Repository navigation
Releases
Releases · manfredi90/OSSC-Downscaler
v1.5
New
- 2nd button on the OSSC: short press = 240p / 480i, long press (1 second) = next HD format (Full 16:9 / Center 4:3 / Wide)
- 1024x768 input (60Hz, VESA standard timing 1344x806): 240p and 480i, 3 lines per output line, use the 960x720 center window (32 pixels and 24 lines cropped per side).
- 1280x1024 input (60Hz, VESA standard timing 1688x1066): 240p and 480i, 4 lines per output line, use the 960 center lines.
- "Flicker filter" also for HD and PC sources with 480i output: 1080p Full / Center 4:3, 1280x1024, 1280x960, 720p Wide, 720p Full / Center 4:3 and 1024x768. With no input lines left below the picture (720p phase 2, 720p Wide phases 2-3, 1280x960 phases 1-3) the filter is off.
Changed
- Output PLL: VCO at least 650MHz (was 600MHz, the datasheet minimum), for more margin. Same output timings; only the PLL multipliers change for some modes.
Installation
- Copy
ossc_ds_v1.5.binto a micro SD card. - Install it from the official firmware's firmware update function (it is written to the secondary slot only).
- Start it with Launch 2nd FW, then select the input with the remote.
v1.4
New
- HDMI range (menu): Full (0-255), Limited (16-235), Limited (16-255), as the MiSTer's Direct Video options. Useful with HDMI-to-VGA DACs that crush blacks or clip whites. Applies to every output.
- Test pattern (last menu item): Gray (the stock pattern), Grid, Monoscope, RGB. Shown at start, with no sync or an unsupported input (select an unused input to see it). Useful to adjust the CRT's geometry, convergence and levels, and to choose the HDMI range.
Installation
- Copy
ossc_ds_v1.4.binto a micro SD card. - Install it from the official firmware's firmware update function (it is written to the secondary slot only).
- Start it with Launch 2nd FW, then select the input with the remote.
v1.3
New
- 1280x960 input (60Hz, VESA standard timing 1800x1000): 240p and 480i
- 1080p Wide is now 216p: More detail than the 180p mode it replaces;
- H. / V. position in passthrough (240p, 480i, 480i -> 240p): the picture moves without being changed; past the porch limits the edges are cropped.
- Menu: "480i input" is now "15kHz input", "480i filter" is now "Flicker filter".
Fixed
- 4-line blending was 1 low on odd values (rounding).
Notes
- Not every HDMI-to-VGA DAC handles 15kHz signals: DACs that work with the MiSTer FPGA's Direct Video mode generally work; if the picture doesn't sync, try the other "CSync on HSYNC" settings.
Installation
- Copy
ossc_ds_v1.3.binto a micro SD card. - Install it from the official firmware's firmware update function (it is written to the secondary slot only).
- Start it with Launch 2nd FW, then select the input with the remote.
Power cycle the OSSC to return to the official firmware. Settings saved with earlier versions are kept.
v1.2
New
- 1080p Wide (180p): the whole 16:9 picture letterboxed, 240p and 480i output.
- 576p input (50Hz): 288p and 576i output support. Optional flicker filter in 576i.
- 576i -> 288p conversion: verified on hardware (PS2).
Installation
- Copy
ossc_ds_v1.2.binto a micro SD card. - Install it from the official firmware's firmware update function (it is written to the secondary slot only).
- Start it with Launch 2nd FW, then select the input with the remote.
Power cycle the OSSC to return to the official firmware. Settings saved with earlier versions are kept.
v1.1
New
- 1080p input (60Hz), 240p and 480i output, 4 input lines per output line:
- Full 16:9: the 1708x960 center window (~89% of the picture, like a TV's overscan), squeezed to 4:3
- Center 4:3: the 1280x960 center window
- 480i input → 240p (menu "480i input"): 480i sources can be shown as 240p, with both fields on the same scanlines (no interlacing). Passthrough stays the default.
- 480i flicker filter (menu "480i filter", Off / 1–4): for 480p and 640x480 sources with 480i output, each field line is mixed with the lines above and below (weights a, 1-2a, a; level 4 = 1/4, 1/2, 1/4), as in the flicker filter of professional scan converters.
- Component input (YPbPr) verified.
Changes and fixes
- Wide (180p): fixed the sampling phase (it sampled on the pixel edges, causing shimmer on motion).
- Output line rate limits narrowed to 14.8–16.0kHz (computed modes stay within 15.6–15.9kHz), hardware watchdog threshold lowered to 16.4kHz.
Installation
- Copy
ossc_ds_v1.1.binto a micro SD card. - Install it from the official firmware's firmware update function (it is written to the secondary slot only).
- Start it with Launch 2nd FW, then select the input with the remote.
Power cycle the OSSC to return to the official firmware. Settings saved with v1.0 are kept.
v1.0
First release of the OSSC Downscaler firmware: an unofficial secondary firmware for the OSSC that converts HD and 31kHz sources on the VGA input to 15kHz 240p or 480i on HDMI, frame locked to the input (no added frame of lag). It runs from the secondary firmware slot and never touches the official firmware.
Unofficial, experimental and AI-assisted. Use at your own risk. See the README for details.
Features
- Based on the official OSSC firmware, with a dedicated downscaler menu
- Controlled from the standard OSSC on-screen menu with the remote control
- Inputs: 1280x720p, 720x480p, 640x480p
- Outputs: 240p (260–264 lines, 15.6–15.9kHz) or 480i (525 lines)
- 720p formats: Full 16:9 (squeezed), Center 4:3, Wide (180p letterbox)
- Full resolution sampling with an exact output clock ratio: smooth horizontal scrolling
- Composite sync on HSYNC for SCART: Off (H+V), XOR, AND, Standard (equalizing pulses + serrated vsync)
- Line blending, line phase, adjustable width and position, manual 480p / 640x480 input selection
- Ability to save settings, independent of the official profiles