NoDon SIN-4-FP-21 Versatile don't change status mode

[Lours373]

Dear,
I'm trying to configure a simple electric heater with NoDon module with pilot wire.
I follow the readme integration but it doesn't work.
First of all, with ZHA a can change the mode of my heater without any problems.

I proceed as follow to configure Versatile (suppose my mistake is due to bad configuration or comprehension)

There is no Function added, as I have not sensor for door, presence...

For the sub-jacent,

for the start and stop command, I'm not sure if i write it well...
so in my state I've this options for the Nodon :

Finally, when the thermostat on my dashboard is in heat mode, and the mode is on Confort,

this is the status of the versatile
'''
hvac_modes: heat, off
min_temp: 7
max_temp: 35
target_temp_step: 0.1
preset_modes: none, frost, eco, comfort, boost
current_temperature: 21.4
temperature: 24
hvac_action: idle
preset_mode: comfort
is_on: true
hvac_mode: heat
type: null
is_controlled_by_central_mode: false
last_central_mode: null
frost_temp: 7
eco_temp: 16
boost_temp: 30
comfort_temp: 24
frost_away_temp: 0
eco_away_temp: 0
boost_away_temp: 0
comfort_away_temp: 0
target_temperature_step: 0.1
ext_current_temperature: 13.3
ac_mode: false
saved_preset_mode: comfort
saved_target_temp: 24.700000000000003
saved_hvac_mode: off
last_temperature_datetime: 2025-03-18T16:19:29.418712+01:00
last_ext_temperature_datetime: 2025-03-18T16:19:29.418712+01:00
minimal_activation_delay_sec: 10
minimal_deactivation_delay_sec: 0
total_energy: 0.33
last_update_datetime: 2025-03-18T16:19:29.424997+01:00
timezone: Europe/Brussels
temperature_unit: °C
is_device_active: false
device_actives:
nb_device_actives: 0
ema_temp: 21.65
is_used_by_central_boiler: false
temperature_slope: -0.59
hvac_off_reason: null
max_on_percent: null
have_valve_regulation: false
last_change_time_from_vtherm: 2025-03-18T16:19:21.620739+01:00
presence_sensor_entity_id: null
presence_state: unavailable
is_presence_configured: false
power_sensor_entity_id: null
max_power_sensor_entity_id: null
overpowering_state: unavailable
is_power_configured: false
device_power: 1
power_temp: null
current_power: null
current_max_power: null
mean_cycle_power: 1
motion_sensor_entity_id: null
motion_state: unavailable
is_motion_configured: false
motion_delay_sec: 0
motion_off_delay_sec: 0
motion_preset: null
no_motion_preset: null
window_state: unavailable
window_auto_state: unavailable
window_action: window_turn_off
is_window_bypass: false
window_sensor_entity_id: null
window_delay_sec: null
window_off_delay_sec: null
is_window_configured: false
is_window_auto_configured: false
window_auto_open_threshold: null
window_auto_close_threshold: null
window_auto_max_duration: null
is_safety_configured: true
safety_state: off
safety_delay_min: 60
safety_min_on_percent: 0.5
safety_default_on_percent: 0.1
is_over_switch: true
is_inversed: false
keep_alive_sec: 0
underlying_entities: select.chauffage_sdb_mode_du_fil_pilote
on_percent: 1
power_percent: 100
on_time_sec: 300
off_time_sec: 0
cycle_min: 5
function: tpi
tpi_coef_int: 0.6
tpi_coef_ext: 0.01
calculated_on_percent: 1
vswitch_on_commands: select_option/option:comfort
vswitch_off_commands: select_option/option:frostprotection
friendly_name: Chauffage_SDB_Versatile
supported_features: 401
'''

When I go to the historic of my dashboard Therostat, is saw this, is it the cause of my problem? CVC is not properly configured?

Thanks a lot for your help

[Lours373]

So, I find my mistakes, durong configuration I place the switch On OFF of the NoDon module instead of the selection mode.
because an error occured first time i tryied to configure it with this entity.

Question more, only confort mode is sent to my heater, I tryied to add the command for the Eco mode, but error occured..
is it normal?
Command added is : select_option/option:Eco

[jmcollin78]

It is likely because Eco is not supported by your Nodon. You have to look all options possible in the Development Tools/state. Select your Nodon and you will have all possible options.

[Lours373]

The Eco mode exist and I can manually place the mode Eco,
As explain in my first post this is all mode read from the NodOn Module

Eco, confort, off, are recognized

[jmcollin78]

ok. I have no idea what happens with the Eco.