Skip to content

Releases

Satellite Bridge 1.0.7 - AO-7 tracking repair

Choose a tag to compare

@matpet matpet released this 26 Oct 19:52

Version 1.0.7 build 11 fixes two faults seen while tracking AO-7 through RUMlogNG 6.6.1.

When AO-7 requests 2 m RX and 70 cm TX, the bridge now exchanges Main/Sub before tuning if TX occupies the requested RX band. Both bands verify before frequency setters; recalled TX power is held within 5% during transition. MacDoppler's 80% default follows only after its target frequency/mode verifies.

Continuous tracking keeps control of VFO selection across updates and restores the original panel view when leaving tracking or closing. Readouts use current AX elements. Frequency-only updates reuse the verified RX filter; mode/band changes or a reported mismatch reapply its rule.

131 local tests passed. A controlled real-radio replay verified automatic QO-100/AO-7 transitions and 60 consecutive pairs, with CW RX filter 2 and 80% during tracking, then QO-100 restoration at 4%. The installed app also passed three labeled validation packets and CW restoration after Accessibility renewal. These are panel/control checks, not an over-the-air contact or RF measurement. At the tested 19200 baud, control/readback averages about four seconds per pair; the newest pending report is retained.

RUMlogNG remains the sole physical CAT owner. TX CTCSS, receiver profiles, QO-100 manual tuning, virtual split and the 5% converter ceiling are retained. The app never keys PTT.

The README and supplied guide include the current build 11 screenshot. Intel macOS; Python/Tk bundled. Ad-hoc signed, not Developer ID signed or notarized. Replacing an existing executable may require renewing its Accessibility entry. Existing saved pairs and RUMlogNG macros are preserved.

Satellite Bridge 1.0.6 - tracking, tones and QO-100 split

Choose a tag to compare

@matpet matpet released this 26 Oct 17:45

Superseded by 1.0.7. Version 1.0.6 can pause when RX/TX bands reverse, as for AO-7, or while restoring panel selection during tracking. Version 1.0.7 repairs both faults.

Satellite Bridge 1.0.6 build 10 adds SAT-preserving selected-VFO tracking for RUMlogNG 6.6.1, panel TX CTCSS, receiver profiles and QO-100 virtual split. RUMlogNG remains the sole physical CAT owner.

  • Both sources: RX filter 2 for CW/CW-R; RX filter 1 for USB/USB-D. RX-filter selection leaves TX filter unchanged.
  • MacDoppler: separate RX/TX UDP updates, TX CTCSS 74.4/67/off through the panel, separate RX TSQL, ATT off/internal preamp on and external 70 cm preamp command for a 70 cm downlink.
  • MacDoppler TX defaults to 80% after its target verifies, on entry or TX band/mode changes. Frequency-only updates preserve later manual power adjustment.
  • QO-100: manual radio tuning is preserved, RX ATT on/preamps off and the 5% power ceiling remain.
  • QO-100 virtual split: USB/USB-D +5/+10/+15 kHz; CW/CW-R +1/+2/+3 kHz. The actual TX base is remembered; Off restores it exactly without stacking offsets or changing RX.

118 local tests passed. Controlled UDP replay applied 13 updates through the real IC-9700, including captured FO-29 reports, modes, filters, tone transitions, receiver profiles, 80% defaults and both split ranges. These are control/readback checks; no new over-the-air contact or independent external-amplifier measurement is claimed.

Installed build 10 passed its GUI/Accessibility check after access renewal. Digital/CW, RX filters, SAT, 4% power and observed split/base restoration verified. Its executable matches the packaged build, and strict signature verification passed after extracting the final ZIP. This is a public preview for continued station testing.

Intel macOS app; Python/Tk bundled. Locally ad-hoc signed, not Developer ID signed or notarized. Review the guide before connecting another station. Default receiver macros use IC-9700 CI-V address A2 and occupy unused RUMlogNG manual slots; existing macros are preserved.

Documentation updated: the README, user guide and PDF now show the actual 1.0.6 build 10 CW window, including virtual split and RX filter 2. The release ZIP includes the refreshed PDF; checksums have been updated. The app executable is unchanged.

Satellite Bridge 1.0.5 - RUMlogNG compatibility repair

Choose a tag to compare

@matpet matpet released this 26 Oct 07:08

Known compatibility issues — 26 October 2026

Subsequent live testing found that this release is not a complete RUMlogNG 6.6.1 tracking repair. QO-100 preset changes can leave the TX mode incorrect, and MacDoppler TX frequency tracking is unreliable with SAT enabled. The development preview also encountered frequency-feedback timeouts; it remains paused and has not been released as 1.0.6.

The UDP Broadcast route cannot provide MacDoppler's native Tuning Dial Tracking. The downloadable app also does not forward MacDoppler's TX CTCSS or RX tone-squelch settings. SO-50 tone operation and radio-knob tracking during passes are therefore not validated features of this release.

Development retains RUMlogNG as the sole physical CAT owner. A two-way virtual-radio route is under investigation; a protocol simulation is not a working radio backend. The downloads below are unchanged and remain a prerelease. The validation below describes the narrower checks performed before these additional limitations were found.


Satellite Bridge 1.0.5 repairs IC-9700 control-panel lookup and Digital startup with RUMlogNG 6.6.1. The Intel macOS app is build 7.

Fixes

  • Accept both full and compact Main/RX and Sub/TX control labels.
  • Read frequency, mode and filter by content when fields move or the TX Data field is omitted.
  • Reject placeholder modes and use the live mode buttons only for their unambiguously selected VFO. The same fallback now supports RX-filter verification, fixing the startup RX-mode timeout.

QO-100 still applies one batch of tuning commands per selection and keeps its 5% power ceiling. Saved pairs remain outside the app and are preserved.

Updating

Replace the existing app with the copy in the ZIP. This app is ad-hoc signed, not Developer ID signed or notarized. macOS may require you to remove the previous Satellite Bridge entry from System Settings > Privacy & Security > Accessibility, then add and enable the updated installed app. The bridge holds tuning and retries automatically until access and power feedback return. Its normal startup then applies Digital once.

For a different station, keep RUMlogNG closed while configuring the supplied dial/IF examples. Retain exactly one pair named Digital.

Validation

The publication source passes 60 local regression tests using simulated radio endpoints. The installed app was also checked on the original Intel Mac with macOS 15.7.3 and RUMlogNG 6.6.1: Digital reached active status, feedback verified RX 433.540000 MHz and TX 144.040000 MHz, RX filter 1, SAT on and power at 4%. Exactly four tuning setters were recorded, with no repeat during the stability check. Saved presets were unchanged.

No MacDoppler packets arrived during this repair check; this release does not claim a new live UDP or over-the-air test. Earlier independent RX/TX checks are summarized separately in Validation.

Downloads

  • Satellite-Bridge-1.0.5-macOS-Intel.zip: app, updated PDF guide, MIT license and complete bundled-runtime notices.
  • Satellite-Bridge-Guide-1.0.5.pdf: standalone six-page guide.
  • SHA256SUMS.txt: checksums for both downloads.

The ZIP has been extracted and its app signature and executable checked against the tested build. The running installed app was not replaced during publication.

Remaining limitations

Feedback reads still force RUMlogNG Toggle on. Terrestrial profiles, CTCSS forwarding and 80% power defaults remain planned. The 5% guard monitors a reported software setting; it is not an RF measurement or a hardware limiter. No native Apple Silicon build is supplied.

Satellite Bridge 1.0.4 - first public preview

Choose a tag to compare

@matpet matpet released this 25 Oct 15:21

Satellite Bridge keeps RUMlogNG as the sole CAT controller of the IC-9700, configured as TRX2. MacDoppler sends UDP radio reports to the bridge; selected frequencies and modes are forwarded to RUMlogNG over TCP.

This is the first public preview of the existing 1.0.4 Intel macOS build.

Included

  • Compact QO-100 pair list and separate Settings editor.
  • QO-100 frequency/mode commands sent once per selection; manual tuning remains available.
  • Continuing, independent uplink/downlink updates only while MacDoppler is selected.
  • Default Digital startup with MacDoppler blocked.
  • QO-100 power ceiling of 5%, with feedback and automatic power-read recovery.
  • RX filter 2 for CW/CW-R; RX filter 1 for USB/USB-D.
  • Actual RUMlogNG panel readback, source indicators and visible incoming UDP packets.
  • Design rationale, setup/operating documentation, a real app screenshot, and a six-page PDF guide.

Downloads

  • Satellite-Bridge-1.0.4-macOS-Intel.zip: app, PDF guide, MIT license and bundled-runtime notices.
  • Satellite-Bridge-Guide-1.0.4.pdf: standalone illustrated guide.
  • SHA256SUMS.txt: checksums for the two downloads.

The app bundles Python 3.12.14 and Tcl/Tk 9.0.4. It was tested on Intel macOS 15.7.3 with RUMlogNG 6.5.1 and MacDoppler 2.48. It is locally ad-hoc signed, not Developer ID signed or notarized. Native Apple Silicon compatibility has not been validated.

Current limitations

  • Feedback reads still force RUMlogNG's Toggle control on. Preserving the operator's setting is planned, not fixed in 1.0.4.
  • RUMlogNG can briefly display a requested frequency before later CAT feedback differs. The app checks stable QO-100 readback and reports a mismatch without automatically retrying a frequency setter.
  • The 5% guard is software with feedback latency, not a hardware RF limiter.
  • Repeater/simplex profiles, CTCSS forwarding and 80% power defaults for MacDoppler/terrestrial operation are planned, not included. This version does not automatically raise power when selecting MacDoppler.

The clean source passes 50 local regression tests. Earlier independent live RX/TX checks and the final one-shot startup observation are summarized in Validation.

Original bridge code and documentation are MIT licensed. Bundled runtime components retain their own licenses.