Initial TS-7990 support by ts-kris · Pull Request #7 · embeddedTS/linux-lts

ts-kris · 2023-01-06T23:10:42Z

Add support for TS-7990 and variants.

Also includes some driver patches.

The pixcir driver (LCD cap touch) needed modification to put it in active high IRQ mode. Patch was based on similar modification in linux-tsimx repo.
The ads7846 driver (Okaya/Microtip resistive touch) did not have an SPI ID struct and therefore fails to auto-load as a module. This will get pushed upstream shortly hopefully but likely won't get backported here so that commit will need to hang around.

As the TS-7990 uses the WILC3000 Wi-Fi module, the defconfig was modified to not enable 802.11 power savings by default as this has been observed to cause issues with the driver.

NOTE
This should be merged after #5, in either case there will likely be some conflicts with dts/Makefile that need to be sorted out.

The only variants tested were Quad LXD Rev B, and Quad Okaya Rev B. At this time I do not have any Solo CPUs nor Rev A PCBs.

ts-kris · 2023-01-20T22:56:56Z

As of #9, this PR needs some rework to remove conflicts

The TS-TPC-7990 has an inverted interrupt system in order to allow the touchscreen to wake the device. The CPU pin is expecting a falling IRQ, but the INT pin on the touchscreen controller must be set to active high output. This adds invert-int-output property to the devicetree parsing. If set, it inverts the INT output from the controller, but the driver remains configured for active low IRQ. Base on commit 461fc502098ea5296e0cb3de6afd567a4ce17874 from https://github.com/embeddedTS/linux-tsimx Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>

If compiled as a module, "ti,ads7846" is the only compatible string that would cause the module to loaded automatically. Add spi_device_id table to correctly load the module for all supported devices. Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>

ts-kris · 2023-01-21T00:00:58Z

Dropped commits to tsimx6_defconfig and verified that ts_defconfig had those options.

Similar support to what is available in our linux-tsimx repo. Supports all TS-7990 variants including LXD, Okaya, and Microtips LCDs and touch screens. Signed-off-by: Kris Bahnsen <kris@embeddedTS.com> Signed-off-by: Mark Featherston <mark@embeddedTS.com>

ts-kris · 2023-01-24T22:09:13Z

Latest force push was to touch compatibility strings to change from ts4900 to ts7990 across all files.

[ Upstream commit af68656 ] While handling PCI errors (AER flow) driver tries to disable NAPI [napi_disable()] after NAPI is deleted [__netif_napi_del()] which causes unexpected system hang/crash. System message log shows the following: ======================================= [ 3222.537510] EEH: Detected PCI bus error on PHB#384-PE#800000 [ 3222.537511] EEH: This PCI device has failed 2 times in the last hour and will be permanently disabled after 5 failures. [ 3222.537512] EEH: Notify device drivers to shutdown [ 3222.537513] EEH: Beginning: 'error_detected(IO frozen)' [ 3222.537514] EEH: PE#800000 (PCI 0384:80:00.0): Invoking bnx2x->error_detected(IO frozen) [ 3222.537516] bnx2x: [bnx2x_io_error_detected:14236(eth14)]IO error detected [ 3222.537650] EEH: PE#800000 (PCI 0384:80:00.0): bnx2x driver reports: 'need reset' [ 3222.537651] EEH: PE#800000 (PCI 0384:80:00.1): Invoking bnx2x->error_detected(IO frozen) [ 3222.537651] bnx2x: [bnx2x_io_error_detected:14236(eth13)]IO error detected [ 3222.537729] EEH: PE#800000 (PCI 0384:80:00.1): bnx2x driver reports: 'need reset' [ 3222.537729] EEH: Finished:'error_detected(IO frozen)' with aggregate recovery state:'need reset' [ 3222.537890] EEH: Collect temporary log [ 3222.583481] EEH: of node=0384:80:00.0 [ 3222.583519] EEH: PCI device/vendor: 168e14e4 [ 3222.583557] EEH: PCI cmd/status register: 00100140 [ 3222.583557] EEH: PCI-E capabilities and status follow: [ 3222.583744] EEH: PCI-E 00: 00020010 012c8da 00095d5e 00455c82 [ 3222.583892] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.583893] EEH: PCI-E 20: 00000000 [ 3222.583893] EEH: PCI-E AER capability register set follows: [ 3222.584079] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.584230] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.584378] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.584416] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.584416] EEH: of node=0384:80:00.1 [ 3222.584454] EEH: PCI device/vendor: 168e14e4 [ 3222.584491] EEH: PCI cmd/status register: 00100140 [ 3222.584492] EEH: PCI-E capabilities and status follow: [ 3222.584677] EEH: PCI-E 00: 00020010 012c8da 00095d5e 00455c82 [ 3222.584825] EEH: PCI-E 10: 10820000 00000000 00000000 00000000 [ 3222.584826] EEH: PCI-E 20: 00000000 [ 3222.584826] EEH: PCI-E AER capability register set follows: [ 3222.585011] EEH: PCI-E AER 00: 13c10001 00000000 00000000 00062030 [ 3222.585160] EEH: PCI-E AER 10: 00002000 000031c0 000001e0 00000000 [ 3222.585309] EEH: PCI-E AER 20: 00000000 00000000 00000000 00000000 [ 3222.585347] EEH: PCI-E AER 30: 00000000 00000000 [ 3222.586872] RTAS: event: 5, Type: Platform Error (224), Severity: 2 [ 3222.586873] EEH: Reset without hotplug activity [ 3224.762767] EEH: Beginning: 'slot_reset' [ 3224.762770] EEH: PE#800000 (PCI 0384:80:00.0): Invoking bnx2x->slot_reset() [ 3224.762771] bnx2x: [bnx2x_io_slot_reset:14271(eth14)]IO slot reset initializing... [ 3224.762887] bnx2x 0384:80:00.0: enabling device (0140 -> 0142) [ 3224.768157] bnx2x: [bnx2x_io_slot_reset:14287(eth14)]IO slot reset --> driver unload Uninterruptible tasks ===================== crash> ps | grep UN 213 2 11 c000000004c89e00 UN 0.0 0 0 [eehd] 215 2 0 c000000004c80000 UN 0.0 0 0 [kworker/0:2] 2196 1 28 c000000004504f00 UN 0.1 15936 11136 wickedd 4287 1 9 c00000020d076800 UN 0.0 4032 3008 agetty 4289 1 20 c00000020d056680 UN 0.0 7232 3840 agetty 32423 2 26 c00000020038c580 UN 0.0 0 0 [kworker/26:3] 32871 4241 27 c0000002609ddd00 UN 0.1 18624 11648 sshd 32920 10130 16 c00000027284a100 UN 0.1 48512 12608 sendmail 33092 32987 0 c000000205218b00 UN 0.1 48512 12608 sendmail 33154 4567 16 c000000260e51780 UN 0.1 48832 12864 pickup 33209 4241 36 c000000270cb6500 UN 0.1 18624 11712 sshd 33473 33283 0 c000000205211480 UN 0.1 48512 12672 sendmail 33531 4241 37 c00000023c902780 UN 0.1 18624 11648 sshd EEH handler hung while bnx2x sleeping and holding RTNL lock =========================================================== crash> bt 213 PID: 213 TASK: c000000004c89e00 CPU: 11 COMMAND: "eehd" #0 [c000000004d477e0] __schedule at c000000000c70808 #1 [c000000004d478b0] schedule at c000000000c70ee0 #2 [c000000004d478e0] schedule_timeout at c000000000c76dec #3 [c000000004d479c0] msleep at c0000000002120cc #4 [c000000004d479f0] napi_disable at c000000000a06448 ^^^^^^^^^^^^^^^^ #5 [c000000004d47a30] bnx2x_netif_stop at c0080000018dba94 [bnx2x] #6 [c000000004d47a60] bnx2x_io_slot_reset at c0080000018a551c [bnx2x] #7 [c000000004d47b20] eeh_report_reset at c00000000004c9bc #8 [c000000004d47b90] eeh_pe_report at c00000000004d1a8 #9 [c000000004d47c40] eeh_handle_normal_event at c00000000004da64 And the sleeping source code ============================ crash> dis -ls c000000000a06448 FILE: ../net/core/dev.c LINE: 6702 6697 { 6698 might_sleep(); 6699 set_bit(NAPI_STATE_DISABLE, &n->state); 6700 6701 while (test_and_set_bit(NAPI_STATE_SCHED, &n->state)) * 6702 msleep(1); 6703 while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state)) 6704 msleep(1); 6705 6706 hrtimer_cancel(&n->timer); 6707 6708 clear_bit(NAPI_STATE_DISABLE, &n->state); 6709 } EEH calls into bnx2x twice based on the system log above, first through bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes the following call chains: bnx2x_io_error_detected() +-> bnx2x_eeh_nic_unload() +-> bnx2x_del_all_napi() +-> __netif_napi_del() bnx2x_io_slot_reset() +-> bnx2x_netif_stop() +-> bnx2x_napi_disable() +->napi_disable() Fix this by correcting the sequence of NAPI APIs usage, that is delete the NAPI after disabling it. Fixes: 7fa6f34 ("bnx2x: AER revised") Reported-by: David Christensen <drc@linux.vnet.ibm.com> Tested-by: David Christensen <drc@linux.vnet.ibm.com> Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Link: https://lore.kernel.org/r/20220426153913.6966-1-manishc@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 38c9c22 upstream. Syzkaller reported use-after-free bug as follows: ================================================================== BUG: KASAN: use-after-free in ntfs_ucsncmp+0x123/0x130 Read of size 2 at addr ffff8880751acee8 by task a.out/879 CPU: 7 PID: 879 Comm: a.out Not tainted 5.19.0-rc4-next-20220630-00001-gcc5218c8bd2c-dirty #7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 Call Trace: <TASK> dump_stack_lvl+0x1c0/0x2b0 print_address_description.constprop.0.cold+0xd4/0x484 print_report.cold+0x55/0x232 kasan_report+0xbf/0xf0 ntfs_ucsncmp+0x123/0x130 ntfs_are_names_equal.cold+0x2b/0x41 ntfs_attr_find+0x43b/0xb90 ntfs_attr_lookup+0x16d/0x1e0 ntfs_read_locked_attr_inode+0x4aa/0x2360 ntfs_attr_iget+0x1af/0x220 ntfs_read_locked_inode+0x246c/0x5120 ntfs_iget+0x132/0x180 load_system_files+0x1cc6/0x3480 ntfs_fill_super+0xa66/0x1cf0 mount_bdev+0x38d/0x460 legacy_get_tree+0x10d/0x220 vfs_get_tree+0x93/0x300 do_new_mount+0x2da/0x6d0 path_mount+0x496/0x19d0 __x64_sys_mount+0x284/0x300 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x46/0xb0 RIP: 0033:0x7f3f2118d9ea Code: 48 8b 0d a9 f4 0b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 49 89 ca b8 a5 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 76 f4 0b 00 f7 d8 64 89 01 48 RSP: 002b:00007ffc269deac8 EFLAGS: 00000202 ORIG_RAX: 00000000000000a5 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f3f2118d9ea RDX: 0000000020000000 RSI: 0000000020000100 RDI: 00007ffc269dec00 RBP: 00007ffc269dec80 R08: 00007ffc269deb00 R09: 00007ffc269dec44 R10: 0000000000000000 R11: 0000000000000202 R12: 000055f81ab1d220 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 </TASK> The buggy address belongs to the physical page: page:0000000085430378 refcount:1 mapcount:1 mapping:0000000000000000 index:0x555c6a81d pfn:0x751ac memcg:ffff888101f7e180 anon flags: 0xfffffc00a0014(uptodate|lru|mappedtodisk|swapbacked|node=0|zone=1|lastcpupid=0x1fffff) raw: 000fffffc00a0014 ffffea0001bf2988 ffffea0001de2448 ffff88801712e201 raw: 0000000555c6a81d 0000000000000000 0000000100000000 ffff888101f7e180 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8880751acd80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8880751ace00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff8880751ace80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ^ ffff8880751acf00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8880751acf80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ================================================================== The reason is that struct ATTR_RECORD->name_offset is 6485, end address of name string is out of bounds. Fix this by adding sanity check on end address of attribute name string. [akpm@linux-foundation.org: coding-style cleanups] [chenxiaosong2@huawei.com: cleanup suggested by Hawkins Jiawei] Link: https://lkml.kernel.org/r/20220709064511.3304299-1-chenxiaosong2@huawei.com Link: https://lkml.kernel.org/r/20220707105329.4020708-1-chenxiaosong2@huawei.com Signed-off-by: ChenXiaoSong <chenxiaosong2@huawei.com> Signed-off-by: Hawkins Jiawei <yin31149@gmail.com> Cc: Anton Altaparmakov <anton@tuxera.com> Cc: ChenXiaoSong <chenxiaosong2@huawei.com> Cc: Yongqiang Liu <liuyongqiang13@huawei.com> Cc: Zhang Yi <yi.zhang@huawei.com> Cc: Zhang Xiaoxu <zhangxiaoxu5@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…loc() commit d29f590 upstream. The voice allocator sometimes begins allocating from near the end of the array and then wraps around, however snd_emu10k1_pcm_channel_alloc() accesses the newly allocated voices as if it never wrapped around. This results in out of bounds access if the first voice has a high enough index so that first_voice + requested_voice_count > NUM_G (64). The more voices are requested, the more likely it is for this to occur. This was initially discovered using PipeWire, however it can be reproduced by calling aplay multiple times with 16 channels: aplay -r 48000 -D plughw:CARD=Live,DEV=3 -c 16 /dev/zero UBSAN: array-index-out-of-bounds in sound/pci/emu10k1/emupcm.c:127:40 index 65 is out of range for type 'snd_emu10k1_voice [64]' CPU: 1 PID: 31977 Comm: aplay Tainted: G W IOE 6.0.0-rc2-emu10k1+ #7 Hardware name: ASUSTEK COMPUTER INC P5W DH Deluxe/P5W DH Deluxe, BIOS 3002 07/22/2010 Call Trace: <TASK> dump_stack_lvl+0x49/0x63 dump_stack+0x10/0x16 ubsan_epilogue+0x9/0x3f __ubsan_handle_out_of_bounds.cold+0x44/0x49 snd_emu10k1_playback_hw_params+0x3bc/0x420 [snd_emu10k1] snd_pcm_hw_params+0x29f/0x600 [snd_pcm] snd_pcm_common_ioctl+0x188/0x1410 [snd_pcm] ? exit_to_user_mode_prepare+0x35/0x170 ? do_syscall_64+0x69/0x90 ? syscall_exit_to_user_mode+0x26/0x50 ? do_syscall_64+0x69/0x90 ? exit_to_user_mode_prepare+0x35/0x170 snd_pcm_ioctl+0x27/0x40 [snd_pcm] __x64_sys_ioctl+0x95/0xd0 do_syscall_64+0x5c/0x90 ? do_syscall_64+0x69/0x90 ? do_syscall_64+0x69/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Signed-off-by: Tasos Sahanidis <tasos@tasossah.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/3707dcab-320a-62ff-63c0-73fc201ef756@tasossah.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

…g the sock [ Upstream commit 3cf7203 ] There is a race condition in vxlan that when deleting a vxlan device during receiving packets, there is a possibility that the sock is released after getting vxlan_sock vs from sk_user_data. Then in later vxlan_ecn_decapsulate(), vxlan_get_sk_family() we will got NULL pointer dereference. e.g. #0 [ffffa25ec6978a38] machine_kexec at ffffffff8c669757 #1 [ffffa25ec6978a90] __crash_kexec at ffffffff8c7c0a4d #2 [ffffa25ec6978b58] crash_kexec at ffffffff8c7c1c48 #3 [ffffa25ec6978b60] oops_end at ffffffff8c627f2b #4 [ffffa25ec6978b80] page_fault_oops at ffffffff8c678fcb #5 [ffffa25ec6978bd8] exc_page_fault at ffffffff8d109542 #6 [ffffa25ec6978c00] asm_exc_page_fault at ffffffff8d200b62 [exception RIP: vxlan_ecn_decapsulate+0x3b] RIP: ffffffffc1014e7b RSP: ffffa25ec6978cb0 RFLAGS: 00010246 RAX: 0000000000000008 RBX: ffff8aa000888000 RCX: 0000000000000000 RDX: 000000000000000e RSI: ffff8a9fc7ab803e RDI: ffff8a9fd1168700 RBP: ffff8a9fc7ab803e R8: 0000000000700000 R9: 00000000000010ae R10: ffff8a9fcb748980 R11: 0000000000000000 R12: ffff8a9fd1168700 R13: ffff8aa000888000 R14: 00000000002a0000 R15: 00000000000010ae ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #7 [ffffa25ec6978ce8] vxlan_rcv at ffffffffc10189cd [vxlan] #8 [ffffa25ec6978d90] udp_queue_rcv_one_skb at ffffffff8cfb6507 #9 [ffffa25ec6978dc0] udp_unicast_rcv_skb at ffffffff8cfb6e45 #10 [ffffa25ec6978dc8] __udp4_lib_rcv at ffffffff8cfb8807 #11 [ffffa25ec6978e20] ip_protocol_deliver_rcu at ffffffff8cf76951 #12 [ffffa25ec6978e48] ip_local_deliver at ffffffff8cf76bde #13 [ffffa25ec6978ea0] __netif_receive_skb_one_core at ffffffff8cecde9b #14 [ffffa25ec6978ec8] process_backlog at ffffffff8cece139 #15 [ffffa25ec6978f00] __napi_poll at ffffffff8ceced1a #16 [ffffa25ec6978f28] net_rx_action at ffffffff8cecf1f3 #17 [ffffa25ec6978fa0] __softirqentry_text_start at ffffffff8d4000ca #18 [ffffa25ec6978ff0] do_softirq at ffffffff8c6fbdc3 Reproducer: https://github.com/Mellanox/ovs-tests/blob/master/test-ovs-vxlan-remove-tunnel-during-traffic.sh Fix this by waiting for all sk_user_data reader to finish before releasing the sock. Reported-by: Jianlin Shi <jishi@redhat.com> Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Fixes: 6a93cc9 ("udp-tunnel: Add a few more UDP tunnel APIs") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b18cba0 ] Commit 9130b8d ("SUNRPC: allow for upcalls for the same uid but different gss service") introduced `auth` argument to __gss_find_upcall(), but in gss_pipe_downcall() it was left as NULL since it (and auth->service) was not (yet) determined. When multiple upcalls with the same uid and different service are ongoing, it could happen that __gss_find_upcall(), which returns the first match found in the pipe->in_downcall list, could not find the correct gss_msg corresponding to the downcall we are looking for. Moreover, it might return a msg which is not sent to rpc.gssd yet. We could see mount.nfs process hung in D state with multiple mount.nfs are executed in parallel. The call trace below is of CentOS 7.9 kernel-3.10.0-1160.24.1.el7.x86_64 but we observed the same hang w/ elrepo kernel-ml-6.0.7-1.el7. PID: 71258 TASK: ffff91ebd4be0000 CPU: 36 COMMAND: "mount.nfs" #0 [ffff9203ca3234f8] __schedule at ffffffffa3b8899f #1 [ffff9203ca323580] schedule at ffffffffa3b88eb9 #2 [ffff9203ca323590] gss_cred_init at ffffffffc0355818 [auth_rpcgss] #3 [ffff9203ca323658] rpcauth_lookup_credcache at ffffffffc0421ebc [sunrpc] #4 [ffff9203ca3236d8] gss_lookup_cred at ffffffffc0353633 [auth_rpcgss] #5 [ffff9203ca3236e8] rpcauth_lookupcred at ffffffffc0421581 [sunrpc] #6 [ffff9203ca323740] rpcauth_refreshcred at ffffffffc04223d3 [sunrpc] #7 [ffff9203ca3237a0] call_refresh at ffffffffc04103dc [sunrpc] #8 [ffff9203ca3237b8] __rpc_execute at ffffffffc041e1c9 [sunrpc] #9 [ffff9203ca323820] rpc_execute at ffffffffc0420a48 [sunrpc] The scenario is like this. Let's say there are two upcalls for services A and B, A -> B in pipe->in_downcall, B -> A in pipe->pipe. When rpc.gssd reads pipe to get the upcall msg corresponding to service B from pipe->pipe and then writes the response, in gss_pipe_downcall the msg corresponding to service A will be picked because only uid is used to find the msg and it is before the one for B in pipe->in_downcall. And the process waiting for the msg corresponding to service A will be woken up. Actual scheduing of that process might be after rpc.gssd processes the next msg. In rpc_pipe_generic_upcall it clears msg->errno (for A). The process is scheduled to see gss_msg->ctx == NULL and gss_msg->msg.errno == 0, therefore it cannot break the loop in gss_create_upcall and is never woken up after that. This patch adds a simple check to ensure that a msg which is not sent to rpc.gssd yet is not chosen as the matching upcall upon receiving a downcall. Signed-off-by: minoura makoto <minoura@valinux.co.jp> Signed-off-by: Hiroshi Shimamoto <h-shimamoto@nec.com> Tested-by: Hiroshi Shimamoto <h-shimamoto@nec.com> Cc: Trond Myklebust <trondmy@hammerspace.com> Fixes: 9130b8d ("SUNRPC: allow for upcalls for same uid but different gss service") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6c4ca03 ] During EEH error injection testing, a deadlock was encountered in the tg3 driver when tg3_io_error_detected() was attempting to cancel outstanding reset tasks: crash> foreach UN bt ... PID: 159 TASK: c0000000067c6000 CPU: 8 COMMAND: "eehd" ... #5 [c00000000681f990] __cancel_work_timer at c00000000019fd18 #6 [c00000000681fa30] tg3_io_error_detected at c00800000295f098 [tg3] #7 [c00000000681faf0] eeh_report_error at c00000000004e25c ... PID: 290 TASK: c000000036e5f800 CPU: 6 COMMAND: "kworker/6:1" ... #4 [c00000003721fbc0] rtnl_lock at c000000000c940d8 #5 [c00000003721fbe0] tg3_reset_task at c008000002969358 [tg3] #6 [c00000003721fc60] process_one_work at c00000000019e5c4 ... PID: 296 TASK: c000000037a65800 CPU: 21 COMMAND: "kworker/21:1" ... #4 [c000000037247bc0] rtnl_lock at c000000000c940d8 #5 [c000000037247be0] tg3_reset_task at c008000002969358 [tg3] #6 [c000000037247c60] process_one_work at c00000000019e5c4 ... PID: 655 TASK: c000000036f49000 CPU: 16 COMMAND: "kworker/16:2" ...:1 #4 [c0000000373ebbc0] rtnl_lock at c000000000c940d8 #5 [c0000000373ebbe0] tg3_reset_task at c008000002969358 [tg3] #6 [c0000000373ebc60] process_one_work at c00000000019e5c4 ... Code inspection shows that both tg3_io_error_detected() and tg3_reset_task() attempt to acquire the RTNL lock at the beginning of their code blocks. If tg3_reset_task() should happen to execute between the times when tg3_io_error_deteced() acquires the RTNL lock and tg3_reset_task_cancel() is called, a deadlock will occur. Moving tg3_reset_task_cancel() call earlier within the code block, prior to acquiring RTNL, prevents this from happening, but also exposes another deadlock issue where tg3_reset_task() may execute AFTER tg3_io_error_detected() has executed: crash> foreach UN bt PID: 159 TASK: c0000000067d2000 CPU: 9 COMMAND: "eehd" ... #4 [c000000006867a60] rtnl_lock at c000000000c940d8 #5 [c000000006867a80] tg3_io_slot_reset at c0080000026c2ea8 [tg3] #6 [c000000006867b00] eeh_report_reset at c00000000004de88 ... PID: 363 TASK: c000000037564000 CPU: 6 COMMAND: "kworker/6:1" ... #3 [c000000036c1bb70] msleep at c000000000259e6c #4 [c000000036c1bba0] napi_disable at c000000000c6b848 #5 [c000000036c1bbe0] tg3_reset_task at c0080000026d942c [tg3] #6 [c000000036c1bc60] process_one_work at c00000000019e5c4 ... This issue can be avoided by aborting tg3_reset_task() if EEH error recovery is already in progress. Fixes: db84bf4 ("tg3: tg3_reset_task() needs to use rtnl_lock to synchronize") Signed-off-by: David Christensen <drc@linux.vnet.ibm.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230124185339.225806-1-drc@linux.vnet.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 1a5352a upstream. The ath11k active pdevs are protected by RCU but the temperature event handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a read-side critical section as reported by RCU lockdep: ============================= WARNING: suspicious RCU usage 6.6.0-rc6 #7 Not tainted ----------------------------- drivers/net/wireless/ath/ath11k/mac.c:638 suspicious rcu_dereference_check() usage! other info that might help us debug this: rcu_scheduler_active = 2, debug_locks = 1 no locks held by swapper/0/0. ... Call trace: ... lockdep_rcu_suspicious+0x16c/0x22c ath11k_mac_get_ar_by_pdev_id+0x194/0x1b0 [ath11k] ath11k_wmi_tlv_op_rx+0xa84/0x2c1c [ath11k] ath11k_htc_rx_completion_handler+0x388/0x510 [ath11k] Mark the code in question as an RCU read-side critical section to avoid any potential use-after-free issues. Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23 Fixes: a41d103 ("ath11k: add thermal sensor device support") Cc: stable@vger.kernel.org # 5.7 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20231019153115.26401-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b684c09 upstream. ppc_save_regs() skips one stack frame while saving the CPU register states. Instead of saving current R1, it pulls the previous stack frame pointer. When vmcores caused by direct panic call (such as `echo c > /proc/sysrq-trigger`), are debugged with gdb, gdb fails to show the backtrace correctly. On further analysis, it was found that it was because of mismatch between r1 and NIP. GDB uses NIP to get current function symbol and uses corresponding debug info of that function to unwind previous frames, but due to the mismatching r1 and NIP, the unwinding does not work, and it fails to unwind to the 2nd frame and hence does not show the backtrace. GDB backtrace with vmcore of kernel without this patch: --------- (gdb) bt #0 0xc0000000002a53e8 in crash_setup_regs (oldregs=<optimized out>, newregs=0xc000000004f8f8d8) at ./arch/powerpc/include/asm/kexec.h:69 #1 __crash_kexec (regs=<optimized out>) at kernel/kexec_core.c:974 #2 0x0000000000000063 in ?? () #3 0xc000000003579320 in ?? () --------- Further analysis revealed that the mismatch occurred because "ppc_save_regs" was saving the previous stack's SP instead of the current r1. This patch fixes this by storing current r1 in the saved pt_regs. GDB backtrace with vmcore of patched kernel: -------- (gdb) bt #0 0xc0000000002a53e8 in crash_setup_regs (oldregs=0x0, newregs=0xc00000000670b8d8) at ./arch/powerpc/include/asm/kexec.h:69 #1 __crash_kexec (regs=regs@entry=0x0) at kernel/kexec_core.c:974 #2 0xc000000000168918 in panic (fmt=fmt@entry=0xc000000001654a60 "sysrq triggered crash\n") at kernel/panic.c:358 #3 0xc000000000b735f8 in sysrq_handle_crash (key=<optimized out>) at drivers/tty/sysrq.c:155 #4 0xc000000000b742cc in __handle_sysrq (key=key@entry=99, check_mask=check_mask@entry=false) at drivers/tty/sysrq.c:602 #5 0xc000000000b7506c in write_sysrq_trigger (file=<optimized out>, buf=<optimized out>, count=2, ppos=<optimized out>) at drivers/tty/sysrq.c:1163 #6 0xc00000000069a7bc in pde_write (ppos=<optimized out>, count=<optimized out>, buf=<optimized out>, file=<optimized out>, pde=0xc00000000362cb40) at fs/proc/inode.c:340 #7 proc_reg_write (file=<optimized out>, buf=<optimized out>, count=<optimized out>, ppos=<optimized out>) at fs/proc/inode.c:352 #8 0xc0000000005b3bbc in vfs_write (file=file@entry=0xc000000006aa6b00, buf=buf@entry=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=count@entry=2, pos=pos@entry=0xc00000000670bda0) at fs/read_write.c:582 #9 0xc0000000005b4264 in ksys_write (fd=<optimized out>, buf=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=2) at fs/read_write.c:637 #10 0xc00000000002ea2c in system_call_exception (regs=0xc00000000670be80, r0=<optimized out>) at arch/powerpc/kernel/syscall.c:171 #11 0xc00000000000c270 in system_call_vectored_common () at arch/powerpc/kernel/interrupt_64.S:192 -------- Nick adds: So this now saves regs as though it was an interrupt taken in the caller, at the instruction after the call to ppc_save_regs, whereas previously the NIP was there, but R1 came from the caller's caller and that mismatch is what causes gdb's dwarf unwinder to go haywire. Signed-off-by: Aditya Gupta <adityag@linux.ibm.com> Fixes: d16a58f ("powerpc: Improve ppc_save_regs()") Reivewed-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230615091047.90433-1-adityag@linux.ibm.com Cc: stable@vger.kernel.org Signed-off-by: Aditya Gupta <adityag@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 1947b92 ] Parallel testing appears to show a race between allocating and setting evsel ids. As there is a bounds check on the xyarray it yields a segv like: ``` AddressSanitizer:DEADLYSIGNAL ================================================================= ==484408==ERROR: AddressSanitizer: SEGV on unknown address 0x000000000010 ==484408==The signal is caused by a WRITE memory access. ==484408==Hint: address points to the zero page. #0 0x55cef5d4eff4 in perf_evlist__id_hash tools/lib/perf/evlist.c:256 #1 0x55cef5d4f132 in perf_evlist__id_add tools/lib/perf/evlist.c:274 #2 0x55cef5d4f545 in perf_evlist__id_add_fd tools/lib/perf/evlist.c:315 #3 0x55cef5a1923f in store_evsel_ids util/evsel.c:3130 #4 0x55cef5a19400 in evsel__store_ids util/evsel.c:3147 #5 0x55cef5888204 in __run_perf_stat tools/perf/builtin-stat.c:832 #6 0x55cef5888c06 in run_perf_stat tools/perf/builtin-stat.c:960 #7 0x55cef58932db in cmd_stat tools/perf/builtin-stat.c:2878 ... ``` Avoid this crash by early exiting the perf_evlist__id_add_fd and perf_evlist__id_add is the access is out-of-bounds. Signed-off-by: Ian Rogers <irogers@google.com> Cc: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240229070757.796244-1-irogers@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>

commit ac01c8c upstream. AddressSanitizer found a use-after-free bug in the symbol code which manifested as 'perf top' segfaulting. ==1238389==ERROR: AddressSanitizer: heap-use-after-free on address 0x60b00c48844b at pc 0x5650d8035961 bp 0x7f751aaecc90 sp 0x7f751aaecc80 READ of size 1 at 0x60b00c48844b thread T193 #0 0x5650d8035960 in _sort__sym_cmp util/sort.c:310 #1 0x5650d8043744 in hist_entry__cmp util/hist.c:1286 #2 0x5650d8043951 in hists__findnew_entry util/hist.c:614 #3 0x5650d804568f in __hists__add_entry util/hist.c:754 #4 0x5650d8045bf9 in hists__add_entry util/hist.c:772 #5 0x5650d8045df1 in iter_add_single_normal_entry util/hist.c:997 #6 0x5650d8043326 in hist_entry_iter__add util/hist.c:1242 #7 0x5650d7ceeefe in perf_event__process_sample /home/matt/src/linux/tools/perf/builtin-top.c:845 #8 0x5650d7ceeefe in deliver_event /home/matt/src/linux/tools/perf/builtin-top.c:1208 #9 0x5650d7fdb51b in do_flush util/ordered-events.c:245 #10 0x5650d7fdb51b in __ordered_events__flush util/ordered-events.c:324 #11 0x5650d7ced743 in process_thread /home/matt/src/linux/tools/perf/builtin-top.c:1120 #12 0x7f757ef1f133 in start_thread nptl/pthread_create.c:442 #13 0x7f757ef9f7db in clone3 ../sysdeps/unix/sysv/linux/x86_64/clone3.S:81 When updating hist maps it's also necessary to update the hist symbol reference because the old one gets freed in map__put(). While this bug was probably introduced with 5c24b67 ("perf tools: Replace map->referenced & maps->removed_maps with map->refcnt"), the symbol objects were leaked until c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") was merged so the bug was masked. Fixes: c087e94 ("perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL") Reported-by: Yunzhao Li <yunzhao@cloudflare.com> Signed-off-by: Matt Fleming (Cloudflare) <matt@readmodwrite.com> Cc: Ian Rogers <irogers@google.com> Cc: kernel-team@cloudflare.com Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: stable@vger.kernel.org # v5.13+ Link: https://lore.kernel.org/r/20240815142212.3834625-1-matt@readmodwrite.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9af2efe upstream. The fields in the hist_entry are filled on-demand which means they only have meaningful values when relevant sort keys are used. So if neither of 'dso' nor 'sym' sort keys are used, the map/symbols in the hist entry can be garbage. So it shouldn't access it unconditionally. I got a segfault, when I wanted to see cgroup profiles. $ sudo perf record -a --all-cgroups --synth=cgroup true $ sudo perf report -s cgroup Program received signal SIGSEGV, Segmentation fault. 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 48 return RC_CHK_ACCESS(map)->dso; (gdb) bt #0 0x00005555557a8d90 in map__dso (map=0x0) at util/map.h:48 #1 0x00005555557aa39b in map__load (map=0x0) at util/map.c:344 #2 0x00005555557aa592 in map__find_symbol (map=0x0, addr=140736115941088) at util/map.c:385 #3 0x00005555557ef000 in hists__findnew_entry (hists=0x555556039d60, entry=0x7fffffffa4c0, al=0x7fffffffa8c0, sample_self=true) at util/hist.c:644 #4 0x00005555557ef61c in __hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, block_info=0x0, sample=0x7fffffffaa90, sample_self=true, ops=0x0) at util/hist.c:761 #5 0x00005555557ef71f in hists__add_entry (hists=0x555556039d60, al=0x7fffffffa8c0, sym_parent=0x0, bi=0x0, mi=0x0, ki=0x0, sample=0x7fffffffaa90, sample_self=true) at util/hist.c:779 #6 0x00005555557f00fb in iter_add_single_normal_entry (iter=0x7fffffffa900, al=0x7fffffffa8c0) at util/hist.c:1015 #7 0x00005555557f09a7 in hist_entry_iter__add (iter=0x7fffffffa900, al=0x7fffffffa8c0, max_stack_depth=127, arg=0x7fffffffbce0) at util/hist.c:1260 #8 0x00005555555ba7ce in process_sample_event (tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at builtin-report.c:334 #9 0x00005555557b30c8 in evlist__deliver_sample (evlist=0x555556039010, tool=0x7fffffffbce0, event=0x7ffff7c14128, sample=0x7fffffffaa90, evsel=0x555556039ad0, machine=0x5555560388e8) at util/session.c:1232 #10 0x00005555557b32bc in machines__deliver_event (machines=0x5555560388e8, evlist=0x555556039010, event=0x7ffff7c14128, sample=0x7fffffffaa90, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1271 #11 0x00005555557b3848 in perf_session__deliver_event (session=0x5555560386d0, event=0x7ffff7c14128, tool=0x7fffffffbce0, file_offset=110888, file_path=0x555556038ff0 "perf.data") at util/session.c:1354 #12 0x00005555557affaf in ordered_events__deliver_event (oe=0x555556038e60, event=0x555556135aa0) at util/session.c:132 #13 0x00005555557bb605 in do_flush (oe=0x555556038e60, show_progress=false) at util/ordered-events.c:245 #14 0x00005555557bb95c in __ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND, timestamp=0) at util/ordered-events.c:324 #15 0x00005555557bba46 in ordered_events__flush (oe=0x555556038e60, how=OE_FLUSH__ROUND) at util/ordered-events.c:342 #16 0x00005555557b1b3b in perf_event__process_finished_round (tool=0x7fffffffbce0, event=0x7ffff7c15bb8, oe=0x555556038e60) at util/session.c:780 #17 0x00005555557b3b27 in perf_session__process_user_event (session=0x5555560386d0, event=0x7ffff7c15bb8, file_offset=117688, file_path=0x555556038ff0 "perf.data") at util/session.c:1406 As you can see the entry->ms.map was NULL even if he->ms.map has a value. This is because 'sym' sort key is not given, so it cannot assume whether he->ms.sym and entry->ms.sym is the same. I only checked the 'sym' sort key here as it implies 'dso' behavior (so maps are the same). Fixes: ac01c8c ("perf hist: Update hist symbol when updating maps") Signed-off-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Matt Fleming <matt@readmodwrite.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Link: https://lore.kernel.org/r/20240826221045.1202305-2-namhyung@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a848c29 ] On the node of an NFS client, some files saved in the mountpoint of the NFS server were copied to another location of the same NFS server. Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference crash with the following syslog: [232064.838881] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232064.839360] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232066.588183] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058 [232066.588586] Mem abort info: [232066.588701] ESR = 0x0000000096000007 [232066.588862] EC = 0x25: DABT (current EL), IL = 32 bits [232066.589084] SET = 0, FnV = 0 [232066.589216] EA = 0, S1PTW = 0 [232066.589340] FSC = 0x07: level 3 translation fault [232066.589559] Data abort info: [232066.589683] ISV = 0, ISS = 0x00000007 [232066.589842] CM = 0, WnR = 0 [232066.589967] user pgtable: 64k pages, 48-bit VAs, pgdp=00002000956ff400 [232066.590231] [0000000000000058] pgd=08001100ae100003, p4d=08001100ae100003, pud=08001100ae100003, pmd=08001100b3c00003, pte=0000000000000000 [232066.590757] Internal error: Oops: 96000007 [#1] SMP [232066.590958] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm vhost_net vhost vhost_iotlb tap tun ipt_rpfilter xt_multiport ip_set_hash_ip ip_set_hash_net xfrm_interface xfrm6_tunnel tunnel4 tunnel6 esp4 ah4 wireguard libcurve25519_generic veth xt_addrtype xt_set nf_conntrack_netlink ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_bitmap_port ip_set_hash_ipport dummy ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs iptable_filter sch_ingress nfnetlink_cttimeout vport_gre ip_gre ip_tunnel gre vport_geneve geneve vport_vxlan vxlan ip6_udp_tunnel udp_tunnel openvswitch nf_conncount dm_round_robin dm_service_time dm_multipath xt_nat xt_MASQUERADE nft_chain_nat nf_nat xt_mark xt_conntrack xt_comment nft_compat nft_counter nf_tables nfnetlink ocfs2 ocfs2_nodemanager ocfs2_stackglue iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ipmi_ssif nbd overlay 8021q garp mrp bonding tls rfkill sunrpc ext4 mbcache jbd2 [232066.591052] vfat fat cas_cache cas_disk ses enclosure scsi_transport_sas sg acpi_ipmi ipmi_si ipmi_devintf ipmi_msghandler ip_tables vfio_pci vfio_pci_core vfio_virqfd vfio_iommu_type1 vfio dm_mirror dm_region_hash dm_log dm_mod nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc fuse xfs libcrc32c ast drm_vram_helper qla2xxx drm_kms_helper syscopyarea crct10dif_ce sysfillrect ghash_ce sysimgblt sha2_ce fb_sys_fops cec sha256_arm64 sha1_ce drm_ttm_helper ttm nvme_fc igb sbsa_gwdt nvme_fabrics drm nvme_core i2c_algo_bit i40e scsi_transport_fc megaraid_sas aes_neon_bs [232066.596953] CPU: 6 PID: 4124696 Comm: 10.253.166.125- Kdump: loaded Not tainted 5.15.131-9.cl9_ocfs2.aarch64 #1 [232066.597356] Hardware name: Great Wall .\x93\x8e...RF6260 V5/GWMSSE2GL1T, BIOS T656FBE_V3.0.18 2024-01-06 [232066.597721] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [232066.598034] pc : nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.598327] lr : nfs4_reclaim_open_state+0x12c/0x800 [nfsv4] [232066.598595] sp : ffff8000f568fc70 [232066.598731] x29: ffff8000f568fc70 x28: 0000000000001000 x27: ffff21003db33000 [232066.599030] x26: ffff800005521ae0 x25: ffff0100f98fa3f0 x24: 0000000000000001 [232066.599319] x23: ffff800009920008 x22: ffff21003db33040 x21: ffff21003db33050 [232066.599628] x20: ffff410172fe9e40 x19: ffff410172fe9e00 x18: 0000000000000000 [232066.599914] x17: 0000000000000000 x16: 0000000000000004 x15: 0000000000000000 [232066.600195] x14: 0000000000000000 x13: ffff800008e685a8 x12: 00000000eac0c6e6 [232066.600498] x11: 0000000000000000 x10: 0000000000000008 x9 : ffff8000054e5828 [232066.600784] x8 : 00000000ffffffbf x7 : 0000000000000001 x6 : 000000000a9eb14a [232066.601062] x5 : 0000000000000000 x4 : ffff70ff8a14a800 x3 : 0000000000000058 [232066.601348] x2 : 0000000000000001 x1 : 54dce46366daa6c6 x0 : 0000000000000000 [232066.601636] Call trace: [232066.601749] nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.601998] nfs4_do_reclaim+0x1b8/0x28c [nfsv4] [232066.602218] nfs4_state_manager+0x928/0x10f0 [nfsv4] [232066.602455] nfs4_run_state_manager+0x78/0x1b0 [nfsv4] [232066.602690] kthread+0x110/0x114 [232066.602830] ret_from_fork+0x10/0x20 [232066.602985] Code: 1400000d f9403f20 f9402e61 91016003 (f9402c00) [232066.603284] SMP: stopping secondary CPUs [232066.606936] Starting crashdump kernel... [232066.607146] Bye! Analysing the vmcore, we know that nfs4_copy_state listed by destination nfs_server->ss_copies was added by the field copies in handle_async_copy(), and we found a waiting copy process with the stack as: PID: 3511963 TASK: ffff710028b47e00 CPU: 0 COMMAND: "cp" #0 [ffff8001116ef740] __switch_to at ffff8000081b92f4 #1 [ffff8001116ef760] __schedule at ffff800008dd0650 #2 [ffff8001116ef7c0] schedule at ffff800008dd0a00 #3 [ffff8001116ef7e0] schedule_timeout at ffff800008dd6aa0 #4 [ffff8001116ef860] __wait_for_common at ffff800008dd166c #5 [ffff8001116ef8e0] wait_for_completion_interruptible at ffff800008dd1898 #6 [ffff8001116ef8f0] handle_async_copy at ffff8000055142f4 [nfsv4] #7 [ffff8001116ef970] _nfs42_proc_copy at ffff8000055147c8 [nfsv4] #8 [ffff8001116efa80] nfs42_proc_copy at ffff800005514cf0 [nfsv4] #9 [ffff8001116efc50] __nfs4_copy_file_range.constprop.0 at ffff8000054ed694 [nfsv4] The NULL-pointer dereference was due to nfs42_complete_copies() listed the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state. So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and the data accessed through this pointer was also incorrect. Generally, the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state(). When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED and copies are not deleted in nfs_server->ss_copies, the source state may be passed to the nfs42_complete_copies() process earlier, resulting in this crash scene finally. To solve this issue, we add a list_head nfs_server->ss_src_copies for a server-to-server copy specially. Fixes: 0e65a32 ("NFS: handle source server reboot") Signed-off-by: Yanjun Zhang <zhangyanjun@cestc.cn> Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…tion to perf_sched__replay() [ Upstream commit c690786 ] The start_work_mutex and work_done_wait_mutex are used only for the 'perf sched replay'. Put their initialization in perf_sched__replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.197 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 14.952 MB perf.data (134165 samples) ] # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 65658 nsecs the run test took 999991 nsecs the sleep test took 1079324 nsecs nr_run_events: 42378 nr_sleep_events: 43102 nr_wakeup_events: 31852 target-less wakeups: 17 multi-target wakeups: 712 task 0 ( swapper: 0), nr_events: 10451 task 1 ( swapper: 1), nr_events: 3 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 717 ( sched-messaging: 74483), nr_events: 152 task 718 ( sched-messaging: 74484), nr_events: 1944 task 719 ( sched-messaging: 74485), nr_events: 73 task 720 ( sched-messaging: 74486), nr_events: 163 task 721 ( sched-messaging: 74487), nr_events: 942 task 722 ( sched-messaging: 74488), nr_events: 78 task 723 ( sched-messaging: 74489), nr_events: 1090 ------------------------------------------------------------ #1 : 1366.507, ravg: 1366.51, cpu: 7682.70 / 7682.70 #2 : 1410.072, ravg: 1370.86, cpu: 7723.88 / 7686.82 #3 : 1396.296, ravg: 1373.41, cpu: 7568.20 / 7674.96 #4 : 1381.019, ravg: 1374.17, cpu: 7531.81 / 7660.64 #5 : 1393.826, ravg: 1376.13, cpu: 7725.25 / 7667.11 #6 : 1401.581, ravg: 1378.68, cpu: 7594.82 / 7659.88 #7 : 1381.337, ravg: 1378.94, cpu: 7371.22 / 7631.01 #8 : 1373.842, ravg: 1378.43, cpu: 7894.92 / 7657.40 #9 : 1364.697, ravg: 1377.06, cpu: 7324.91 / 7624.15 #10 : 1363.613, ravg: 1375.72, cpu: 7209.55 / 7582.69 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-2-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

…f_sched__{lat|map|replay}() [ Upstream commit bd2cdf2 ] The curr_pid and cpu_last_switched are used only for the 'perf sched replay/latency/map'. Put their initialization in perf_sched__{lat|map|replay () to reduce unnecessary actions in other commands. Simple functional testing: # perf sched record perf bench sched messaging # Running 'sched/messaging' benchmark: # 20 sender and receiver processes per group # 10 groups == 400 processes run Total time: 0.209 [sec] [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 16.456 MB perf.data (147907 samples) ] # perf sched lat ------------------------------------------------------------------------------------------------------------------------------------------- Task | Runtime ms | Switches | Avg delay ms | Max delay ms | Max delay start | Max delay end | ------------------------------------------------------------------------------------------------------------------------------------------- sched-messaging:(401) | 2990.699 ms | 38705 | avg: 0.661 ms | max: 67.046 ms | max start: 456532.624830 s | max end: 456532.691876 s qemu-system-x86:(7) | 179.764 ms | 2191 | avg: 0.152 ms | max: 21.857 ms | max start: 456532.576434 s | max end: 456532.598291 s sshd:48125 | 0.522 ms | 2 | avg: 0.037 ms | max: 0.046 ms | max start: 456532.514610 s | max end: 456532.514656 s <SNIP> ksoftirqd/11:82 | 0.063 ms | 1 | avg: 0.005 ms | max: 0.005 ms | max start: 456532.769366 s | max end: 456532.769371 s kworker/9:0-mm_:34624 | 0.233 ms | 20 | avg: 0.004 ms | max: 0.007 ms | max start: 456532.690804 s | max end: 456532.690812 s migration/13:93 | 0.000 ms | 1 | avg: 0.004 ms | max: 0.004 ms | max start: 456532.512669 s | max end: 456532.512674 s ----------------------------------------------------------------------------------------------------------------- TOTAL: | 3180.750 ms | 41368 | --------------------------------------------------- # echo $? 0 # perf sched map *A0 456532.510141 secs A0 => migration/0:15 *. 456532.510171 secs . => swapper:0 . *B0 456532.510261 secs B0 => migration/1:21 . *. 456532.510279 secs <SNIP> L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . . 456532.785979 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . . 456532.786054 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . . 456532.786127 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 . 456532.786197 secs L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 L7 *L7 456532.786270 secs # echo $? 0 # perf sched replay run measurement overhead: 108 nsecs sleep measurement overhead: 66473 nsecs the run test took 1000002 nsecs the sleep test took 1082686 nsecs nr_run_events: 49334 nr_sleep_events: 50054 nr_wakeup_events: 34701 target-less wakeups: 165 multi-target wakeups: 766 task 0 ( swapper: 0), nr_events: 15419 task 1 ( swapper: 1), nr_events: 1 task 2 ( swapper: 2), nr_events: 1 <SNIP> task 715 ( sched-messaging: 110248), nr_events: 1438 task 716 ( sched-messaging: 110249), nr_events: 512 task 717 ( sched-messaging: 110250), nr_events: 500 task 718 ( sched-messaging: 110251), nr_events: 537 task 719 ( sched-messaging: 110252), nr_events: 823 ------------------------------------------------------------ #1 : 1325.288, ravg: 1325.29, cpu: 7823.35 / 7823.35 #2 : 1363.606, ravg: 1329.12, cpu: 7655.53 / 7806.56 #3 : 1349.494, ravg: 1331.16, cpu: 7544.80 / 7780.39 #4 : 1311.488, ravg: 1329.19, cpu: 7495.13 / 7751.86 #5 : 1309.902, ravg: 1327.26, cpu: 7266.65 / 7703.34 #6 : 1309.535, ravg: 1325.49, cpu: 7843.86 / 7717.39 #7 : 1316.482, ravg: 1324.59, cpu: 7854.41 / 7731.09 #8 : 1366.604, ravg: 1328.79, cpu: 7955.81 / 7753.57 #9 : 1326.286, ravg: 1328.54, cpu: 7466.86 / 7724.90 #10 : 1356.653, ravg: 1331.35, cpu: 7566.60 / 7709.07 # echo $? 0 Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20240206083228.172607-5-yangjihong1@huawei.com Stable-dep-of: 1a5efc9 ("libsubcmd: Don't free the usage string") Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a848c29 ] On the node of an NFS client, some files saved in the mountpoint of the NFS server were copied to another location of the same NFS server. Accidentally, the nfs42_complete_copies() got a NULL-pointer dereference crash with the following syslog: [232064.838881] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232064.839360] NFSv4: state recovery failed for open file nfs/pvc-12b5200d-cd0f-46a3-b9f0-af8f4fe0ef64.qcow2, error = -116 [232066.588183] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000058 [232066.588586] Mem abort info: [232066.588701] ESR = 0x0000000096000007 [232066.588862] EC = 0x25: DABT (current EL), IL = 32 bits [232066.589084] SET = 0, FnV = 0 [232066.589216] EA = 0, S1PTW = 0 [232066.589340] FSC = 0x07: level 3 translation fault [232066.589559] Data abort info: [232066.589683] ISV = 0, ISS = 0x00000007 [232066.589842] CM = 0, WnR = 0 [232066.589967] user pgtable: 64k pages, 48-bit VAs, pgdp=00002000956ff400 [232066.590231] [0000000000000058] pgd=08001100ae100003, p4d=08001100ae100003, pud=08001100ae100003, pmd=08001100b3c00003, pte=0000000000000000 [232066.590757] Internal error: Oops: 96000007 [#1] SMP [232066.590958] Modules linked in: rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs ocfs2_dlmfs ocfs2_stack_o2cb ocfs2_dlm vhost_net vhost vhost_iotlb tap tun ipt_rpfilter xt_multiport ip_set_hash_ip ip_set_hash_net xfrm_interface xfrm6_tunnel tunnel4 tunnel6 esp4 ah4 wireguard libcurve25519_generic veth xt_addrtype xt_set nf_conntrack_netlink ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_bitmap_port ip_set_hash_ipport dummy ip_set ip_vs_sh ip_vs_wrr ip_vs_rr ip_vs iptable_filter sch_ingress nfnetlink_cttimeout vport_gre ip_gre ip_tunnel gre vport_geneve geneve vport_vxlan vxlan ip6_udp_tunnel udp_tunnel openvswitch nf_conncount dm_round_robin dm_service_time dm_multipath xt_nat xt_MASQUERADE nft_chain_nat nf_nat xt_mark xt_conntrack xt_comment nft_compat nft_counter nf_tables nfnetlink ocfs2 ocfs2_nodemanager ocfs2_stackglue iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ipmi_ssif nbd overlay 8021q garp mrp bonding tls rfkill sunrpc ext4 mbcache jbd2 [232066.591052] vfat fat cas_cache cas_disk ses enclosure scsi_transport_sas sg acpi_ipmi ipmi_si ipmi_devintf ipmi_msghandler ip_tables vfio_pci vfio_pci_core vfio_virqfd vfio_iommu_type1 vfio dm_mirror dm_region_hash dm_log dm_mod nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 br_netfilter bridge stp llc fuse xfs libcrc32c ast drm_vram_helper qla2xxx drm_kms_helper syscopyarea crct10dif_ce sysfillrect ghash_ce sysimgblt sha2_ce fb_sys_fops cec sha256_arm64 sha1_ce drm_ttm_helper ttm nvme_fc igb sbsa_gwdt nvme_fabrics drm nvme_core i2c_algo_bit i40e scsi_transport_fc megaraid_sas aes_neon_bs [232066.596953] CPU: 6 PID: 4124696 Comm: 10.253.166.125- Kdump: loaded Not tainted 5.15.131-9.cl9_ocfs2.aarch64 #1 [232066.597356] Hardware name: Great Wall .\x93\x8e...RF6260 V5/GWMSSE2GL1T, BIOS T656FBE_V3.0.18 2024-01-06 [232066.597721] pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [232066.598034] pc : nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.598327] lr : nfs4_reclaim_open_state+0x12c/0x800 [nfsv4] [232066.598595] sp : ffff8000f568fc70 [232066.598731] x29: ffff8000f568fc70 x28: 0000000000001000 x27: ffff21003db33000 [232066.599030] x26: ffff800005521ae0 x25: ffff0100f98fa3f0 x24: 0000000000000001 [232066.599319] x23: ffff800009920008 x22: ffff21003db33040 x21: ffff21003db33050 [232066.599628] x20: ffff410172fe9e40 x19: ffff410172fe9e00 x18: 0000000000000000 [232066.599914] x17: 0000000000000000 x16: 0000000000000004 x15: 0000000000000000 [232066.600195] x14: 0000000000000000 x13: ffff800008e685a8 x12: 00000000eac0c6e6 [232066.600498] x11: 0000000000000000 x10: 0000000000000008 x9 : ffff8000054e5828 [232066.600784] x8 : 00000000ffffffbf x7 : 0000000000000001 x6 : 000000000a9eb14a [232066.601062] x5 : 0000000000000000 x4 : ffff70ff8a14a800 x3 : 0000000000000058 [232066.601348] x2 : 0000000000000001 x1 : 54dce46366daa6c6 x0 : 0000000000000000 [232066.601636] Call trace: [232066.601749] nfs4_reclaim_open_state+0x220/0x800 [nfsv4] [232066.601998] nfs4_do_reclaim+0x1b8/0x28c [nfsv4] [232066.602218] nfs4_state_manager+0x928/0x10f0 [nfsv4] [232066.602455] nfs4_run_state_manager+0x78/0x1b0 [nfsv4] [232066.602690] kthread+0x110/0x114 [232066.602830] ret_from_fork+0x10/0x20 [232066.602985] Code: 1400000d f9403f20 f9402e61 91016003 (f9402c00) [232066.603284] SMP: stopping secondary CPUs [232066.606936] Starting crashdump kernel... [232066.607146] Bye! Analysing the vmcore, we know that nfs4_copy_state listed by destination nfs_server->ss_copies was added by the field copies in handle_async_copy(), and we found a waiting copy process with the stack as: PID: 3511963 TASK: ffff710028b47e00 CPU: 0 COMMAND: "cp" #0 [ffff8001116ef740] __switch_to at ffff8000081b92f4 #1 [ffff8001116ef760] __schedule at ffff800008dd0650 #2 [ffff8001116ef7c0] schedule at ffff800008dd0a00 #3 [ffff8001116ef7e0] schedule_timeout at ffff800008dd6aa0 #4 [ffff8001116ef860] __wait_for_common at ffff800008dd166c #5 [ffff8001116ef8e0] wait_for_completion_interruptible at ffff800008dd1898 #6 [ffff8001116ef8f0] handle_async_copy at ffff8000055142f4 [nfsv4] #7 [ffff8001116ef970] _nfs42_proc_copy at ffff8000055147c8 [nfsv4] #8 [ffff8001116efa80] nfs42_proc_copy at ffff800005514cf0 [nfsv4] #9 [ffff8001116efc50] __nfs4_copy_file_range.constprop.0 at ffff8000054ed694 [nfsv4] The NULL-pointer dereference was due to nfs42_complete_copies() listed the nfs_server->ss_copies by the field ss_copies of nfs4_copy_state. So the nfs4_copy_state address ffff0100f98fa3f0 was offset by 0x10 and the data accessed through this pointer was also incorrect. Generally, the ordered list nfs4_state_owner->so_states indicate open(O_RDWR) or open(O_WRITE) states are reclaimed firstly by nfs4_reclaim_open_state(). When destination state reclaim is failed with NFS_STATE_RECOVERY_FAILED and copies are not deleted in nfs_server->ss_copies, the source state may be passed to the nfs42_complete_copies() process earlier, resulting in this crash scene finally. To solve this issue, we add a list_head nfs_server->ss_src_copies for a server-to-server copy specially. Fixes: 0e65a32 ("NFS: handle source server reboot") Signed-off-by: Yanjun Zhang <zhangyanjun@cestc.cn> Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…ation commit c728a95 upstream. When testing the XDP_REDIRECT function on the LS1028A platform, we found a very reproducible issue that the Tx frames can no longer be sent out even if XDP_REDIRECT is turned off. Specifically, if there is a lot of traffic on Rx direction, when XDP_REDIRECT is turned on, the console may display some warnings like "timeout for tx ring #6 clear", and all redirected frames will be dropped, the detailed log is as follows. root@ls1028ardb:~# ./xdp-bench redirect eno0 eno2 Redirecting from eno0 (ifindex 3; driver fsl_enetc) to eno2 (ifindex 4; driver fsl_enetc) [203.849809] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #5 clear [204.006051] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #6 clear [204.161944] fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #7 clear eno0->eno2 1420505 rx/s 1420590 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420590 drop/s 0 drv_err/s 15.71 bulk-avg eno0->eno2 1420484 rx/s 1420485 err,drop/s 0 xmit/s xmit eno0->eno2 0 xmit/s 1420485 drop/s 0 drv_err/s 15.71 bulk-avg By analyzing the XDP_REDIRECT implementation of enetc driver, the driver will reconfigure Tx and Rx BD rings when a bpf program is installed or uninstalled, but there is no mechanisms to block the redirected frames when enetc driver reconfigures rings. Similarly, XDP_TX verdicts on received frames can also lead to frames being enqueued in the Tx rings. Because XDP ignores the state set by the netif_tx_wake_queue() API, so introduce the ENETC_TX_DOWN flag to suppress transmission of XDP frames. Fixes: c33bfaf ("net: enetc: set up XDP program under enetc_reconfigure()") Cc: stable@vger.kernel.org Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20241010092056.298128-3-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0a93f2c upstream. The Tx BD rings are disabled first in enetc_stop() and the driver waits for them to become empty. This operation is not safe while the ring is actively transmitting frames, and will cause the ring to not be empty and hardware exception. As described in the NETC block guide, software should only disable an active Tx ring after all pending ring entries have been consumed (i.e. when PI = CI). Disabling a transmit ring that is actively processing BDs risks a HW-SW race hazard whereby a hardware resource becomes assigned to work on one or more ring entries only to have those entries be removed due to the ring becoming disabled. When testing XDP_REDIRECT feautre, although all frames were blocked from being put into Tx rings during ring reconfiguration, the similar warning log was still encountered: fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #6 clear fsl_enetc 0000:00:00.2 eno2: timeout for tx ring #7 clear The reason is that when there are still unsent frames in the Tx ring, disabling the Tx ring causes the remaining frames to be unable to be sent out. And the Tx ring cannot be restored, which means that even if the xdp program is uninstalled, the Tx frames cannot be sent out anymore. Therefore, correct the operation order in enect_start() and enect_stop(). Fixes: ff58fda ("net: enetc: prioritize ability to go down over packet processing") Cc: stable@vger.kernel.org Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://patch.msgid.link/20241010092056.298128-4-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cf96b8e upstream. ASan reports a memory leak caused by evlist not being deleted on exit in perf-report, perf-script and perf-data. The problem is caused by evlist->session not being deleted, which is allocated in perf_session__read_header, called in perf_session__new if perf_data is in read mode. In case of write mode, the session->evlist is filled by the caller. This patch solves the problem by calling evlist__delete in perf_session__delete if perf_data is in read mode. Changes in v2: - call evlist__delete from within perf_session__delete v1: https://lore.kernel.org/lkml/20210621234317.235545-1-rickyman7@gmail.com/ ASan report follows: $ ./perf script report flamegraph ================================================================= ==227640==ERROR: LeakSanitizer: detected memory leaks <SNIP unrelated> Indirect leak of 2704 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0x7f999e in evlist__new /home/user/linux/tools/perf/util/evlist.c:77:26 #3 0x8ad938 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3797:20 #4 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #5 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #6 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #7 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #8 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #9 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #10 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #11 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 568 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0x80ce88 in evsel__new_idx /home/user/linux/tools/perf/util/evsel.c:268:24 #3 0x8aed93 in evsel__new /home/user/linux/tools/perf/util/evsel.h:210:9 #4 0x8ae07e in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3853:11 #5 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #6 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #7 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #8 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #9 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #10 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #11 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #12 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 264 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0xbe3e70 in xyarray__new /home/user/linux/tools/lib/perf/xyarray.c:10:23 #3 0xbd7754 in perf_evsel__alloc_id /home/user/linux/tools/lib/perf/evsel.c:361:21 #4 0x8ae201 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3871:7 #5 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #6 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #7 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #8 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #9 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #10 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #11 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #12 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 32 byte(s) in 1 object(s) allocated from: #0 0x4f4137 in calloc (/home/user/linux/tools/perf/perf+0x4f4137) #1 0xbe3d56 in zalloc /home/user/linux/tools/lib/perf/../../lib/zalloc.c:8:9 #2 0xbd77e0 in perf_evsel__alloc_id /home/user/linux/tools/lib/perf/evsel.c:365:14 #3 0x8ae201 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3871:7 #4 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #5 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #6 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #7 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #8 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #9 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #10 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #11 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) Indirect leak of 7 byte(s) in 1 object(s) allocated from: #0 0x4b8207 in strdup (/home/user/linux/tools/perf/perf+0x4b8207) #1 0x8b4459 in evlist__set_event_name /home/user/linux/tools/perf/util/header.c:2292:16 #2 0x89d862 in process_event_desc /home/user/linux/tools/perf/util/header.c:2313:3 #3 0x8af319 in perf_file_section__process /home/user/linux/tools/perf/util/header.c:3651:9 #4 0x8aa6e9 in perf_header__process_sections /home/user/linux/tools/perf/util/header.c:3427:9 #5 0x8ae3e7 in perf_session__read_header /home/user/linux/tools/perf/util/header.c:3886:2 #6 0x8ec714 in perf_session__open /home/user/linux/tools/perf/util/session.c:109:6 #7 0x8ebe83 in perf_session__new /home/user/linux/tools/perf/util/session.c:213:10 #8 0x60c6de in cmd_script /home/user/linux/tools/perf/builtin-script.c:3856:12 #9 0x7b2930 in run_builtin /home/user/linux/tools/perf/perf.c:313:11 #10 0x7b120f in handle_internal_command /home/user/linux/tools/perf/perf.c:365:8 #11 0x7b2493 in run_argv /home/user/linux/tools/perf/perf.c:409:2 #12 0x7b0c89 in main /home/user/linux/tools/perf/perf.c:539:3 #13 0x7f5260654b74 (/lib64/libc.so.6+0x27b74) SUMMARY: AddressSanitizer: 3728 byte(s) leaked in 7 allocation(s). Signed-off-by: Riccardo Mancini <rickyman7@gmail.com> Acked-by: Ian Rogers <irogers@google.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20210624231926.212208-1-rickyman7@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: stable@vger.kernel.org # 5.10.228 Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 3f23f96 ] BUG: KASAN: slab-use-after-free in tcp_write_timer_handler+0x156/0x3e0 Read of size 1 at addr ffff888111f322cd by task swapper/0/0 CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted 6.12.0-rc4-dirty #7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 Call Trace: <IRQ> dump_stack_lvl+0x68/0xa0 print_address_description.constprop.0+0x2c/0x3d0 print_report+0xb4/0x270 kasan_report+0xbd/0xf0 tcp_write_timer_handler+0x156/0x3e0 tcp_write_timer+0x66/0x170 call_timer_fn+0xfb/0x1d0 __run_timers+0x3f8/0x480 run_timer_softirq+0x9b/0x100 handle_softirqs+0x153/0x390 __irq_exit_rcu+0x103/0x120 irq_exit_rcu+0xe/0x20 sysvec_apic_timer_interrupt+0x76/0x90 </IRQ> <TASK> asm_sysvec_apic_timer_interrupt+0x1a/0x20 RIP: 0010:default_idle+0xf/0x20 Code: 4c 01 c7 4c 29 c2 e9 72 ff ff ff 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 f3 0f 1e fa 66 90 0f 00 2d 33 f8 25 00 fb f4 <fa> c3 cc cc cc cc 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 RSP: 0018:ffffffffa2007e28 EFLAGS: 00000242 RAX: 00000000000f3b31 RBX: 1ffffffff4400fc7 RCX: ffffffffa09c3196 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff9f00590f RBP: 0000000000000000 R08: 0000000000000001 R09: ffffed102360835d R10: ffff88811b041aeb R11: 0000000000000001 R12: 0000000000000000 R13: ffffffffa202d7c0 R14: 0000000000000000 R15: 00000000000147d0 default_idle_call+0x6b/0xa0 cpuidle_idle_call+0x1af/0x1f0 do_idle+0xbc/0x130 cpu_startup_entry+0x33/0x40 rest_init+0x11f/0x210 start_kernel+0x39a/0x420 x86_64_start_reservations+0x18/0x30 x86_64_start_kernel+0x97/0xa0 common_startup_64+0x13e/0x141 </TASK> Allocated by task 595: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 __kasan_slab_alloc+0x87/0x90 kmem_cache_alloc_noprof+0x12b/0x3f0 copy_net_ns+0x94/0x380 create_new_namespaces+0x24c/0x500 unshare_nsproxy_namespaces+0x75/0xf0 ksys_unshare+0x24e/0x4f0 __x64_sys_unshare+0x1f/0x30 do_syscall_64+0x70/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e Freed by task 100: kasan_save_stack+0x24/0x50 kasan_save_track+0x14/0x30 kasan_save_free_info+0x3b/0x60 __kasan_slab_free+0x54/0x70 kmem_cache_free+0x156/0x5d0 cleanup_net+0x5d3/0x670 process_one_work+0x776/0xa90 worker_thread+0x2e2/0x560 kthread+0x1a8/0x1f0 ret_from_fork+0x34/0x60 ret_from_fork_asm+0x1a/0x30 Reproduction script: mkdir -p /mnt/nfsshare mkdir -p /mnt/nfs/netns_1 mkfs.ext4 /dev/sdb mount /dev/sdb /mnt/nfsshare systemctl restart nfs-server chmod 777 /mnt/nfsshare exportfs -i -o rw,no_root_squash *:/mnt/nfsshare ip netns add netns_1 ip link add name veth_1_peer type veth peer veth_1 ifconfig veth_1_peer 11.11.0.254 up ip link set veth_1 netns netns_1 ip netns exec netns_1 ifconfig veth_1 11.11.0.1 ip netns exec netns_1 /root/iptables -A OUTPUT -d 11.11.0.254 -p tcp \ --tcp-flags FIN FIN -j DROP (note: In my environment, a DESTROY_CLIENTID operation is always sent immediately, breaking the nfs tcp connection.) ip netns exec netns_1 timeout -s 9 300 mount -t nfs -o proto=tcp,vers=4.1 \ 11.11.0.254:/mnt/nfsshare /mnt/nfs/netns_1 ip netns del netns_1 The reason here is that the tcp socket in netns_1 (nfs side) has been shutdown and closed (done in xs_destroy), but the FIN message (with ack) is discarded, and the nfsd side keeps sending retransmission messages. As a result, when the tcp sock in netns_1 processes the received message, it sends the message (FIN message) in the sending queue, and the tcp timer is re-established. When the network namespace is deleted, the net structure accessed by tcp's timer handler function causes problems. To fix this problem, let's hold netns refcnt for the tcp kernel socket as done in other modules. This is an ugly hack which can easily be backported to earlier kernels. A proper fix which cleans up the interfaces will follow, but may not be so easy to backport. Fixes: 26abe14 ("net: Modify sk_alloc to not reference count the netns of kernel sockets.") Signed-off-by: Liu Jian <liujian56@huawei.com> Acked-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6a2fa13 ] syzkaller reported a use-after-free of UDP kernel socket in cleanup_bearer() without repro. [0][1] When bearer_disable() calls tipc_udp_disable(), cleanup of the UDP kernel socket is deferred by work calling cleanup_bearer(). tipc_net_stop() waits for such works to finish by checking tipc_net(net)->wq_count. However, the work decrements the count too early before releasing the kernel socket, unblocking cleanup_net() and resulting in use-after-free. Let's move the decrement after releasing the socket in cleanup_bearer(). [0]: ref_tracker: net notrefcnt@000000009b3d1faf has 1/1 users at sk_alloc+0x438/0x608 inet_create+0x4c8/0xcb0 __sock_create+0x350/0x6b8 sock_create_kern+0x58/0x78 udp_sock_create4+0x68/0x398 udp_sock_create+0x88/0xc8 tipc_udp_enable+0x5e8/0x848 __tipc_nl_bearer_enable+0x84c/0xed8 tipc_nl_bearer_enable+0x38/0x60 genl_family_rcv_msg_doit+0x170/0x248 genl_rcv_msg+0x400/0x5b0 netlink_rcv_skb+0x1dc/0x398 genl_rcv+0x44/0x68 netlink_unicast+0x678/0x8b0 netlink_sendmsg+0x5e4/0x898 ____sys_sendmsg+0x500/0x830 [1]: BUG: KMSAN: use-after-free in udp_hashslot include/net/udp.h:85 [inline] BUG: KMSAN: use-after-free in udp_lib_unhash+0x3b8/0x930 net/ipv4/udp.c:1979 udp_hashslot include/net/udp.h:85 [inline] udp_lib_unhash+0x3b8/0x930 net/ipv4/udp.c:1979 sk_common_release+0xaf/0x3f0 net/core/sock.c:3820 inet_release+0x1e0/0x260 net/ipv4/af_inet.c:437 inet6_release+0x6f/0xd0 net/ipv6/af_inet6.c:489 __sock_release net/socket.c:658 [inline] sock_release+0xa0/0x210 net/socket.c:686 cleanup_bearer+0x42d/0x4c0 net/tipc/udp_media.c:819 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xcaf/0x1c90 kernel/workqueue.c:3310 worker_thread+0xf6c/0x1510 kernel/workqueue.c:3391 kthread+0x531/0x6b0 kernel/kthread.c:389 ret_from_fork+0x60/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:244 Uninit was created at: slab_free_hook mm/slub.c:2269 [inline] slab_free mm/slub.c:4580 [inline] kmem_cache_free+0x207/0xc40 mm/slub.c:4682 net_free net/core/net_namespace.c:454 [inline] cleanup_net+0x16f2/0x19d0 net/core/net_namespace.c:647 process_one_work kernel/workqueue.c:3229 [inline] process_scheduled_works+0xcaf/0x1c90 kernel/workqueue.c:3310 worker_thread+0xf6c/0x1510 kernel/workqueue.c:3391 kthread+0x531/0x6b0 kernel/kthread.c:389 ret_from_fork+0x60/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:244 CPU: 0 UID: 0 PID: 54 Comm: kworker/0:2 Not tainted 6.12.0-rc1-00131-gf66ebf37d69c #7 91723d6f74857f70725e1583cba3cf4adc716cfa Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014 Workqueue: events cleanup_bearer Fixes: 26abe14 ("net: Modify sk_alloc to not reference count the netns of kernel sockets.") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://patch.msgid.link/20241127050512.28438-1-kuniyu@amazon.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

…le_direct_reclaim() commit 6aaced5 upstream. The task sometimes continues looping in throttle_direct_reclaim() because allow_direct_reclaim(pgdat) keeps returning false. #0 [ffff80002cb6f8d0] __switch_to at ffff8000080095ac #1 [ffff80002cb6f900] __schedule at ffff800008abbd1c #2 [ffff80002cb6f990] schedule at ffff800008abc50c #3 [ffff80002cb6f9b0] throttle_direct_reclaim at ffff800008273550 #4 [ffff80002cb6fa20] try_to_free_pages at ffff800008277b68 #5 [ffff80002cb6fae0] __alloc_pages_nodemask at ffff8000082c4660 #6 [ffff80002cb6fc50] alloc_pages_vma at ffff8000082e4a98 #7 [ffff80002cb6fca0] do_anonymous_page at ffff80000829f5a8 #8 [ffff80002cb6fce0] __handle_mm_fault at ffff8000082a5974 #9 [ffff80002cb6fd90] handle_mm_fault at ffff8000082a5bd4 At this point, the pgdat contains the following two zones: NODE: 4 ZONE: 0 ADDR: ffff00817fffe540 NAME: "DMA32" SIZE: 20480 MIN/LOW/HIGH: 11/28/45 VM_STAT: NR_FREE_PAGES: 359 NR_ZONE_INACTIVE_ANON: 18813 NR_ZONE_ACTIVE_ANON: 0 NR_ZONE_INACTIVE_FILE: 50 NR_ZONE_ACTIVE_FILE: 0 NR_ZONE_UNEVICTABLE: 0 NR_ZONE_WRITE_PENDING: 0 NR_MLOCK: 0 NR_BOUNCE: 0 NR_ZSPAGES: 0 NR_FREE_CMA_PAGES: 0 NODE: 4 ZONE: 1 ADDR: ffff00817fffec00 NAME: "Normal" SIZE: 8454144 PRESENT: 98304 MIN/LOW/HIGH: 68/166/264 VM_STAT: NR_FREE_PAGES: 146 NR_ZONE_INACTIVE_ANON: 94668 NR_ZONE_ACTIVE_ANON: 3 NR_ZONE_INACTIVE_FILE: 735 NR_ZONE_ACTIVE_FILE: 78 NR_ZONE_UNEVICTABLE: 0 NR_ZONE_WRITE_PENDING: 0 NR_MLOCK: 0 NR_BOUNCE: 0 NR_ZSPAGES: 0 NR_FREE_CMA_PAGES: 0 In allow_direct_reclaim(), while processing ZONE_DMA32, the sum of inactive/active file-backed pages calculated in zone_reclaimable_pages() based on the result of zone_page_state_snapshot() is zero. Additionally, since this system lacks swap, the calculation of inactive/ active anonymous pages is skipped. crash> p nr_swap_pages nr_swap_pages = $1937 = { counter = 0 } As a result, ZONE_DMA32 is deemed unreclaimable and skipped, moving on to the processing of the next zone, ZONE_NORMAL, despite ZONE_DMA32 having free pages significantly exceeding the high watermark. The problem is that the pgdat->kswapd_failures hasn't been incremented. crash> px ((struct pglist_data *) 0xffff00817fffe540)->kswapd_failures $1935 = 0x0 This is because the node deemed balanced. The node balancing logic in balance_pgdat() evaluates all zones collectively. If one or more zones (e.g., ZONE_DMA32) have enough free pages to meet their watermarks, the entire node is deemed balanced. This causes balance_pgdat() to exit early before incrementing the kswapd_failures, as it considers the overall memory state acceptable, even though some zones (like ZONE_NORMAL) remain under significant pressure. The patch ensures that zone_reclaimable_pages() includes free pages (NR_FREE_PAGES) in its calculation when no other reclaimable pages are available (e.g., file-backed or anonymous pages). This change prevents zones like ZONE_DMA32, which have sufficient free pages, from being mistakenly deemed unreclaimable. By doing so, the patch ensures proper node balancing, avoids masking pressure on other zones like ZONE_NORMAL, and prevents infinite loops in throttle_direct_reclaim() caused by allow_direct_reclaim(pgdat) repeatedly returning false. The kernel hangs due to a task stuck in throttle_direct_reclaim(), caused by a node being incorrectly deemed balanced despite pressure in certain zones, such as ZONE_NORMAL. This issue arises from zone_reclaimable_pages() returning 0 for zones without reclaimable file- backed or anonymous pages, causing zones like ZONE_DMA32 with sufficient free pages to be skipped. The lack of swap or reclaimable pages results in ZONE_DMA32 being ignored during reclaim, masking pressure in other zones. Consequently, pgdat->kswapd_failures remains 0 in balance_pgdat(), preventing fallback mechanisms in allow_direct_reclaim() from being triggered, leading to an infinite loop in throttle_direct_reclaim(). This patch modifies zone_reclaimable_pages() to account for free pages (NR_FREE_PAGES) when no other reclaimable pages exist. This ensures zones with sufficient free pages are not skipped, enabling proper balancing and reclaim behavior. [akpm@linux-foundation.org: coding-style cleanups] Link: https://lkml.kernel.org/r/20241130164346.436469-1-snishika@redhat.com Link: https://lkml.kernel.org/r/20241130161236.433747-2-snishika@redhat.com Fixes: 5a1c84b ("mm: remove reclaim and compaction retry approximations") Signed-off-by: Seiji Nishikawa <snishika@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 59d9094 ] The folio refcount may be increased unexpectly through try_get_folio() by caller such as split_huge_pages. In huge_pmd_unshare(), we use refcount to check whether a pmd page table is shared. The check is incorrect if the refcount is increased by the above caller, and this can cause the page table leaked: BUG: Bad page state in process sh pfn:109324 page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x66 pfn:0x109324 flags: 0x17ffff800000000(node=0|zone=2|lastcpupid=0xfffff) page_type: f2(table) raw: 017ffff800000000 0000000000000000 0000000000000000 0000000000000000 raw: 0000000000000066 0000000000000000 00000000f2000000 0000000000000000 page dumped because: nonzero mapcount ... CPU: 31 UID: 0 PID: 7515 Comm: sh Kdump: loaded Tainted: G B 6.13.0-rc2master+ #7 Tainted: [B]=BAD_PAGE Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 Call trace: show_stack+0x20/0x38 (C) dump_stack_lvl+0x80/0xf8 dump_stack+0x18/0x28 bad_page+0x8c/0x130 free_page_is_bad_report+0xa4/0xb0 free_unref_page+0x3cc/0x620 __folio_put+0xf4/0x158 split_huge_pages_all+0x1e0/0x3e8 split_huge_pages_write+0x25c/0x2d8 full_proxy_write+0x64/0xd8 vfs_write+0xcc/0x280 ksys_write+0x70/0x110 __arm64_sys_write+0x24/0x38 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x34/0x128 el0t_64_sync_handler+0xc8/0xd0 el0t_64_sync+0x190/0x198 The issue may be triggered by damon, offline_page, page_idle, etc, which will increase the refcount of page table. 1. The page table itself will be discarded after reporting the "nonzero mapcount". 2. The HugeTLB page mapped by the page table miss freeing since we treat the page table as shared and a shared page table will not be unmapped. Fix it by introducing independent PMD page table shared count. As described by comment, pt_index/pt_mm/pt_frag_refcount are used for s390 gmap, x86 pgds and powerpc, pt_share_count is used for x86/arm64/riscv pmds, so we can reuse the field as pt_share_count. Link: https://lkml.kernel.org/r/20241216071147.3984217-1-liushixin2@huawei.com Fixes: 39dde65 ("[PATCH] shared page table for hugetlb page") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Ken Chen <kenneth.w.chen@intel.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nanyong Sun <sunnanyong@huawei.com> Cc: Jane Chu <jane.chu@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c7b87ce ] libtraceevent parses and returns an array of argument fields, sometimes larger than RAW_SYSCALL_ARGS_NUM (6) because it includes "__syscall_nr", idx will traverse to index 6 (7th element) whereas sc->fmt->arg holds 6 elements max, creating an out-of-bounds access. This runtime error is found by UBsan. The error message: $ sudo UBSAN_OPTIONS=print_stacktrace=1 ./perf trace -a --max-events=1 builtin-trace.c:1966:35: runtime error: index 6 out of bounds for type 'syscall_arg_fmt [6]' #0 0x5c04956be5fe in syscall__alloc_arg_fmts /home/howard/hw/linux-perf/tools/perf/builtin-trace.c:1966 #1 0x5c04956c0510 in trace__read_syscall_info /home/howard/hw/linux-perf/tools/perf/builtin-trace.c:2110 #2 0x5c04956c372b in trace__syscall_info /home/howard/hw/linux-perf/tools/perf/builtin-trace.c:2436 #3 0x5c04956d2f39 in trace__init_syscalls_bpf_prog_array_maps /home/howard/hw/linux-perf/tools/perf/builtin-trace.c:3897 #4 0x5c04956d6d25 in trace__run /home/howard/hw/linux-perf/tools/perf/builtin-trace.c:4335 #5 0x5c04956e112e in cmd_trace /home/howard/hw/linux-perf/tools/perf/builtin-trace.c:5502 #6 0x5c04956eda7d in run_builtin /home/howard/hw/linux-perf/tools/perf/perf.c:351 #7 0x5c04956ee0a8 in handle_internal_command /home/howard/hw/linux-perf/tools/perf/perf.c:404 #8 0x5c04956ee37f in run_argv /home/howard/hw/linux-perf/tools/perf/perf.c:448 #9 0x5c04956ee8e9 in main /home/howard/hw/linux-perf/tools/perf/perf.c:556 #10 0x79eb3622a3b7 in __libc_start_call_main ../sysdeps/nptl/libc_start_call_main.h:58 #11 0x79eb3622a47a in __libc_start_main_impl ../csu/libc-start.c:360 #12 0x5c04955422d4 in _start (/home/howard/hw/linux-perf/tools/perf/perf+0x4e02d4) (BuildId: 5b6cab2d59e96a4341741765ad6914a4d784dbc6) 0.000 ( 0.014 ms): Chrome_ChildIO/117244 write(fd: 238, buf: !, count: 1) = 1 Fixes: 5e58fcf ("perf trace: Allow allocating sc->arg_fmt even without the syscall tracepoint") Signed-off-by: Howard Chu <howardchu95@gmail.com> Link: https://lore.kernel.org/r/20250122025519.361873-1-howardchu95@gmail.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 5858b68 upstream. Kernel will hang on destroy admin_q while we create ctrl failed, such as following calltrace: PID: 23644 TASK: ff2d52b40f439fc0 CPU: 2 COMMAND: "nvme" #0 [ff61d23de260fb78] __schedule at ffffffff8323bc15 #1 [ff61d23de260fc08] schedule at ffffffff8323c014 #2 [ff61d23de260fc28] blk_mq_freeze_queue_wait at ffffffff82a3dba1 #3 [ff61d23de260fc78] blk_freeze_queue at ffffffff82a4113a #4 [ff61d23de260fc90] blk_cleanup_queue at ffffffff82a33006 #5 [ff61d23de260fcb0] nvme_rdma_destroy_admin_queue at ffffffffc12686ce #6 [ff61d23de260fcc8] nvme_rdma_setup_ctrl at ffffffffc1268ced #7 [ff61d23de260fd28] nvme_rdma_create_ctrl at ffffffffc126919b #8 [ff61d23de260fd68] nvmf_dev_write at ffffffffc024f362 #9 [ff61d23de260fe38] vfs_write at ffffffff827d5f25 RIP: 00007fda7891d574 RSP: 00007ffe2ef06958 RFLAGS: 00000202 RAX: ffffffffffffffda RBX: 000055e8122a4d90 RCX: 00007fda7891d574 RDX: 000000000000012b RSI: 000055e8122a4d90 RDI: 0000000000000004 RBP: 00007ffe2ef079c0 R8: 000000000000012b R9: 000055e8122a4d90 R10: 0000000000000000 R11: 0000000000000202 R12: 0000000000000004 R13: 000055e8122923c0 R14: 000000000000012b R15: 00007fda78a54500 ORIG_RAX: 0000000000000001 CS: 0033 SS: 002b This due to we have quiesced admi_q before cancel requests, but forgot to unquiesce before destroy it, as a result we fail to drain the pending requests, and hang on blk_mq_freeze_queue_wait() forever. Here try to reuse nvme_rdma_teardown_admin_queue() to fix this issue and simplify the code. Fixes: 958dc1d ("nvme-rdma: add clean action for failed reconnection") Reported-by: Yingfu.zhou <yingfu.zhou@shopee.com> Signed-off-by: Chunguang.xu <chunguang.xu@shopee.com> Signed-off-by: Yue.zhao <yue.zhao@shopee.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> [Minor context change fixed] Signed-off-by: Feng Liu <Feng.Liu3@windriver.com> Signed-off-by: He Zhe <Zhe.He@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 88f7f56 ] When a bio with REQ_PREFLUSH is submitted to dm, __send_empty_flush() generates a flush_bio with REQ_OP_WRITE | REQ_PREFLUSH | REQ_SYNC, which causes the flush_bio to be throttled by wbt_wait(). An example from v5.4, similar problem also exists in upstream: crash> bt 2091206 PID: 2091206 TASK: ffff2050df92a300 CPU: 109 COMMAND: "kworker/u260:0" #0 [ffff800084a2f7f0] __switch_to at ffff80004008aeb8 #1 [ffff800084a2f820] __schedule at ffff800040bfa0c4 #2 [ffff800084a2f880] schedule at ffff800040bfa4b4 #3 [ffff800084a2f8a0] io_schedule at ffff800040bfa9c4 #4 [ffff800084a2f8c0] rq_qos_wait at ffff8000405925bc #5 [ffff800084a2f940] wbt_wait at ffff8000405bb3a0 #6 [ffff800084a2f9a0] __rq_qos_throttle at ffff800040592254 #7 [ffff800084a2f9c0] blk_mq_make_request at ffff80004057cf38 #8 [ffff800084a2fa60] generic_make_request at ffff800040570138 #9 [ffff800084a2fae0] submit_bio at ffff8000405703b4 #10 [ffff800084a2fb50] xlog_write_iclog at ffff800001280834 [xfs] #11 [ffff800084a2fbb0] xlog_sync at ffff800001280c3c [xfs] #12 [ffff800084a2fbf0] xlog_state_release_iclog at ffff800001280df4 [xfs] #13 [ffff800084a2fc10] xlog_write at ffff80000128203c [xfs] #14 [ffff800084a2fcd0] xlog_cil_push at ffff8000012846dc [xfs] #15 [ffff800084a2fda0] xlog_cil_push_work at ffff800001284a2c [xfs] #16 [ffff800084a2fdb0] process_one_work at ffff800040111d08 #17 [ffff800084a2fe00] worker_thread at ffff8000401121cc #18 [ffff800084a2fe70] kthread at ffff800040118de4 After commit 2def284 ("xfs: don't allow log IO to be throttled"), the metadata submitted by xlog_write_iclog() should not be throttled. But due to the existence of the dm layer, throttling flush_bio indirectly causes the metadata bio to be throttled. Fix this by conditionally adding REQ_IDLE to flush_bio.bi_opf, which makes wbt_should_throttle() return false to avoid wbt_wait(). Signed-off-by: Jinliang Zheng <alexjlzheng@tencent.com> Reviewed-by: Tianxiang Peng <txpeng@tencent.com> Reviewed-by: Hao Peng <flyingpeng@tencent.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ee684de ] As shown in [1], it is possible to corrupt a BPF ELF file such that arbitrary BPF instructions are loaded by libbpf. This can be done by setting a symbol (BPF program) section offset to a large (unsigned) number such that <section start + symbol offset> overflows and points before the section data in the memory. Consider the situation below where: - prog_start = sec_start + symbol_offset <-- size_t overflow here - prog_end = prog_start + prog_size prog_start sec_start prog_end sec_end | | | | v v v v .....................|################################|............ The report in [1] also provides a corrupted BPF ELF which can be used as a reproducer: $ readelf -S crash Section Headers: [Nr] Name Type Address Offset Size EntSize Flags Link Info Align ... [ 2] uretprobe.mu[...] PROGBITS 0000000000000000 00000040 0000000000000068 0000000000000000 AX 0 0 8 $ readelf -s crash Symbol table '.symtab' contains 8 entries: Num: Value Size Type Bind Vis Ndx Name ... 6: ffffffffffffffb8 104 FUNC GLOBAL DEFAULT 2 handle_tp Here, the handle_tp prog has section offset ffffffffffffffb8, i.e. will point before the actual memory where section 2 is allocated. This is also reported by AddressSanitizer: ================================================================= ==1232==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x7c7302fe0000 at pc 0x7fc3046e4b77 bp 0x7ffe64677cd0 sp 0x7ffe64677490 READ of size 104 at 0x7c7302fe0000 thread T0 #0 0x7fc3046e4b76 in memcpy (/lib64/libasan.so.8+0xe4b76) #1 0x00000040df3e in bpf_object__init_prog /src/libbpf/src/libbpf.c:856 #2 0x00000040df3e in bpf_object__add_programs /src/libbpf/src/libbpf.c:928 #3 0x00000040df3e in bpf_object__elf_collect /src/libbpf/src/libbpf.c:3930 #4 0x00000040df3e in bpf_object_open /src/libbpf/src/libbpf.c:8067 #5 0x00000040f176 in bpf_object__open_file /src/libbpf/src/libbpf.c:8090 #6 0x000000400c16 in main /poc/poc.c:8 #7 0x7fc3043d25b4 in __libc_start_call_main (/lib64/libc.so.6+0x35b4) #8 0x7fc3043d2667 in __libc_start_main@@GLIBC_2.34 (/lib64/libc.so.6+0x3667) #9 0x000000400b34 in _start (/poc/poc+0x400b34) 0x7c7302fe0000 is located 64 bytes before 104-byte region [0x7c7302fe0040,0x7c7302fe00a8) allocated by thread T0 here: #0 0x7fc3046e716b in malloc (/lib64/libasan.so.8+0xe716b) #1 0x7fc3045ee600 in __libelf_set_rawdata_wrlock (/lib64/libelf.so.1+0xb600) #2 0x7fc3045ef018 in __elf_getdata_rdlock (/lib64/libelf.so.1+0xc018) #3 0x00000040642f in elf_sec_data /src/libbpf/src/libbpf.c:3740 The problem here is that currently, libbpf only checks that the program end is within the section bounds. There used to be a check `while (sec_off < sec_sz)` in bpf_object__add_programs, however, it was removed by commit 6245947 ("libbpf: Allow gaps in BPF program sections to support overriden weak functions"). Add a check for detecting the overflow of `sec_off + prog_sz` to bpf_object__init_prog to fix this issue. [1] https://github.com/lmarch2/poc/blob/main/libbpf/libbpf.md Fixes: 6245947 ("libbpf: Allow gaps in BPF program sections to support overriden weak functions") Reported-by: lmarch2 <2524158037@qq.com> Signed-off-by: Viktor Malik <vmalik@redhat.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Reviewed-by: Shung-Hsi Yu <shung-hsi.yu@suse.com> Link: https://github.com/lmarch2/poc/blob/main/libbpf/libbpf.md Link: https://lore.kernel.org/bpf/20250415155014.397603-1-vmalik@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 59d9094 upstream. The folio refcount may be increased unexpectly through try_get_folio() by caller such as split_huge_pages. In huge_pmd_unshare(), we use refcount to check whether a pmd page table is shared. The check is incorrect if the refcount is increased by the above caller, and this can cause the page table leaked: BUG: Bad page state in process sh pfn:109324 page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x66 pfn:0x109324 flags: 0x17ffff800000000(node=0|zone=2|lastcpupid=0xfffff) page_type: f2(table) raw: 017ffff800000000 0000000000000000 0000000000000000 0000000000000000 raw: 0000000000000066 0000000000000000 00000000f2000000 0000000000000000 page dumped because: nonzero mapcount ... CPU: 31 UID: 0 PID: 7515 Comm: sh Kdump: loaded Tainted: G B 6.13.0-rc2master+ #7 Tainted: [B]=BAD_PAGE Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 Call trace: show_stack+0x20/0x38 (C) dump_stack_lvl+0x80/0xf8 dump_stack+0x18/0x28 bad_page+0x8c/0x130 free_page_is_bad_report+0xa4/0xb0 free_unref_page+0x3cc/0x620 __folio_put+0xf4/0x158 split_huge_pages_all+0x1e0/0x3e8 split_huge_pages_write+0x25c/0x2d8 full_proxy_write+0x64/0xd8 vfs_write+0xcc/0x280 ksys_write+0x70/0x110 __arm64_sys_write+0x24/0x38 invoke_syscall+0x50/0x120 el0_svc_common.constprop.0+0xc8/0xf0 do_el0_svc+0x24/0x38 el0_svc+0x34/0x128 el0t_64_sync_handler+0xc8/0xd0 el0t_64_sync+0x190/0x198 The issue may be triggered by damon, offline_page, page_idle, etc, which will increase the refcount of page table. 1. The page table itself will be discarded after reporting the "nonzero mapcount". 2. The HugeTLB page mapped by the page table miss freeing since we treat the page table as shared and a shared page table will not be unmapped. Fix it by introducing independent PMD page table shared count. As described by comment, pt_index/pt_mm/pt_frag_refcount are used for s390 gmap, x86 pgds and powerpc, pt_share_count is used for x86/arm64/riscv pmds, so we can reuse the field as pt_share_count. Link: https://lkml.kernel.org/r/20241216071147.3984217-1-liushixin2@huawei.com Fixes: 39dde65 ("[PATCH] shared page table for hugetlb page") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Ken Chen <kenneth.w.chen@intel.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nanyong Sun <sunnanyong@huawei.com> Cc: Jane Chu <jane.chu@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> [backport note: struct ptdesc did not exist yet, stuff it equivalently into struct page instead] Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2d72afb ] A crash in conntrack was reported while trying to unlink the conntrack entry from the hash bucket list: [exception RIP: __nf_ct_delete_from_lists+172] [..] #7 [ff539b5a2b043aa0] nf_ct_delete at ffffffffc124d421 [nf_conntrack] #8 [ff539b5a2b043ad0] nf_ct_gc_expired at ffffffffc124d999 [nf_conntrack] #9 [ff539b5a2b043ae0] __nf_conntrack_find_get at ffffffffc124efbc [nf_conntrack] [..] The nf_conn struct is marked as allocated from slab but appears to be in a partially initialised state: ct hlist pointer is garbage; looks like the ct hash value (hence crash). ct->status is equal to IPS_CONFIRMED|IPS_DYING, which is expected ct->timeout is 30000 (=30s), which is unexpected. Everything else looks like normal udp conntrack entry. If we ignore ct->status and pretend its 0, the entry matches those that are newly allocated but not yet inserted into the hash: - ct hlist pointers are overloaded and store/cache the raw tuple hash - ct->timeout matches the relative time expected for a new udp flow rather than the absolute 'jiffies' value. If it were not for the presence of IPS_CONFIRMED, __nf_conntrack_find_get() would have skipped the entry. Theory is that we did hit following race: cpu x cpu y cpu z found entry E found entry E E is expired <preemption> nf_ct_delete() return E to rcu slab init_conntrack E is re-inited, ct->status set to 0 reply tuplehash hnnode.pprev stores hash value. cpu y found E right before it was deleted on cpu x. E is now re-inited on cpu z. cpu y was preempted before checking for expiry and/or confirm bit. ->refcnt set to 1 E now owned by skb ->timeout set to 30000 If cpu y were to resume now, it would observe E as expired but would skip E due to missing CONFIRMED bit. nf_conntrack_confirm gets called sets: ct->status |= CONFIRMED This is wrong: E is not yet added to hashtable. cpu y resumes, it observes E as expired but CONFIRMED: <resumes> nf_ct_expired() -> yes (ct->timeout is 30s) confirmed bit set. cpu y will try to delete E from the hashtable: nf_ct_delete() -> set DYING bit __nf_ct_delete_from_lists Even this scenario doesn't guarantee a crash: cpu z still holds the table bucket lock(s) so y blocks: wait for spinlock held by z CONFIRMED is set but there is no guarantee ct will be added to hash: "chaintoolong" or "clash resolution" logic both skip the insert step. reply hnnode.pprev still stores the hash value. unlocks spinlock return NF_DROP <unblocks, then crashes on hlist_nulls_del_rcu pprev> In case CPU z does insert the entry into the hashtable, cpu y will unlink E again right away but no crash occurs. Without 'cpu y' race, 'garbage' hlist is of no consequence: ct refcnt remains at 1, eventually skb will be free'd and E gets destroyed via: nf_conntrack_put -> nf_conntrack_destroy -> nf_ct_destroy. To resolve this, move the IPS_CONFIRMED assignment after the table insertion but before the unlock. Pablo points out that the confirm-bit-store could be reordered to happen before hlist add resp. the timeout fixup, so switch to set_bit and before_atomic memory barrier to prevent this. It doesn't matter if other CPUs can observe a newly inserted entry right before the CONFIRMED bit was set: Such event cannot be distinguished from above "E is the old incarnation" case: the entry will be skipped. Also change nf_ct_should_gc() to first check the confirmed bit. The gc sequence is: 1. Check if entry has expired, if not skip to next entry 2. Obtain a reference to the expired entry. 3. Call nf_ct_should_gc() to double-check step 1. nf_ct_should_gc() is thus called only for entries that already failed an expiry check. After this patch, once the confirmed bit check passes ct->timeout has been altered to reflect the absolute 'best before' date instead of a relative time. Step 3 will therefore not remove the entry. Without this change to nf_ct_should_gc() we could still get this sequence: 1. Check if entry has expired. 2. Obtain a reference. 3. Call nf_ct_should_gc() to double-check step 1: 4 - entry is still observed as expired 5 - meanwhile, ct->timeout is corrected to absolute value on other CPU and confirm bit gets set 6 - confirm bit is seen 7 - valid entry is removed again First do check 6), then 4) so the gc expiry check always picks up either confirmed bit unset (entry gets skipped) or expiry re-check failure for re-inited conntrack objects. This change cannot be backported to releases before 5.19. Without commit 8a75a2c ("netfilter: conntrack: remove unconfirmed list") |= IPS_CONFIRMED line cannot be moved without further changes. Cc: Razvan Cojocaru <rzvncj@gmail.com> Link: https://lore.kernel.org/netfilter-devel/20250627142758.25664-1-fw@strlen.de/ Link: https://lore.kernel.org/netfilter-devel/4239da15-83ff-4ca4-939d-faef283471bb@gmail.com/ Fixes: 1397af5 ("netfilter: conntrack: remove the percpu dying list") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a509a55 ] As syzbot [1] reported as below: R10: 0000000000000100 R11: 0000000000000206 R12: 00007ffe17473450 R13: 00007f28b1c10854 R14: 000000000000dae5 R15: 00007ffe17474520 </TASK> ---[ end trace 0000000000000000 ]--- ================================================================== BUG: KASAN: use-after-free in __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 Read of size 8 at addr ffff88812d962278 by task syz-executor/564 CPU: 1 PID: 564 Comm: syz-executor Tainted: G W 6.1.129-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Call Trace: <TASK> __dump_stack+0x21/0x24 lib/dump_stack.c:88 dump_stack_lvl+0xee/0x158 lib/dump_stack.c:106 print_address_description+0x71/0x210 mm/kasan/report.c:316 print_report+0x4a/0x60 mm/kasan/report.c:427 kasan_report+0x122/0x150 mm/kasan/report.c:531 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report_generic.c:351 __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 __list_del_entry include/linux/list.h:134 [inline] list_del_init include/linux/list.h:206 [inline] f2fs_inode_synced+0xf7/0x2e0 fs/f2fs/super.c:1531 f2fs_update_inode+0x74/0x1c40 fs/f2fs/inode.c:585 f2fs_update_inode_page+0x137/0x170 fs/f2fs/inode.c:703 f2fs_write_inode+0x4ec/0x770 fs/f2fs/inode.c:731 write_inode fs/fs-writeback.c:1460 [inline] __writeback_single_inode+0x4a0/0xab0 fs/fs-writeback.c:1677 writeback_single_inode+0x221/0x8b0 fs/fs-writeback.c:1733 sync_inode_metadata+0xb6/0x110 fs/fs-writeback.c:2789 f2fs_sync_inode_meta+0x16d/0x2a0 fs/f2fs/checkpoint.c:1159 block_operations fs/f2fs/checkpoint.c:1269 [inline] f2fs_write_checkpoint+0xca3/0x2100 fs/f2fs/checkpoint.c:1658 kill_f2fs_super+0x231/0x390 fs/f2fs/super.c:4668 deactivate_locked_super+0x98/0x100 fs/super.c:332 deactivate_super+0xaf/0xe0 fs/super.c:363 cleanup_mnt+0x45f/0x4e0 fs/namespace.c:1186 __cleanup_mnt+0x19/0x20 fs/namespace.c:1193 task_work_run+0x1c6/0x230 kernel/task_work.c:203 exit_task_work include/linux/task_work.h:39 [inline] do_exit+0x9fb/0x2410 kernel/exit.c:871 do_group_exit+0x210/0x2d0 kernel/exit.c:1021 __do_sys_exit_group kernel/exit.c:1032 [inline] __se_sys_exit_group kernel/exit.c:1030 [inline] __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1030 x64_sys_call+0x7b4/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:232 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 RIP: 0033:0x7f28b1b8e169 Code: Unable to access opcode bytes at 0x7f28b1b8e13f. RSP: 002b:00007ffe174710a8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 00007f28b1c10879 RCX: 00007f28b1b8e169 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000001 RBP: 0000000000000002 R08: 00007ffe1746ee47 R09: 00007ffe17472360 R10: 0000000000000009 R11: 0000000000000246 R12: 00007ffe17472360 R13: 00007f28b1c10854 R14: 000000000000dae5 R15: 00007ffe17474520 </TASK> Allocated by task 569: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_alloc_info+0x25/0x30 mm/kasan/generic.c:505 __kasan_slab_alloc+0x72/0x80 mm/kasan/common.c:328 kasan_slab_alloc include/linux/kasan.h:201 [inline] slab_post_alloc_hook+0x4f/0x2c0 mm/slab.h:737 slab_alloc_node mm/slub.c:3398 [inline] slab_alloc mm/slub.c:3406 [inline] __kmem_cache_alloc_lru mm/slub.c:3413 [inline] kmem_cache_alloc_lru+0x104/0x220 mm/slub.c:3429 alloc_inode_sb include/linux/fs.h:3245 [inline] f2fs_alloc_inode+0x2d/0x340 fs/f2fs/super.c:1419 alloc_inode fs/inode.c:261 [inline] iget_locked+0x186/0x880 fs/inode.c:1373 f2fs_iget+0x55/0x4c60 fs/f2fs/inode.c:483 f2fs_lookup+0x366/0xab0 fs/f2fs/namei.c:487 __lookup_slow+0x2a3/0x3d0 fs/namei.c:1690 lookup_slow+0x57/0x70 fs/namei.c:1707 walk_component+0x2e6/0x410 fs/namei.c:1998 lookup_last fs/namei.c:2455 [inline] path_lookupat+0x180/0x490 fs/namei.c:2479 filename_lookup+0x1f0/0x500 fs/namei.c:2508 vfs_statx+0x10b/0x660 fs/stat.c:229 vfs_fstatat fs/stat.c:267 [inline] vfs_lstat include/linux/fs.h:3424 [inline] __do_sys_newlstat fs/stat.c:423 [inline] __se_sys_newlstat+0xd5/0x350 fs/stat.c:417 __x64_sys_newlstat+0x5b/0x70 fs/stat.c:417 x64_sys_call+0x393/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:7 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 Freed by task 13: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_free_info+0x31/0x50 mm/kasan/generic.c:516 ____kasan_slab_free+0x132/0x180 mm/kasan/common.c:236 __kasan_slab_free+0x11/0x20 mm/kasan/common.c:244 kasan_slab_free include/linux/kasan.h:177 [inline] slab_free_hook mm/slub.c:1724 [inline] slab_free_freelist_hook+0xc2/0x190 mm/slub.c:1750 slab_free mm/slub.c:3661 [inline] kmem_cache_free+0x12d/0x2a0 mm/slub.c:3683 f2fs_free_inode+0x24/0x30 fs/f2fs/super.c:1562 i_callback+0x4c/0x70 fs/inode.c:250 rcu_do_batch+0x503/0xb80 kernel/rcu/tree.c:2297 rcu_core+0x5a2/0xe70 kernel/rcu/tree.c:2557 rcu_core_si+0x9/0x10 kernel/rcu/tree.c:2574 handle_softirqs+0x178/0x500 kernel/softirq.c:578 run_ksoftirqd+0x28/0x30 kernel/softirq.c:945 smpboot_thread_fn+0x45a/0x8c0 kernel/smpboot.c:164 kthread+0x270/0x310 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 Last potentially related work creation: kasan_save_stack+0x3a/0x60 mm/kasan/common.c:45 __kasan_record_aux_stack+0xb6/0xc0 mm/kasan/generic.c:486 kasan_record_aux_stack_noalloc+0xb/0x10 mm/kasan/generic.c:496 call_rcu+0xd4/0xf70 kernel/rcu/tree.c:2845 destroy_inode fs/inode.c:316 [inline] evict+0x7da/0x870 fs/inode.c:720 iput_final fs/inode.c:1834 [inline] iput+0x62b/0x830 fs/inode.c:1860 do_unlinkat+0x356/0x540 fs/namei.c:4397 __do_sys_unlink fs/namei.c:4438 [inline] __se_sys_unlink fs/namei.c:4436 [inline] __x64_sys_unlink+0x49/0x50 fs/namei.c:4436 x64_sys_call+0x958/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:88 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 The buggy address belongs to the object at ffff88812d961f20 which belongs to the cache f2fs_inode_cache of size 1200 The buggy address is located 856 bytes inside of 1200-byte region [ffff88812d961f20, ffff88812d9623d0) The buggy address belongs to the physical page: page:ffffea0004b65800 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x12d960 head:ffffea0004b65800 order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=1) raw: 4000000000010200 0000000000000000 dead000000000122 ffff88810a94c500 raw: 0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected page_owner tracks the page as allocated page last allocated via order 2, migratetype Reclaimable, gfp_mask 0x1d2050(__GFP_IO|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC|__GFP_HARDWALL|__GFP_RECLAIMABLE), pid 569, tgid 568 (syz.2.16), ts 55943246141, free_ts 0 set_page_owner include/linux/page_owner.h:31 [inline] post_alloc_hook+0x1d0/0x1f0 mm/page_alloc.c:2532 prep_new_page mm/page_alloc.c:2539 [inline] get_page_from_freelist+0x2e63/0x2ef0 mm/page_alloc.c:4328 __alloc_pages+0x235/0x4b0 mm/page_alloc.c:5605 alloc_slab_page include/linux/gfp.h:-1 [inline] allocate_slab mm/slub.c:1939 [inline] new_slab+0xec/0x4b0 mm/slub.c:1992 ___slab_alloc+0x6f6/0xb50 mm/slub.c:3180 __slab_alloc+0x5e/0xa0 mm/slub.c:3279 slab_alloc_node mm/slub.c:3364 [inline] slab_alloc mm/slub.c:3406 [inline] __kmem_cache_alloc_lru mm/slub.c:3413 [inline] kmem_cache_alloc_lru+0x13f/0x220 mm/slub.c:3429 alloc_inode_sb include/linux/fs.h:3245 [inline] f2fs_alloc_inode+0x2d/0x340 fs/f2fs/super.c:1419 alloc_inode fs/inode.c:261 [inline] iget_locked+0x186/0x880 fs/inode.c:1373 f2fs_iget+0x55/0x4c60 fs/f2fs/inode.c:483 f2fs_fill_super+0x3ad7/0x6bb0 fs/f2fs/super.c:4293 mount_bdev+0x2ae/0x3e0 fs/super.c:1443 f2fs_mount+0x34/0x40 fs/f2fs/super.c:4642 legacy_get_tree+0xea/0x190 fs/fs_context.c:632 vfs_get_tree+0x89/0x260 fs/super.c:1573 do_new_mount+0x25a/0xa20 fs/namespace.c:3056 page_owner free stack trace missing Memory state around the buggy address: ffff88812d962100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88812d962180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88812d962200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88812d962280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88812d962300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== [1] https://syzkaller.appspot.com/x/report.txt?x=13448368580000 This bug can be reproduced w/ the reproducer [2], once we enable CONFIG_F2FS_CHECK_FS config, the reproducer will trigger panic as below, so the direct reason of this bug is the same as the one below patch [3] fixed. kernel BUG at fs/f2fs/inode.c:857! RIP: 0010:f2fs_evict_inode+0x1204/0x1a20 Call Trace: <TASK> evict+0x32a/0x7a0 do_unlinkat+0x37b/0x5b0 __x64_sys_unlink+0xad/0x100 do_syscall_64+0x5a/0xb0 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 RIP: 0010:f2fs_evict_inode+0x1204/0x1a20 [2] https://syzkaller.appspot.com/x/repro.c?x=17495ccc580000 [3] https://lore.kernel.org/linux-f2fs-devel/20250702120321.1080759-1-chao@kernel.org Tracepoints before panic: f2fs_unlink_enter: dev = (7,0), dir ino = 3, i_size = 4096, i_blocks = 8, name = file1 f2fs_unlink_exit: dev = (7,0), ino = 7, ret = 0 f2fs_evict_inode: dev = (7,0), ino = 7, pino = 3, i_mode = 0x81ed, i_size = 10, i_nlink = 0, i_blocks = 0, i_advise = 0x0 f2fs_truncate_node: dev = (7,0), ino = 7, nid = 8, block_address = 0x3c05 f2fs_unlink_enter: dev = (7,0), dir ino = 3, i_size = 4096, i_blocks = 8, name = file3 f2fs_unlink_exit: dev = (7,0), ino = 8, ret = 0 f2fs_evict_inode: dev = (7,0), ino = 8, pino = 3, i_mode = 0x81ed, i_size = 9000, i_nlink = 0, i_blocks = 24, i_advise = 0x4 f2fs_truncate: dev = (7,0), ino = 8, pino = 3, i_mode = 0x81ed, i_size = 0, i_nlink = 0, i_blocks = 24, i_advise = 0x4 f2fs_truncate_blocks_enter: dev = (7,0), ino = 8, i_size = 0, i_blocks = 24, start file offset = 0 f2fs_truncate_blocks_exit: dev = (7,0), ino = 8, ret = -2 The root cause is: in the fuzzed image, dnode #8 belongs to inode #7, after inode #7 eviction, dnode #8 was dropped. However there is dirent that has ino #8, so, once we unlink file3, in f2fs_evict_inode(), both f2fs_truncate() and f2fs_update_inode_page() will fail due to we can not load node #8, result in we missed to call f2fs_inode_synced() to clear inode dirty status. Let's fix this by calling f2fs_inode_synced() in error path of f2fs_evict_inode(). PS: As I verified, the reproducer [2] can trigger this bug in v6.1.129, but it failed in v6.16-rc4, this is because the testcase will stop due to other corruption has been detected by f2fs: F2FS-fs (loop0): inconsistent node block, node_type:2, nid:8, node_footer[nid:8,ino:8,ofs:0,cpver:5013063228981249506,blkaddr:15366] F2FS-fs (loop0): f2fs_lookup: inode (ino=9) has zero i_nlink Fixes: 0f18b46 ("f2fs: flush inode metadata when checkpoint is doing") Closes: https://syzkaller.appspot.com/x/report.txt?x=13448368580000 Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c80aa2a ] The hfsplus_bnode_read() method can trigger the issue: [ 174.852007][ T9784] ================================================================== [ 174.852709][ T9784] BUG: KASAN: slab-out-of-bounds in hfsplus_bnode_read+0x2f4/0x360 [ 174.853412][ T9784] Read of size 8 at addr ffff88810b5fc6c0 by task repro/9784 [ 174.854059][ T9784] [ 174.854272][ T9784] CPU: 1 UID: 0 PID: 9784 Comm: repro Not tainted 6.16.0-rc3 #7 PREEMPT(full) [ 174.854281][ T9784] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 174.854286][ T9784] Call Trace: [ 174.854289][ T9784] <TASK> [ 174.854292][ T9784] dump_stack_lvl+0x10e/0x1f0 [ 174.854305][ T9784] print_report+0xd0/0x660 [ 174.854315][ T9784] ? __virt_addr_valid+0x81/0x610 [ 174.854323][ T9784] ? __phys_addr+0xe8/0x180 [ 174.854330][ T9784] ? hfsplus_bnode_read+0x2f4/0x360 [ 174.854337][ T9784] kasan_report+0xc6/0x100 [ 174.854346][ T9784] ? hfsplus_bnode_read+0x2f4/0x360 [ 174.854354][ T9784] hfsplus_bnode_read+0x2f4/0x360 [ 174.854362][ T9784] hfsplus_bnode_dump+0x2ec/0x380 [ 174.854370][ T9784] ? __pfx_hfsplus_bnode_dump+0x10/0x10 [ 174.854377][ T9784] ? hfsplus_bnode_write_u16+0x83/0xb0 [ 174.854385][ T9784] ? srcu_gp_start+0xd0/0x310 [ 174.854393][ T9784] ? __mark_inode_dirty+0x29e/0xe40 [ 174.854402][ T9784] hfsplus_brec_remove+0x3d2/0x4e0 [ 174.854411][ T9784] __hfsplus_delete_attr+0x290/0x3a0 [ 174.854419][ T9784] ? __pfx_hfs_find_1st_rec_by_cnid+0x10/0x10 [ 174.854427][ T9784] ? __pfx___hfsplus_delete_attr+0x10/0x10 [ 174.854436][ T9784] ? __asan_memset+0x23/0x50 [ 174.854450][ T9784] hfsplus_delete_all_attrs+0x262/0x320 [ 174.854459][ T9784] ? __pfx_hfsplus_delete_all_attrs+0x10/0x10 [ 174.854469][ T9784] ? rcu_is_watching+0x12/0xc0 [ 174.854476][ T9784] ? __mark_inode_dirty+0x29e/0xe40 [ 174.854483][ T9784] hfsplus_delete_cat+0x845/0xde0 [ 174.854493][ T9784] ? __pfx_hfsplus_delete_cat+0x10/0x10 [ 174.854507][ T9784] hfsplus_unlink+0x1ca/0x7c0 [ 174.854516][ T9784] ? __pfx_hfsplus_unlink+0x10/0x10 [ 174.854525][ T9784] ? down_write+0x148/0x200 [ 174.854532][ T9784] ? __pfx_down_write+0x10/0x10 [ 174.854540][ T9784] vfs_unlink+0x2fe/0x9b0 [ 174.854549][ T9784] do_unlinkat+0x490/0x670 [ 174.854557][ T9784] ? __pfx_do_unlinkat+0x10/0x10 [ 174.854565][ T9784] ? __might_fault+0xbc/0x130 [ 174.854576][ T9784] ? getname_flags.part.0+0x1c5/0x550 [ 174.854584][ T9784] __x64_sys_unlink+0xc5/0x110 [ 174.854592][ T9784] do_syscall_64+0xc9/0x480 [ 174.854600][ T9784] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 174.854608][ T9784] RIP: 0033:0x7f6fdf4c3167 [ 174.854614][ T9784] Code: f0 ff ff 73 01 c3 48 8b 0d 26 0d 0e 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 08 [ 174.854622][ T9784] RSP: 002b:00007ffcb948bca8 EFLAGS: 00000206 ORIG_RAX: 0000000000000057 [ 174.854630][ T9784] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f6fdf4c3167 [ 174.854636][ T9784] RDX: 00007ffcb948bcc0 RSI: 00007ffcb948bcc0 RDI: 00007ffcb948bd50 [ 174.854641][ T9784] RBP: 00007ffcb948cd90 R08: 0000000000000001 R09: 00007ffcb948bb40 [ 174.854645][ T9784] R10: 00007f6fdf564fc0 R11: 0000000000000206 R12: 0000561e1bc9c2d0 [ 174.854650][ T9784] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 174.854658][ T9784] </TASK> [ 174.854661][ T9784] [ 174.879281][ T9784] Allocated by task 9784: [ 174.879664][ T9784] kasan_save_stack+0x20/0x40 [ 174.880082][ T9784] kasan_save_track+0x14/0x30 [ 174.880500][ T9784] __kasan_kmalloc+0xaa/0xb0 [ 174.880908][ T9784] __kmalloc_noprof+0x205/0x550 [ 174.881337][ T9784] __hfs_bnode_create+0x107/0x890 [ 174.881779][ T9784] hfsplus_bnode_find+0x2d0/0xd10 [ 174.882222][ T9784] hfsplus_brec_find+0x2b0/0x520 [ 174.882659][ T9784] hfsplus_delete_all_attrs+0x23b/0x320 [ 174.883144][ T9784] hfsplus_delete_cat+0x845/0xde0 [ 174.883595][ T9784] hfsplus_rmdir+0x106/0x1b0 [ 174.884004][ T9784] vfs_rmdir+0x206/0x690 [ 174.884379][ T9784] do_rmdir+0x2b7/0x390 [ 174.884751][ T9784] __x64_sys_rmdir+0xc5/0x110 [ 174.885167][ T9784] do_syscall_64+0xc9/0x480 [ 174.885568][ T9784] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 174.886083][ T9784] [ 174.886293][ T9784] The buggy address belongs to the object at ffff88810b5fc600 [ 174.886293][ T9784] which belongs to the cache kmalloc-192 of size 192 [ 174.887507][ T9784] The buggy address is located 40 bytes to the right of [ 174.887507][ T9784] allocated 152-byte region [ffff88810b5fc600, ffff88810b5fc698) [ 174.888766][ T9784] [ 174.888976][ T9784] The buggy address belongs to the physical page: [ 174.889533][ T9784] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x10b5fc [ 174.890295][ T9784] flags: 0x57ff00000000000(node=1|zone=2|lastcpupid=0x7ff) [ 174.890927][ T9784] page_type: f5(slab) [ 174.891284][ T9784] raw: 057ff00000000000 ffff88801b4423c0 ffffea000426dc80 dead000000000002 [ 174.892032][ T9784] raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000 [ 174.892774][ T9784] page dumped because: kasan: bad access detected [ 174.893327][ T9784] page_owner tracks the page as allocated [ 174.893825][ T9784] page last allocated via order 0, migratetype Unmovable, gfp_mask 0x52c00(GFP_NOIO|__GFP_NOWARN|__GFP_NO1 [ 174.895373][ T9784] post_alloc_hook+0x1c0/0x230 [ 174.895801][ T9784] get_page_from_freelist+0xdeb/0x3b30 [ 174.896284][ T9784] __alloc_frozen_pages_noprof+0x25c/0x2460 [ 174.896810][ T9784] alloc_pages_mpol+0x1fb/0x550 [ 174.897242][ T9784] new_slab+0x23b/0x340 [ 174.897614][ T9784] ___slab_alloc+0xd81/0x1960 [ 174.898028][ T9784] __slab_alloc.isra.0+0x56/0xb0 [ 174.898468][ T9784] __kmalloc_noprof+0x2b0/0x550 [ 174.898896][ T9784] usb_alloc_urb+0x73/0xa0 [ 174.899289][ T9784] usb_control_msg+0x1cb/0x4a0 [ 174.899718][ T9784] usb_get_string+0xab/0x1a0 [ 174.900133][ T9784] usb_string_sub+0x107/0x3c0 [ 174.900549][ T9784] usb_string+0x307/0x670 [ 174.900933][ T9784] usb_cache_string+0x80/0x150 [ 174.901355][ T9784] usb_new_device+0x1d0/0x19d0 [ 174.901786][ T9784] register_root_hub+0x299/0x730 [ 174.902231][ T9784] page last free pid 10 tgid 10 stack trace: [ 174.902757][ T9784] __free_frozen_pages+0x80c/0x1250 [ 174.903217][ T9784] vfree.part.0+0x12b/0xab0 [ 174.903645][ T9784] delayed_vfree_work+0x93/0xd0 [ 174.904073][ T9784] process_one_work+0x9b5/0x1b80 [ 174.904519][ T9784] worker_thread+0x630/0xe60 [ 174.904927][ T9784] kthread+0x3a8/0x770 [ 174.905291][ T9784] ret_from_fork+0x517/0x6e0 [ 174.905709][ T9784] ret_from_fork_asm+0x1a/0x30 [ 174.906128][ T9784] [ 174.906338][ T9784] Memory state around the buggy address: [ 174.906828][ T9784] ffff88810b5fc580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc [ 174.907528][ T9784] ffff88810b5fc600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 174.908222][ T9784] >ffff88810b5fc680: 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc [ 174.908917][ T9784] ^ [ 174.909481][ T9784] ffff88810b5fc700: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 174.910432][ T9784] ffff88810b5fc780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc [ 174.911401][ T9784] ================================================================== The reason of the issue that code doesn't check the correctness of the requested offset and length. As a result, incorrect value of offset or/and length could result in access out of allocated memory. This patch introduces is_bnode_offset_valid() method that checks the requested offset value. Also, it introduces check_and_correct_requested_length() method that checks and correct the requested length (if it is necessary). These methods are used in hfsplus_bnode_read(), hfsplus_bnode_write(), hfsplus_bnode_clear(), hfsplus_bnode_copy(), and hfsplus_bnode_move() with the goal to prevent the access out of allocated memory and triggering the crash. Reported-by: Kun Hu <huk23@m.fudan.edu.cn> Reported-by: Jiaji Qin <jjtan24@m.fudan.edu.cn> Reported-by: Shuoran Bai <baishuoran@hrbeu.edu.cn> Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Link: https://lore.kernel.org/r/20250703214804.244077-1-slava@dubeyko.com Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a509a55 ] As syzbot [1] reported as below: R10: 0000000000000100 R11: 0000000000000206 R12: 00007ffe17473450 R13: 00007f28b1c10854 R14: 000000000000dae5 R15: 00007ffe17474520 </TASK> ---[ end trace 0000000000000000 ]--- ================================================================== BUG: KASAN: use-after-free in __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 Read of size 8 at addr ffff88812d962278 by task syz-executor/564 CPU: 1 PID: 564 Comm: syz-executor Tainted: G W 6.1.129-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/12/2025 Call Trace: <TASK> __dump_stack+0x21/0x24 lib/dump_stack.c:88 dump_stack_lvl+0xee/0x158 lib/dump_stack.c:106 print_address_description+0x71/0x210 mm/kasan/report.c:316 print_report+0x4a/0x60 mm/kasan/report.c:427 kasan_report+0x122/0x150 mm/kasan/report.c:531 __asan_report_load8_noabort+0x14/0x20 mm/kasan/report_generic.c:351 __list_del_entry_valid+0xa6/0x130 lib/list_debug.c:62 __list_del_entry include/linux/list.h:134 [inline] list_del_init include/linux/list.h:206 [inline] f2fs_inode_synced+0xf7/0x2e0 fs/f2fs/super.c:1531 f2fs_update_inode+0x74/0x1c40 fs/f2fs/inode.c:585 f2fs_update_inode_page+0x137/0x170 fs/f2fs/inode.c:703 f2fs_write_inode+0x4ec/0x770 fs/f2fs/inode.c:731 write_inode fs/fs-writeback.c:1460 [inline] __writeback_single_inode+0x4a0/0xab0 fs/fs-writeback.c:1677 writeback_single_inode+0x221/0x8b0 fs/fs-writeback.c:1733 sync_inode_metadata+0xb6/0x110 fs/fs-writeback.c:2789 f2fs_sync_inode_meta+0x16d/0x2a0 fs/f2fs/checkpoint.c:1159 block_operations fs/f2fs/checkpoint.c:1269 [inline] f2fs_write_checkpoint+0xca3/0x2100 fs/f2fs/checkpoint.c:1658 kill_f2fs_super+0x231/0x390 fs/f2fs/super.c:4668 deactivate_locked_super+0x98/0x100 fs/super.c:332 deactivate_super+0xaf/0xe0 fs/super.c:363 cleanup_mnt+0x45f/0x4e0 fs/namespace.c:1186 __cleanup_mnt+0x19/0x20 fs/namespace.c:1193 task_work_run+0x1c6/0x230 kernel/task_work.c:203 exit_task_work include/linux/task_work.h:39 [inline] do_exit+0x9fb/0x2410 kernel/exit.c:871 do_group_exit+0x210/0x2d0 kernel/exit.c:1021 __do_sys_exit_group kernel/exit.c:1032 [inline] __se_sys_exit_group kernel/exit.c:1030 [inline] __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1030 x64_sys_call+0x7b4/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:232 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 RIP: 0033:0x7f28b1b8e169 Code: Unable to access opcode bytes at 0x7f28b1b8e13f. RSP: 002b:00007ffe174710a8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7 RAX: ffffffffffffffda RBX: 00007f28b1c10879 RCX: 00007f28b1b8e169 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000001 RBP: 0000000000000002 R08: 00007ffe1746ee47 R09: 00007ffe17472360 R10: 0000000000000009 R11: 0000000000000246 R12: 00007ffe17472360 R13: 00007f28b1c10854 R14: 000000000000dae5 R15: 00007ffe17474520 </TASK> Allocated by task 569: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_alloc_info+0x25/0x30 mm/kasan/generic.c:505 __kasan_slab_alloc+0x72/0x80 mm/kasan/common.c:328 kasan_slab_alloc include/linux/kasan.h:201 [inline] slab_post_alloc_hook+0x4f/0x2c0 mm/slab.h:737 slab_alloc_node mm/slub.c:3398 [inline] slab_alloc mm/slub.c:3406 [inline] __kmem_cache_alloc_lru mm/slub.c:3413 [inline] kmem_cache_alloc_lru+0x104/0x220 mm/slub.c:3429 alloc_inode_sb include/linux/fs.h:3245 [inline] f2fs_alloc_inode+0x2d/0x340 fs/f2fs/super.c:1419 alloc_inode fs/inode.c:261 [inline] iget_locked+0x186/0x880 fs/inode.c:1373 f2fs_iget+0x55/0x4c60 fs/f2fs/inode.c:483 f2fs_lookup+0x366/0xab0 fs/f2fs/namei.c:487 __lookup_slow+0x2a3/0x3d0 fs/namei.c:1690 lookup_slow+0x57/0x70 fs/namei.c:1707 walk_component+0x2e6/0x410 fs/namei.c:1998 lookup_last fs/namei.c:2455 [inline] path_lookupat+0x180/0x490 fs/namei.c:2479 filename_lookup+0x1f0/0x500 fs/namei.c:2508 vfs_statx+0x10b/0x660 fs/stat.c:229 vfs_fstatat fs/stat.c:267 [inline] vfs_lstat include/linux/fs.h:3424 [inline] __do_sys_newlstat fs/stat.c:423 [inline] __se_sys_newlstat+0xd5/0x350 fs/stat.c:417 __x64_sys_newlstat+0x5b/0x70 fs/stat.c:417 x64_sys_call+0x393/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:7 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 Freed by task 13: kasan_save_stack mm/kasan/common.c:45 [inline] kasan_set_track+0x4b/0x70 mm/kasan/common.c:52 kasan_save_free_info+0x31/0x50 mm/kasan/generic.c:516 ____kasan_slab_free+0x132/0x180 mm/kasan/common.c:236 __kasan_slab_free+0x11/0x20 mm/kasan/common.c:244 kasan_slab_free include/linux/kasan.h:177 [inline] slab_free_hook mm/slub.c:1724 [inline] slab_free_freelist_hook+0xc2/0x190 mm/slub.c:1750 slab_free mm/slub.c:3661 [inline] kmem_cache_free+0x12d/0x2a0 mm/slub.c:3683 f2fs_free_inode+0x24/0x30 fs/f2fs/super.c:1562 i_callback+0x4c/0x70 fs/inode.c:250 rcu_do_batch+0x503/0xb80 kernel/rcu/tree.c:2297 rcu_core+0x5a2/0xe70 kernel/rcu/tree.c:2557 rcu_core_si+0x9/0x10 kernel/rcu/tree.c:2574 handle_softirqs+0x178/0x500 kernel/softirq.c:578 run_ksoftirqd+0x28/0x30 kernel/softirq.c:945 smpboot_thread_fn+0x45a/0x8c0 kernel/smpboot.c:164 kthread+0x270/0x310 kernel/kthread.c:376 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 Last potentially related work creation: kasan_save_stack+0x3a/0x60 mm/kasan/common.c:45 __kasan_record_aux_stack+0xb6/0xc0 mm/kasan/generic.c:486 kasan_record_aux_stack_noalloc+0xb/0x10 mm/kasan/generic.c:496 call_rcu+0xd4/0xf70 kernel/rcu/tree.c:2845 destroy_inode fs/inode.c:316 [inline] evict+0x7da/0x870 fs/inode.c:720 iput_final fs/inode.c:1834 [inline] iput+0x62b/0x830 fs/inode.c:1860 do_unlinkat+0x356/0x540 fs/namei.c:4397 __do_sys_unlink fs/namei.c:4438 [inline] __se_sys_unlink fs/namei.c:4436 [inline] __x64_sys_unlink+0x49/0x50 fs/namei.c:4436 x64_sys_call+0x958/0x9a0 arch/x86/include/generated/asm/syscalls_64.h:88 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x4c/0xa0 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x68/0xd2 The buggy address belongs to the object at ffff88812d961f20 which belongs to the cache f2fs_inode_cache of size 1200 The buggy address is located 856 bytes inside of 1200-byte region [ffff88812d961f20, ffff88812d9623d0) The buggy address belongs to the physical page: page:ffffea0004b65800 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x12d960 head:ffffea0004b65800 order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=1) raw: 4000000000010200 0000000000000000 dead000000000122 ffff88810a94c500 raw: 0000000000000000 00000000800c000c 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected page_owner tracks the page as allocated page last allocated via order 2, migratetype Reclaimable, gfp_mask 0x1d2050(__GFP_IO|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC|__GFP_HARDWALL|__GFP_RECLAIMABLE), pid 569, tgid 568 (syz.2.16), ts 55943246141, free_ts 0 set_page_owner include/linux/page_owner.h:31 [inline] post_alloc_hook+0x1d0/0x1f0 mm/page_alloc.c:2532 prep_new_page mm/page_alloc.c:2539 [inline] get_page_from_freelist+0x2e63/0x2ef0 mm/page_alloc.c:4328 __alloc_pages+0x235/0x4b0 mm/page_alloc.c:5605 alloc_slab_page include/linux/gfp.h:-1 [inline] allocate_slab mm/slub.c:1939 [inline] new_slab+0xec/0x4b0 mm/slub.c:1992 ___slab_alloc+0x6f6/0xb50 mm/slub.c:3180 __slab_alloc+0x5e/0xa0 mm/slub.c:3279 slab_alloc_node mm/slub.c:3364 [inline] slab_alloc mm/slub.c:3406 [inline] __kmem_cache_alloc_lru mm/slub.c:3413 [inline] kmem_cache_alloc_lru+0x13f/0x220 mm/slub.c:3429 alloc_inode_sb include/linux/fs.h:3245 [inline] f2fs_alloc_inode+0x2d/0x340 fs/f2fs/super.c:1419 alloc_inode fs/inode.c:261 [inline] iget_locked+0x186/0x880 fs/inode.c:1373 f2fs_iget+0x55/0x4c60 fs/f2fs/inode.c:483 f2fs_fill_super+0x3ad7/0x6bb0 fs/f2fs/super.c:4293 mount_bdev+0x2ae/0x3e0 fs/super.c:1443 f2fs_mount+0x34/0x40 fs/f2fs/super.c:4642 legacy_get_tree+0xea/0x190 fs/fs_context.c:632 vfs_get_tree+0x89/0x260 fs/super.c:1573 do_new_mount+0x25a/0xa20 fs/namespace.c:3056 page_owner free stack trace missing Memory state around the buggy address: ffff88812d962100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88812d962180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff88812d962200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff88812d962280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88812d962300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ================================================================== [1] https://syzkaller.appspot.com/x/report.txt?x=13448368580000 This bug can be reproduced w/ the reproducer [2], once we enable CONFIG_F2FS_CHECK_FS config, the reproducer will trigger panic as below, so the direct reason of this bug is the same as the one below patch [3] fixed. kernel BUG at fs/f2fs/inode.c:857! RIP: 0010:f2fs_evict_inode+0x1204/0x1a20 Call Trace: <TASK> evict+0x32a/0x7a0 do_unlinkat+0x37b/0x5b0 __x64_sys_unlink+0xad/0x100 do_syscall_64+0x5a/0xb0 entry_SYSCALL_64_after_hwframe+0x6e/0xd8 RIP: 0010:f2fs_evict_inode+0x1204/0x1a20 [2] https://syzkaller.appspot.com/x/repro.c?x=17495ccc580000 [3] https://lore.kernel.org/linux-f2fs-devel/20250702120321.1080759-1-chao@kernel.org Tracepoints before panic: f2fs_unlink_enter: dev = (7,0), dir ino = 3, i_size = 4096, i_blocks = 8, name = file1 f2fs_unlink_exit: dev = (7,0), ino = 7, ret = 0 f2fs_evict_inode: dev = (7,0), ino = 7, pino = 3, i_mode = 0x81ed, i_size = 10, i_nlink = 0, i_blocks = 0, i_advise = 0x0 f2fs_truncate_node: dev = (7,0), ino = 7, nid = 8, block_address = 0x3c05 f2fs_unlink_enter: dev = (7,0), dir ino = 3, i_size = 4096, i_blocks = 8, name = file3 f2fs_unlink_exit: dev = (7,0), ino = 8, ret = 0 f2fs_evict_inode: dev = (7,0), ino = 8, pino = 3, i_mode = 0x81ed, i_size = 9000, i_nlink = 0, i_blocks = 24, i_advise = 0x4 f2fs_truncate: dev = (7,0), ino = 8, pino = 3, i_mode = 0x81ed, i_size = 0, i_nlink = 0, i_blocks = 24, i_advise = 0x4 f2fs_truncate_blocks_enter: dev = (7,0), ino = 8, i_size = 0, i_blocks = 24, start file offset = 0 f2fs_truncate_blocks_exit: dev = (7,0), ino = 8, ret = -2 The root cause is: in the fuzzed image, dnode #8 belongs to inode #7, after inode #7 eviction, dnode #8 was dropped. However there is dirent that has ino #8, so, once we unlink file3, in f2fs_evict_inode(), both f2fs_truncate() and f2fs_update_inode_page() will fail due to we can not load node #8, result in we missed to call f2fs_inode_synced() to clear inode dirty status. Let's fix this by calling f2fs_inode_synced() in error path of f2fs_evict_inode(). PS: As I verified, the reproducer [2] can trigger this bug in v6.1.129, but it failed in v6.16-rc4, this is because the testcase will stop due to other corruption has been detected by f2fs: F2FS-fs (loop0): inconsistent node block, node_type:2, nid:8, node_footer[nid:8,ino:8,ofs:0,cpver:5013063228981249506,blkaddr:15366] F2FS-fs (loop0): f2fs_lookup: inode (ino=9) has zero i_nlink Fixes: 0f18b46 ("f2fs: flush inode metadata when checkpoint is doing") Closes: https://syzkaller.appspot.com/x/report.txt?x=13448368580000 Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c80aa2a ] The hfsplus_bnode_read() method can trigger the issue: [ 174.852007][ T9784] ================================================================== [ 174.852709][ T9784] BUG: KASAN: slab-out-of-bounds in hfsplus_bnode_read+0x2f4/0x360 [ 174.853412][ T9784] Read of size 8 at addr ffff88810b5fc6c0 by task repro/9784 [ 174.854059][ T9784] [ 174.854272][ T9784] CPU: 1 UID: 0 PID: 9784 Comm: repro Not tainted 6.16.0-rc3 #7 PREEMPT(full) [ 174.854281][ T9784] Hardware name: QEMU Ubuntu 24.04 PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 [ 174.854286][ T9784] Call Trace: [ 174.854289][ T9784] <TASK> [ 174.854292][ T9784] dump_stack_lvl+0x10e/0x1f0 [ 174.854305][ T9784] print_report+0xd0/0x660 [ 174.854315][ T9784] ? __virt_addr_valid+0x81/0x610 [ 174.854323][ T9784] ? __phys_addr+0xe8/0x180 [ 174.854330][ T9784] ? hfsplus_bnode_read+0x2f4/0x360 [ 174.854337][ T9784] kasan_report+0xc6/0x100 [ 174.854346][ T9784] ? hfsplus_bnode_read+0x2f4/0x360 [ 174.854354][ T9784] hfsplus_bnode_read+0x2f4/0x360 [ 174.854362][ T9784] hfsplus_bnode_dump+0x2ec/0x380 [ 174.854370][ T9784] ? __pfx_hfsplus_bnode_dump+0x10/0x10 [ 174.854377][ T9784] ? hfsplus_bnode_write_u16+0x83/0xb0 [ 174.854385][ T9784] ? srcu_gp_start+0xd0/0x310 [ 174.854393][ T9784] ? __mark_inode_dirty+0x29e/0xe40 [ 174.854402][ T9784] hfsplus_brec_remove+0x3d2/0x4e0 [ 174.854411][ T9784] __hfsplus_delete_attr+0x290/0x3a0 [ 174.854419][ T9784] ? __pfx_hfs_find_1st_rec_by_cnid+0x10/0x10 [ 174.854427][ T9784] ? __pfx___hfsplus_delete_attr+0x10/0x10 [ 174.854436][ T9784] ? __asan_memset+0x23/0x50 [ 174.854450][ T9784] hfsplus_delete_all_attrs+0x262/0x320 [ 174.854459][ T9784] ? __pfx_hfsplus_delete_all_attrs+0x10/0x10 [ 174.854469][ T9784] ? rcu_is_watching+0x12/0xc0 [ 174.854476][ T9784] ? __mark_inode_dirty+0x29e/0xe40 [ 174.854483][ T9784] hfsplus_delete_cat+0x845/0xde0 [ 174.854493][ T9784] ? __pfx_hfsplus_delete_cat+0x10/0x10 [ 174.854507][ T9784] hfsplus_unlink+0x1ca/0x7c0 [ 174.854516][ T9784] ? __pfx_hfsplus_unlink+0x10/0x10 [ 174.854525][ T9784] ? down_write+0x148/0x200 [ 174.854532][ T9784] ? __pfx_down_write+0x10/0x10 [ 174.854540][ T9784] vfs_unlink+0x2fe/0x9b0 [ 174.854549][ T9784] do_unlinkat+0x490/0x670 [ 174.854557][ T9784] ? __pfx_do_unlinkat+0x10/0x10 [ 174.854565][ T9784] ? __might_fault+0xbc/0x130 [ 174.854576][ T9784] ? getname_flags.part.0+0x1c5/0x550 [ 174.854584][ T9784] __x64_sys_unlink+0xc5/0x110 [ 174.854592][ T9784] do_syscall_64+0xc9/0x480 [ 174.854600][ T9784] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 174.854608][ T9784] RIP: 0033:0x7f6fdf4c3167 [ 174.854614][ T9784] Code: f0 ff ff 73 01 c3 48 8b 0d 26 0d 0e 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 08 [ 174.854622][ T9784] RSP: 002b:00007ffcb948bca8 EFLAGS: 00000206 ORIG_RAX: 0000000000000057 [ 174.854630][ T9784] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f6fdf4c3167 [ 174.854636][ T9784] RDX: 00007ffcb948bcc0 RSI: 00007ffcb948bcc0 RDI: 00007ffcb948bd50 [ 174.854641][ T9784] RBP: 00007ffcb948cd90 R08: 0000000000000001 R09: 00007ffcb948bb40 [ 174.854645][ T9784] R10: 00007f6fdf564fc0 R11: 0000000000000206 R12: 0000561e1bc9c2d0 [ 174.854650][ T9784] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 174.854658][ T9784] </TASK> [ 174.854661][ T9784] [ 174.879281][ T9784] Allocated by task 9784: [ 174.879664][ T9784] kasan_save_stack+0x20/0x40 [ 174.880082][ T9784] kasan_save_track+0x14/0x30 [ 174.880500][ T9784] __kasan_kmalloc+0xaa/0xb0 [ 174.880908][ T9784] __kmalloc_noprof+0x205/0x550 [ 174.881337][ T9784] __hfs_bnode_create+0x107/0x890 [ 174.881779][ T9784] hfsplus_bnode_find+0x2d0/0xd10 [ 174.882222][ T9784] hfsplus_brec_find+0x2b0/0x520 [ 174.882659][ T9784] hfsplus_delete_all_attrs+0x23b/0x320 [ 174.883144][ T9784] hfsplus_delete_cat+0x845/0xde0 [ 174.883595][ T9784] hfsplus_rmdir+0x106/0x1b0 [ 174.884004][ T9784] vfs_rmdir+0x206/0x690 [ 174.884379][ T9784] do_rmdir+0x2b7/0x390 [ 174.884751][ T9784] __x64_sys_rmdir+0xc5/0x110 [ 174.885167][ T9784] do_syscall_64+0xc9/0x480 [ 174.885568][ T9784] entry_SYSCALL_64_after_hwframe+0x77/0x7f [ 174.886083][ T9784] [ 174.886293][ T9784] The buggy address belongs to the object at ffff88810b5fc600 [ 174.886293][ T9784] which belongs to the cache kmalloc-192 of size 192 [ 174.887507][ T9784] The buggy address is located 40 bytes to the right of [ 174.887507][ T9784] allocated 152-byte region [ffff88810b5fc600, ffff88810b5fc698) [ 174.888766][ T9784] [ 174.888976][ T9784] The buggy address belongs to the physical page: [ 174.889533][ T9784] page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x10b5fc [ 174.890295][ T9784] flags: 0x57ff00000000000(node=1|zone=2|lastcpupid=0x7ff) [ 174.890927][ T9784] page_type: f5(slab) [ 174.891284][ T9784] raw: 057ff00000000000 ffff88801b4423c0 ffffea000426dc80 dead000000000002 [ 174.892032][ T9784] raw: 0000000000000000 0000000080100010 00000000f5000000 0000000000000000 [ 174.892774][ T9784] page dumped because: kasan: bad access detected [ 174.893327][ T9784] page_owner tracks the page as allocated [ 174.893825][ T9784] page last allocated via order 0, migratetype Unmovable, gfp_mask 0x52c00(GFP_NOIO|__GFP_NOWARN|__GFP_NO1 [ 174.895373][ T9784] post_alloc_hook+0x1c0/0x230 [ 174.895801][ T9784] get_page_from_freelist+0xdeb/0x3b30 [ 174.896284][ T9784] __alloc_frozen_pages_noprof+0x25c/0x2460 [ 174.896810][ T9784] alloc_pages_mpol+0x1fb/0x550 [ 174.897242][ T9784] new_slab+0x23b/0x340 [ 174.897614][ T9784] ___slab_alloc+0xd81/0x1960 [ 174.898028][ T9784] __slab_alloc.isra.0+0x56/0xb0 [ 174.898468][ T9784] __kmalloc_noprof+0x2b0/0x550 [ 174.898896][ T9784] usb_alloc_urb+0x73/0xa0 [ 174.899289][ T9784] usb_control_msg+0x1cb/0x4a0 [ 174.899718][ T9784] usb_get_string+0xab/0x1a0 [ 174.900133][ T9784] usb_string_sub+0x107/0x3c0 [ 174.900549][ T9784] usb_string+0x307/0x670 [ 174.900933][ T9784] usb_cache_string+0x80/0x150 [ 174.901355][ T9784] usb_new_device+0x1d0/0x19d0 [ 174.901786][ T9784] register_root_hub+0x299/0x730 [ 174.902231][ T9784] page last free pid 10 tgid 10 stack trace: [ 174.902757][ T9784] __free_frozen_pages+0x80c/0x1250 [ 174.903217][ T9784] vfree.part.0+0x12b/0xab0 [ 174.903645][ T9784] delayed_vfree_work+0x93/0xd0 [ 174.904073][ T9784] process_one_work+0x9b5/0x1b80 [ 174.904519][ T9784] worker_thread+0x630/0xe60 [ 174.904927][ T9784] kthread+0x3a8/0x770 [ 174.905291][ T9784] ret_from_fork+0x517/0x6e0 [ 174.905709][ T9784] ret_from_fork_asm+0x1a/0x30 [ 174.906128][ T9784] [ 174.906338][ T9784] Memory state around the buggy address: [ 174.906828][ T9784] ffff88810b5fc580: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc [ 174.907528][ T9784] ffff88810b5fc600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 [ 174.908222][ T9784] >ffff88810b5fc680: 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc [ 174.908917][ T9784] ^ [ 174.909481][ T9784] ffff88810b5fc700: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 174.910432][ T9784] ffff88810b5fc780: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc [ 174.911401][ T9784] ================================================================== The reason of the issue that code doesn't check the correctness of the requested offset and length. As a result, incorrect value of offset or/and length could result in access out of allocated memory. This patch introduces is_bnode_offset_valid() method that checks the requested offset value. Also, it introduces check_and_correct_requested_length() method that checks and correct the requested length (if it is necessary). These methods are used in hfsplus_bnode_read(), hfsplus_bnode_write(), hfsplus_bnode_clear(), hfsplus_bnode_copy(), and hfsplus_bnode_move() with the goal to prevent the access out of allocated memory and triggering the crash. Reported-by: Kun Hu <huk23@m.fudan.edu.cn> Reported-by: Jiaji Qin <jjtan24@m.fudan.edu.cn> Reported-by: Shuoran Bai <baishuoran@hrbeu.edu.cn> Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Link: https://lore.kernel.org/r/20250703214804.244077-1-slava@dubeyko.com Signed-off-by: Viacheslav Dubeyko <slava@dubeyko.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 48918ca ] The test starts a workload and then opens events. If the events fail to open, for example because of perf_event_paranoid, the gopipe of the workload is leaked and the file descriptor leak check fails when the test exits. To avoid this cancel the workload when opening the events fails. Before: ``` $ perf test -vv 7 7: PERF_RECORD_* events & perf_sample fields: --- start --- test child forked, pid 1189568 Using CPUID GenuineIntel-6-B7-1 ------------------------------------------------------------ perf_event_attr: type 0 (PERF_TYPE_HARDWARE) config 0xa00000000 (cpu_atom/PERF_COUNT_HW_CPU_CYCLES/) disabled 1 ------------------------------------------------------------ sys_perf_event_open: pid 0 cpu -1 group_fd -1 flags 0x8 sys_perf_event_open failed, error -13 ------------------------------------------------------------ perf_event_attr: type 0 (PERF_TYPE_HARDWARE) config 0xa00000000 (cpu_atom/PERF_COUNT_HW_CPU_CYCLES/) disabled 1 exclude_kernel 1 ------------------------------------------------------------ sys_perf_event_open: pid 0 cpu -1 group_fd -1 flags 0x8 = 3 ------------------------------------------------------------ perf_event_attr: type 0 (PERF_TYPE_HARDWARE) config 0x400000000 (cpu_core/PERF_COUNT_HW_CPU_CYCLES/) disabled 1 ------------------------------------------------------------ sys_perf_event_open: pid 0 cpu -1 group_fd -1 flags 0x8 sys_perf_event_open failed, error -13 ------------------------------------------------------------ perf_event_attr: type 0 (PERF_TYPE_HARDWARE) config 0x400000000 (cpu_core/PERF_COUNT_HW_CPU_CYCLES/) disabled 1 exclude_kernel 1 ------------------------------------------------------------ sys_perf_event_open: pid 0 cpu -1 group_fd -1 flags 0x8 = 3 Attempt to add: software/cpu-clock/ ..after resolving event: software/config=0/ cpu-clock -> software/cpu-clock/ ------------------------------------------------------------ perf_event_attr: type 1 (PERF_TYPE_SOFTWARE) size 136 config 0x9 (PERF_COUNT_SW_DUMMY) sample_type IP|TID|TIME|CPU read_format ID|LOST disabled 1 inherit 1 mmap 1 comm 1 enable_on_exec 1 task 1 sample_id_all 1 mmap2 1 comm_exec 1 ksymbol 1 bpf_event 1 { wakeup_events, wakeup_watermark } 1 ------------------------------------------------------------ sys_perf_event_open: pid 1189569 cpu 0 group_fd -1 flags 0x8 sys_perf_event_open failed, error -13 perf_evlist__open: Permission denied ---- end(-2) ---- Leak of file descriptor 6 that opened: 'pipe:[14200347]' ---- unexpected signal (6) ---- iFailed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon Failed to read build ID for //anon #0 0x565358f6666e in child_test_sig_handler builtin-test.c:311 #1 0x7f29ce849df0 in __restore_rt libc_sigaction.c:0 #2 0x7f29ce89e95c in __pthread_kill_implementation pthread_kill.c:44 #3 0x7f29ce849cc2 in raise raise.c:27 #4 0x7f29ce8324ac in abort abort.c:81 #5 0x565358f662d4 in check_leaks builtin-test.c:226 #6 0x565358f6682e in run_test_child builtin-test.c:344 #7 0x565358ef7121 in start_command run-command.c:128 #8 0x565358f67273 in start_test builtin-test.c:545 #9 0x565358f6771d in __cmd_test builtin-test.c:647 #10 0x565358f682bd in cmd_test builtin-test.c:849 #11 0x565358ee5ded in run_builtin perf.c:349 #12 0x565358ee6085 in handle_internal_command perf.c:401 #13 0x565358ee61de in run_argv perf.c:448 #14 0x565358ee6527 in main perf.c:555 #15 0x7f29ce833ca8 in __libc_start_call_main libc_start_call_main.h:74 #16 0x7f29ce833d65 in __libc_start_main@@GLIBC_2.34 libc-start.c:128 #17 0x565358e391c1 in _start perf[851c1] 7: PERF_RECORD_* events & perf_sample fields : FAILED! ``` After: ``` $ perf test 7 7: PERF_RECORD_* events & perf_sample fields : Skip (permissions) ``` Fixes: 16d00fe ("perf tests: Move test__PERF_RECORD into separate object") Signed-off-by: Ian Rogers <irogers@google.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Athira Rajeev <atrajeev@linux.ibm.com> Cc: Chun-Tse Shao <ctshao@google.com> Cc: Howard Chu <howardchu95@gmail.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@linaro.org> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>

commit 0570327 upstream. Before disabling SR-IOV via config space accesses to the parent PF, sriov_disable() first removes the PCI devices representing the VFs. Since commit 9d16947 ("PCI: Add global pci_lock_rescan_remove()") such removal operations are serialized against concurrent remove and rescan using the pci_rescan_remove_lock. No such locking was ever added in sriov_disable() however. In particular when commit 18f9e9d ("PCI/IOV: Factor out sriov_add_vfs()") factored out the PCI device removal into sriov_del_vfs() there was still no locking around the pci_iov_remove_virtfn() calls. On s390 the lack of serialization in sriov_disable() may cause double remove and list corruption with the below (amended) trace being observed: PSW: 0704c00180000000 0000000c914e4b38 (klist_put+56) GPRS: 000003800313fb48 0000000000000000 0000000100000001 0000000000000001 00000000f9b520a8 0000000000000000 0000000000002fbd 00000000f4cc9480 0000000000000001 0000000000000000 0000000000000000 0000000180692828 00000000818e8000 000003800313fe2c 000003800313fb20 000003800313fad8 #0 [3800313fb20] device_del at c9158ad5c #1 [3800313fb88] pci_remove_bus_device at c915105ba #2 [3800313fbd0] pci_iov_remove_virtfn at c9152f198 #3 [3800313fc28] zpci_iov_remove_virtfn at c90fb67c0 #4 [3800313fc60] zpci_bus_remove_device at c90fb6104 #5 [3800313fca0] __zpci_event_availability at c90fb3dca #6 [3800313fd08] chsc_process_sei_nt0 at c918fe4a2 #7 [3800313fd60] crw_collect_info at c91905822 #8 [3800313fe10] kthread at c90feb390 #9 [3800313fe68] __ret_from_fork at c90f6aa64 #10 [3800313fe98] ret_from_fork at c9194f3f2. This is because in addition to sriov_disable() removing the VFs, the platform also generates hot-unplug events for the VFs. This being the reverse operation to the hotplug events generated by sriov_enable() and handled via pdev->no_vf_scan. And while the event processing takes pci_rescan_remove_lock and checks whether the struct pci_dev still exists, the lack of synchronization makes this checking racy. Other races may also be possible of course though given that this lack of locking persisted so long observable races seem very rare. Even on s390 the list corruption was only observed with certain devices since the platform events are only triggered by config accesses after the removal, so as long as the removal finished synchronously they would not race. Either way the locking is missing so fix this by adding it to the sriov_del_vfs() helper. Just like PCI rescan-remove, locking is also missing in sriov_add_vfs() including for the error case where pci_stop_and_remove_bus_device() is called without the PCI rescan-remove lock being held. Even in the non-error case, adding new PCI devices and buses should be serialized via the PCI rescan-remove lock. Add the necessary locking. Fixes: 18f9e9d ("PCI/IOV: Factor out sriov_add_vfs()") Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Farhan Ali <alifm@linux.ibm.com> Reviewed-by: Julian Ruess <julianr@linux.ibm.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250826-pci_fix_sriov_disable-v1-1-2d0bc938f2a3@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 163e5f2b96632b7fb2eaa965562aca0dbdf9f996 ] When using perf record with the `--overwrite` option, a segmentation fault occurs if an event fails to open. For example: perf record -e cycles-ct -F 1000 -a --overwrite Error: cycles-ct:H: PMU Hardware doesn't support sampling/overflow-interrupts. Try 'perf stat' perf: Segmentation fault #0 0x6466b6 in dump_stack debug.c:366 #1 0x646729 in sighandler_dump_stack debug.c:378 #2 0x453fd1 in sigsegv_handler builtin-record.c:722 #3 0x7f8454e65090 in __restore_rt libc-2.32.so[54090] #4 0x6c5671 in __perf_event__synthesize_id_index synthetic-events.c:1862 #5 0x6c5ac0 in perf_event__synthesize_id_index synthetic-events.c:1943 #6 0x458090 in record__synthesize builtin-record.c:2075 #7 0x45a85a in __cmd_record builtin-record.c:2888 #8 0x45deb6 in cmd_record builtin-record.c:4374 #9 0x4e5e33 in run_builtin perf.c:349 #10 0x4e60bf in handle_internal_command perf.c:401 #11 0x4e6215 in run_argv perf.c:448 #12 0x4e653a in main perf.c:555 #13 0x7f8454e4fa72 in __libc_start_main libc-2.32.so[3ea72] #14 0x43a3ee in _start ??:0 The --overwrite option implies --tail-synthesize, which collects non-sample events reflecting the system status when recording finishes. However, when evsel opening fails (e.g., unsupported event 'cycles-ct'), session->evlist is not initialized and remains NULL. The code unconditionally calls record__synthesize() in the error path, which iterates through the NULL evlist pointer and causes a segfault. To fix it, move the record__synthesize() call inside the error check block, so it's only called when there was no error during recording, ensuring that evlist is properly initialized. Fixes: 4ea648a ("perf record: Add --tail-synthesize option") Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>

ts-kris requested review from lionel, luckshot, markfeathers and randytsi369 January 6, 2023 23:10

ts-kris force-pushed the linux-5.10.y-ts7990-support branch 2 times, most recently from 8d3ed11 to 94938a0 Compare January 10, 2023 20:19

luckshot previously approved these changes Jan 10, 2023

View reviewed changes

Mark Featherston and others added 2 commits January 20, 2023 16:16

ts-kris dismissed luckshot’s stale review via a1e2b29 January 21, 2023 00:00

ts-kris force-pushed the linux-5.10.y-ts7990-support branch from 94938a0 to a1e2b29 Compare January 21, 2023 00:00

ts-kris requested a review from luckshot January 21, 2023 00:01

ts-kris force-pushed the linux-5.10.y-ts7990-support branch from a1e2b29 to 99f0a0a Compare January 24, 2023 22:07

markfeathers approved these changes Feb 6, 2023

View reviewed changes

luckshot approved these changes Feb 7, 2023

View reviewed changes

ts-kris merged commit b3b9df5 into linux-5.10.y Feb 7, 2023

ts-kris deleted the linux-5.10.y-ts7990-support branch February 7, 2023 00:24

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Initial TS-7990 support#7

Initial TS-7990 support#7
ts-kris merged 3 commits intolinux-5.10.yfrom
linux-5.10.y-ts7990-support

ts-kris commented Jan 6, 2023

Uh oh!

ts-kris commented Jan 20, 2023

Uh oh!

ts-kris commented Jan 21, 2023

Uh oh!

ts-kris commented Jan 24, 2023

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

3 participants

Conversation

ts-kris commented Jan 6, 2023

Uh oh!

ts-kris commented Jan 20, 2023

Uh oh!

ts-kris commented Jan 21, 2023

Uh oh!

ts-kris commented Jan 24, 2023

Uh oh!

Reviewers

Assignees

Labels

Projects

Milestone

Development

Uh oh!

3 participants