v10.11.0

[dalathegreat]

What's Changed 📦

This release improves cybersecurity, by adding the possibility to lock the webserver behind an username/paassword. It also adds new features such as contactor control for BYD batteries, support for double-Tesla battery setups, and much more. It also starts the Diagnostic Trouble Code (DTC) refactoring project, which aims to offload DTC descriptions to the repository, instead of consuming precious flash storage space. This means the old flash limited ESP32 boards like LilyGo T-CAN485 will now benefit from the previously featuregated DTC descriptions in integrations such as BMW iX / PHEV. DTC information is read from the internet instead of from flash. Massive thanks to @malec1984 & @jonny5532 for the work!

The new option to enable username/password for the webserver

Taking this release into use ⚙️

Important

In order to OTA update to this version, you already need to be on a v10 release!

Note that v10 was a major new release of the Battery-Emulator software. The first time when taking a v10 version into use, you are required to perform an initial one time USB setup via this webpage! This is because we changed the flash frequencies, partitioning layouts and other under the hood changes to ensure longterm system stability. After any v10 has been installed via USB, following 10.X.X releases can be updated over the air.

Quickstart video: https://youtu.be/sR3t7j0R9Z0

Batteries 🔋

• Added support for Double Tesla S/3/X/Y Battery + Cellmonitor fix by @nizmot in Tesla Double Battery Support + cellmonitor fix #2378
• Tesla S/3/X/Y: Hide NOT_ACTIVE faults on Tesla HTML by @jonny5532 in Hide NOT_ACTIVE faults on Tesla HTML #2410
• Relion LV: Add contactor control via CAN by @dalathegreat in Relion LV: Add contactor control via CAN #2361
• Relion LV: Bugfix, handle battery3 contactor closing properly by @dalathegreat in Bugfix: Relion, handle battery3 contactor closing #2413
• MG5/ZS/MarvelR general stability fixes by @jonny5532 in MG5/ZS/MarvelR fixes #2417
• BYD Batteries: Added full contactor control via CAN/Webserver (previosly we could only close contactors and never open them) by @demon1300 in Feature: BYD Contactor Control #2453
• BYD Batteries: Fixed crash that occured when double battery was enabled by @demon1300 in Fix crash when BYD Atto3 dual-battery is enabled #2427
• BYD Batteries: Feature: Extend BYD auto-SOC-calibration and diagnostics to second battery by @demon1300 in Feature: Extend BYD Atto3 auto-cal and diagnostics to second battery #2431
• Ford: Improve scaling of values in more battery info page by @dalathegreat in Ford: Improve scaling of values in more battery info page #2418
• Ford: Add missing enumeration for rebalance status by @dalathegreat in Ford: Add missing enumeration for rebalance #2452
• Tesla Legacy: Add more BMS reset commands by @dalathegreat in Tesla Legacy: Add more BMS reset commands #2425
• Feature: Add DTC clearing for many battteries (Nissan/Renault/etc.) by @dalathegreat in Feature: Add DTC clearing for many battteries #2443
• BMW PHEV: Contactor control, balancing, isolation & DTCs implemented by @wjcloudy in BMW PHEV battery integration: contactor control, balancing, isolation & DTCs #2462

Inverters ⚡

• Solax: Multiple tesla batteries now possible to run with new contactor control dropdown option by @frenetic1 in Feat/solax multiple tesla bats #2211
• Kostal: Fixed an issue where battery->update_values() was called too often by @mbuhansen in fix(kostal-rs485): don't call battery->update_values() on cyclic poll #2463

Hardware 🤖

• Waveshare: Add GPIO 1/2 configurable option for status LED or I2C display by @demon1300 in Waveshare: add GPIO 1/2 configurable option for status LED or I2C display #2412
• Waveshare: Add MEB precharge pins to HAL by @dalathegreat in Waveshare: Add MEB precharge pins to HAL #2421
• BECom: Add second MCP2518 (CAN-FD2) interface option by @jonny5532 in Add second MCP2518 interface and BECom config #2068

Housekeeping 🧹

• Cybersecurity: Added password protection for web interface, by @DeadmaroZ-TLOTL in Add web interface password protection #2449
• Library 📚 Update ESP32 to v3.3.9 by @dalathegreat in Library 📚 Update ESP32 to v3.3.9 #2440
• Bugfix: CANFD restart not working by @malec1984 in Bugfix: CANFD restart not work #2423
• DTC refactoring:
  • Enhancement: DTC description files by @malec1984 in Enhancement: DTC description files #2437
  • Feature: ISO-TP library by @malec1984 in Feature: ISO-TP library #2451
  • DTC: Add initial DTC JSONs (Ford & Volvo SPA & Nissan LEAF) by @dalathegreat in DTC: Add initial DTC JSONs (Ford & Volvo SPA & Nissan LEAF) #2424
  • Enhancement: DTC descriptions based on JSON file by @malec1984 in Enhancement: DTC descriptions based on JSON file #2430
• Improvement: Reduce number of duplicate builds by @dalathegreat in Improvement/node js20deprecated #2459
• Feature: Add component detection events to make system easier to troubleshoot by @dalathegreat in Feature: Add component detection events to make system easier to troubleshoot #2455

New Contributors

• @DeadmaroZ-TLOTL made their first contribution in Add web interface password protection #2449

Full Changelog: v10.10.1...v10.11.0

---

This discussion was created from the release v10.11.0.