC using the micro USB to USB cable.
 #. Press the button on the MAX32625PICO. **(Do not release the button until the
    MAINTENANCE drive is mounted)**.

docs/solutions/reference-designs/ad-max32lrwise-sl/index.rst

@@ -195,11 +195,11 @@ Equipment Needed
 - One (1) :adi:`MAX32670-LR-ARDZ` Base Board
 - One (1) :adi:`EV-CATTLETAG-ARDZ` Sensor Node
 - One (1) MAX32625PICO Rapid Development Platform with 10-pin ribbon cable
-  with firmware image: max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin
-- One (1) CR123A Battery or any equivalent external DC power supply (+3V to +4.7V)
-  ** Note that this is not included in the kit**
+  with `firmware image <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
+- One (1) CR123A Battery or any equivalent external DC power supply (+3V to +4.7V).
+  **Note that this is not included in the kit**
 - One (1) Micro USB to USB cable
--  Host PC (Windows 10 or later)
+- Host PC (Windows 10 or later)
 
 .. figure:: hardware_setup.png
 
@@ -251,14 +251,18 @@ Equipment Needed
 
    .. figure:: max32670-lr-ardz_to_maxpico.png
 
-Once you have completed this setup, proceed to PHASE 2 found in
-ADI Long Range Wireless Radio Software User Guide.
+**Once you have completed this setup, proceed to PHASE 2 found in**
+:dokuwiki:`ADI Long Range Wireless Radio Software User Guide </resources/eval/user-guides/longrangewirelessradio/software>`.
 
 Resources
 ---------
 
-- MAX32670-LR-ARDZ Base Board User Guide
-- EV-CATTLETAG-ARDZ Sensor User Guide
+.. toctree::
+   :titlesonly:
+   :maxdepth: 1
+   :glob:
+
+   */index
 
 FAQs
 ----
@@ -290,10 +294,3 @@ Help and Support
 
 For questions and more information about this product, connect with us through
 the :ez:`Analog Devices Engineer Zone </>`.
-
-.. toctree::
-   :titlesonly:
-   :maxdepth: 1
-   :glob:
-
-   */index

docs/solutions/reference-designs/ad-max32sxwise-sl/ev-flowmeter-ardz/index.rst

@@ -0,0 +1,223 @@
+.. _ev-flowmeter-ardz:
+
+EV-FLOWMETER-ARDZ
+=================
+
+Sensor for Flow Rate Metering
+"""""""""""""""""""""""""""""
+
+Overview
+--------
+
+The :adi:`EV-FLOWMETER-ARDZ` sensor is an advanced and efficient solution 
+for flow measurement, suitable for utility and industrial applications. 
+The ultrasonic time-of-flight technology, coupled with the integrated functions 
+of the :adi:`MAX35101` time-to-digital converter, addresses the limitations of 
+mechanical flow meters and offers improved accuracy and longevity.
+
+.. figure:: ev-flowmeter-ardz_angle.png
+   :width: 600 px
+
+Features
+~~~~~~~~
+
+- High accuracy flow measurement for billing and leak detection
+- Time-to-digital accuracy down to 20 ps
+- Measurement range up to 8 ms
+- Two (2) single-stop channels
+- High accuracy temperature measurement for precise heat and flow calculations
+- Up to four (4) 2-wire sensors
+- PT1000 and PT500 RTD support
+- Maximizes battery life with low device and overall system power
+- Low 10 μA ToF measurement and <125 nA duty-cycled temperature measurement
+- Event-timing mode reduces host microcontroller
+
+Applications
+~~~~~~~~~~~~
+
+- Ultrasonic heat meters
+- Ultrasonic water meters
+- Ultrasonic gas meters
+- Utility metering
+- Environmental monitoring
+
+Block Diagram
+~~~~~~~~~~~~~~
+
+.. figure:: ev-flowmeter-ardz_block_diagram.png
+
+Hardware Design
+---------------
+
+Components and Connections
+~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Peripheral Connectors
+^^^^^^^^^^^^^^^^^^^^^
+
+The following standard connectors are provided on the board for
+customer to use:
+
+- Launch up and down ultrasonic sensor terminal block headers
+- PT1000/500 platinum resistive temperature detectors (RTD) terminal block
+  headers
+- Arduino connector
+
+.. figure:: ev-flowmeter-ardz_peripherals_connections.png
+
+Sensor Probe
+^^^^^^^^^^^^
+
+When using this Arduino board, a general-purpose ultrasonic flow
+rate sensor can be used. An example of a probe is the Flow Transducer with Pipe
+(Model：HS0003) from Audiowell Sensor Technology, as shown below:
+
+.. figure:: flow_transducer_with_pipe.jpg
+
+========================= ==================
+                          **Specifications**
+Resonant Frequency        975 ±30 kHz
+Resonant Impedance        ≤ 110 Ω
+Static capacitance        1350 ±20% pF
+Pressure Resistance       1.6 Mpa
+Permanent Flowrate        2.5 m³/h
+Max Flowrate              5.0 m³/h
+Min Flowrate              0.050 m³/h
+Environmental Temperature +5°C ~ +55°C
+Diameter                  DN20
+========================= ==================
+
+For temperature measurement, this board supports up to two 2-wire PT1000/500
+platinum resistive temperature detectors (RTD) and the connections can be seen
+on the diagram as shown below: <note important>An RTD sensors or a dummy sensor
+(1k Resistor) for each terminal are required in order to run and capture the
+flow rate. </note>
+
+.. figure:: ev-flowmeter-ardz_probe_connections.png
+
+Digital Interface (Arduino)
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+The Arduino interface is a standardized digital interface for
+various digital communication protocols such as SPI, I2C, and UART. These
+interface types were standardized by Arduino, which is a hardware and software
+company. Complete details on the PMOD specification can be found
+`here <https://www.arduino.cc/en/hardware>`__.
+
+.. figure:: ev-flowmeter-ardz_digital_interface.png
+   :width: 600 px
+
+Push Button
+^^^^^^^^^^^^
+
+The board provides a button, **S1**, to test tamper detection
+through its CMOS digital input.
+
+.. figure:: ev-flowmeter-ardz_reset_button.png
+   :width: 600 px
+
+Applications
+------------
+
+The :adi:`EV-FLOWMETER-ARDZ` can be used with the :adi:`MAX32670-SX-ARDZ` Base Board,
+which is a long-range wireless radio development platform based on MAX32670
+ultralow power Arm Cortex-M4 microcontroller and SX1261 RF transceiver.
+
+Using these platforms together enables users to design solutions based on
+low-power, long range proprietary radio communication technique that is
+suitable for customized heat/flow meters.
+
+To learn more about the Long Range Wireless Radio solution developed by Analog
+Devices, visit the AD-MAX32SXWISE-SL Long Range Wireless Radio Development
+Kit User Guide.
+
+System Setup
+------------
+
+PHASE 1: Hardware Setup
+~~~~~~~~~~~~~~~~~~~~~~~
+
+Note that this setup only applies for MAX32670-SX-ARDZ Base Board. Users may use
+a different base board or microcontroller, however the firmware built for this
+demo application cannot be used as this is specifically designed for the
+MAX32670-SX-ARDZ.
+
+Equipment Needed
+^^^^^^^^^^^^^^^^
+
+- One (1) :adi:`MAX32670-SX-ARDZ` Base Board
+- One (1) :adi:`EV-FLOWMETER-ARDZ` Sensor Node
+- One (1) MAX32625PICO Rapid Development Platform with 10-pin ribbon cable
+  with `firmware image <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
+- One (1) CR123A Battery or any equivalent external DC power supply (+3V to +4.7V).
+  **Note that this is not included in the kit**
+- One (1) Micro USB to USB cable
+- Host PC (Windows 10 or later)
+
+.. figure:: hardware_setup.png
+
+#.  Insert one CR123A battery (3V to 4.7V) into the battery holder 
+    (BT1 connector) of the :adi:`MAX32670-SX-ARDZ` Base Board.
+
+    **Make sure to check for the battery polarity in
+    the BT1 connector, refer to the figure below. The DS3 LED will light up
+    indicating that you have inserted the battery correctly and that power is
+    provided in the base board.** 
+
+    .. figure:: base_board_with_battery.png
+
+#. Connect the :adi:`EV-FLOWMETER-ARDZ` Sensor Node to the :adi:`MAX32670-SX-ARDZ` 
+   Base Board by aligning the corresponding Arduino headers on each board.
+#. Connect the :adi:`MAX32625PICO` programming adapter to the :adi:`MAX32670-SX-ARDZ` 
+   Base Board through the 10-pin ribbon cable.
+
+   .. tip::
+
+      Make sure that the MAX32625PICO programming adapter has been flashed with
+      the correct image before connecting it to the MAX32670-SX-ARDZ Base
+      Board.
+
+**How to flash the firmware image in the MAX32625PICO**
+
+#. Download the firmware image:
+   `MAX32625PICO Firmware Image for MAX32670 <https://github.com/analogdevicesinc/max32625pico-firmware-images/raw/master/bin/max32625_max32670evkit_if_crc_swd_v1.0.3.bin>`__
+#. Do not connect the MAX32625PICO to the :adi:`MAX32670-SX-ARDZ` Base Board yet.
+#. Connect the MAX32625PICO to the Host PC using the micro USB to USB cable.
+#. Press the button on the MAX32625PICO. **(Do not release the button until the
+   MAINTENANCE drive is mounted)**.
+#. Release the button once the MAINTENANCE drive is mounted.
+#. Drag and drop (to the MAINTENANCE drive) the firmware image.
+#. After a few seconds, the MAINTENANCE drive will disappear and be replaced by
+   a drive named DAPLINK. This indicates that the process is complete, and the
+   MAX32625PICO can now be used to flash the firmware of the
+   :adi:`MAX32670-SX-ARDZ` Base Board.
+#. Connect the :adi:`MAX32625PICO` programming adapter to the
+   Host PC using the micro USB to USB cable. 
+
+   .. figure:: max32670-sx-ardz_to_maxpico.png
+
+Once you have completed this setup, proceed to PHASE 2 found in
+:dokuwiki:`ADI Long Range Wireless Radio Software User Guide </resources/eval/user-guides/longrangewirelessradio/software>`.
+
+Resources
+---------
+
+- :adi:`MAX3501 Product Page <MAX35101>`
+
+Design and Integration Files
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+.. admonition:: Download
+
+   :download:`EV-FLOWMETER-ARDZ Design Support Package Rev. A <ev-flowmeter_ardz-designsupport.zip>`
+
+   - Schematic
+   - Bill of Materials
+   - Layout
+   - Fabrication Files
+
+Help and Support
+~~~~~~~~~~~~~~~~
+
+For questions and more information about this product, connect with us through
+the :ez:`Analog Devices Engineer Zone </>`.