[pull] master from torvalds:master

Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt

@@ -161,7 +161,7 @@ The regulator node houses sub-nodes for each regulator within the device. Each
 sub-node is identified using the node's name, with valid values listed for each
 of the PMICs below.
 
-pm8005:
+pm8004:
 	s2, s5
 
 pm8005:

Documentation/hwmon/adm1177.rst

@@ -20,8 +20,7 @@ Usage Notes
 -----------
 
 This driver does not auto-detect devices. You will have to instantiate the
-devices explicitly. Please see Documentation/i2c/instantiating-devices for
-details.
+devices explicitly. Please see :doc:`/i2c/instantiating-devices` for details.
 
 
 Sysfs entries

arch/arm64/mm/context.c

@@ -260,14 +260,26 @@ asmlinkage void post_ttbr_update_workaround(void)
 			CONFIG_CAVIUM_ERRATUM_27456));
 }
 
-static int asids_init(void)
+static int asids_update_limit(void)
 {
-	asid_bits = get_cpu_asid_bits();
+	unsigned long num_available_asids = NUM_USER_ASIDS;
+
+	if (arm64_kernel_unmapped_at_el0())
+		num_available_asids /= 2;
 	/*
 	 * Expect allocation after rollover to fail if we don't have at least
 	 * one more ASID than CPUs. ASID #0 is reserved for init_mm.
 	 */
-	WARN_ON(NUM_USER_ASIDS - 1 <= num_possible_cpus());
+	WARN_ON(num_available_asids - 1 <= num_possible_cpus());
+	pr_info("ASID allocator initialised with %lu entries\n",
+		num_available_asids);
+	return 0;
+}
+arch_initcall(asids_update_limit);
+
+static int asids_init(void)
+{
+	asid_bits = get_cpu_asid_bits();
 	atomic64_set(&asid_generation, ASID_FIRST_VERSION);
 	asid_map = kcalloc(BITS_TO_LONGS(NUM_USER_ASIDS), sizeof(*asid_map),
 			   GFP_KERNEL);
@@ -282,8 +294,6 @@ static int asids_init(void)
 	 */
 	if (IS_ENABLED(CONFIG_UNMAP_KERNEL_AT_EL0))
 		set_kpti_asid_bits();
-
-	pr_info("ASID allocator initialised with %lu entries\n", NUM_USER_ASIDS);
 	return 0;
 }
 early_initcall(asids_init);

drivers/hwmon/adt7462.c

@@ -413,7 +413,7 @@ static int ADT7462_REG_VOLT(struct adt7462_data *data, int which)
 			return 0x95;
 		break;
 	}
-	return -ENODEV;
+	return 0;
 }
 
 /* Provide labels for sysfs */

drivers/hwmon/pmbus/xdpe12284.c

@@ -18,6 +18,59 @@
 #define XDPE122_AMD_625MV		0x10 /* AMD mode 6.25mV */
 #define XDPE122_PAGE_NUM		2
 
+static int xdpe122_read_word_data(struct i2c_client *client, int page, int reg)
+{
+	const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+	long val;
+	s16 exponent;
+	s32 mantissa;
+	int ret;
+
+	switch (reg) {
+	case PMBUS_VOUT_OV_FAULT_LIMIT:
+	case PMBUS_VOUT_UV_FAULT_LIMIT:
+		ret = pmbus_read_word_data(client, page, reg);
+		if (ret < 0)
+			return ret;
+
+		/* Convert register value to LINEAR11 data. */
+		exponent = ((s16)ret) >> 11;
+		mantissa = ((s16)((ret & GENMASK(10, 0)) << 5)) >> 5;
+		val = mantissa * 1000L;
+		if (exponent >= 0)
+			val <<= exponent;
+		else
+			val >>= -exponent;
+
+		/* Convert data to VID register. */
+		switch (info->vrm_version[page]) {
+		case vr13:
+			if (val >= 500)
+				return 1 + DIV_ROUND_CLOSEST(val - 500, 10);
+			return 0;
+		case vr12:
+			if (val >= 250)
+				return 1 + DIV_ROUND_CLOSEST(val - 250, 5);
+			return 0;
+		case imvp9:
+			if (val >= 200)
+				return 1 + DIV_ROUND_CLOSEST(val - 200, 10);
+			return 0;
+		case amd625mv:
+			if (val >= 200 && val <= 1550)
+				return DIV_ROUND_CLOSEST((1550 - val) * 100,
+							 625);
+			return 0;
+		default:
+			return -EINVAL;
+		}
+	default:
+		return -ENODATA;
+	}
+
+	return 0;
+}
+
 static int xdpe122_identify(struct i2c_client *client,
 			    struct pmbus_driver_info *info)
 {
@@ -70,6 +123,7 @@ static struct pmbus_driver_info xdpe122_info = {
 		PMBUS_HAVE_TEMP | PMBUS_HAVE_STATUS_TEMP |
 		PMBUS_HAVE_POUT | PMBUS_HAVE_PIN | PMBUS_HAVE_STATUS_INPUT,
 	.identify = xdpe122_identify,
+	.read_word_data = xdpe122_read_word_data,
 };
 
 static int xdpe122_probe(struct i2c_client *client,

drivers/perf/arm_pmu_acpi.c

@@ -24,8 +24,6 @@ static int arm_pmu_acpi_register_irq(int cpu)
 	int gsi, trigger;
 
 	gicc = acpi_cpu_get_madt_gicc(cpu);
-	if (WARN_ON(!gicc))
-		return -EINVAL;
 
 	gsi = gicc->performance_interrupt;
 
@@ -64,11 +62,10 @@ static void arm_pmu_acpi_unregister_irq(int cpu)
 	int gsi;
 
 	gicc = acpi_cpu_get_madt_gicc(cpu);
-	if (!gicc)
-		return;
 
 	gsi = gicc->performance_interrupt;
-	acpi_unregister_gsi(gsi);
+	if (gsi)
+		acpi_unregister_gsi(gsi);
 }
 
 #if IS_ENABLED(CONFIG_ARM_SPE_PMU)

drivers/perf/fsl_imx8_ddr_perf.c

@@ -388,17 +388,19 @@ static void ddr_perf_counter_enable(struct ddr_pmu *pmu, int config,
 
 	if (enable) {
 		/*
-		 * must disable first, then enable again
-		 * otherwise, cycle counter will not work
-		 * if previous state is enabled.
+		 * cycle counter is special which should firstly write 0 then
+		 * write 1 into CLEAR bit to clear it. Other counters only
+		 * need write 0 into CLEAR bit and it turns out to be 1 by
+		 * hardware. Below enable flow is harmless for all counters.
 		 */
 		writel(0, pmu->base + reg);
 		val = CNTL_EN | CNTL_CLEAR;
 		val |= FIELD_PREP(CNTL_CSV_MASK, config);
 		writel(val, pmu->base + reg);
 	} else {
 		/* Disable counter */
-		writel(0, pmu->base + reg);
+		val = readl_relaxed(pmu->base + reg) & CNTL_EN_MASK;
+		writel(val, pmu->base + reg);
 	}
 }
 

drivers/regulator/stm32-vrefbuf.c

@@ -88,7 +88,7 @@ static int stm32_vrefbuf_disable(struct regulator_dev *rdev)
 	}
 
 	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
-	val = (val & ~STM32_ENVR) | STM32_HIZ;
+	val &= ~STM32_ENVR;
 	writel_relaxed(val, priv->base + STM32_VREFBUF_CSR);
 
 	pm_runtime_mark_last_busy(priv->dev);
@@ -175,6 +175,7 @@ static const struct regulator_desc stm32_vrefbuf_regu = {
 	.volt_table = stm32_vrefbuf_voltages,
 	.n_voltages = ARRAY_SIZE(stm32_vrefbuf_voltages),
 	.ops = &stm32_vrefbuf_volt_ops,
+	.off_on_delay = 1000,
 	.type = REGULATOR_VOLTAGE,
 	.owner = THIS_MODULE,
 };

drivers/spi/atmel-quadspi.c

@@ -149,6 +149,7 @@ struct atmel_qspi {
 	struct clk		*qspick;
 	struct platform_device	*pdev;
 	const struct atmel_qspi_caps *caps;
+	resource_size_t		mmap_size;
 	u32			pending;
 	u32			mr;
 	u32			scr;
@@ -329,6 +330,14 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
 	u32 sr, offset;
 	int err;
 
+	/*
+	 * Check if the address exceeds the MMIO window size. An improvement
+	 * would be to add support for regular SPI mode and fall back to it
+	 * when the flash memories overrun the controller's memory space.
+	 */
+	if (op->addr.val + op->data.nbytes > aq->mmap_size)
+		return -ENOTSUPP;
+
 	err = atmel_qspi_set_cfg(aq, op, &offset);
 	if (err)
 		return err;
@@ -480,6 +489,8 @@ static int atmel_qspi_probe(struct platform_device *pdev)
 		goto exit;
 	}
 
+	aq->mmap_size = resource_size(res);
+
 	/* Get the peripheral clock */
 	aq->pclk = devm_clk_get(&pdev->dev, "pclk");
 	if (IS_ERR(aq->pclk))

drivers/spi/spi-bcm63xx-hsspi.c

@@ -366,7 +366,6 @@ static int bcm63xx_hsspi_probe(struct platform_device *pdev)
 			goto out_disable_clk;
 
 		rate = clk_get_rate(pll_clk);
-		clk_disable_unprepare(pll_clk);
 		if (!rate) {
 			ret = -EINVAL;
 			goto out_disable_pll_clk;