Repository navigation
Range Walk Comparison
Purpose: Compare receiver-reported RF evidence from repeated EdgeTX telemetry recordings along the same five-landmark walking route. Walk 1 fixes the baseline route, landmarks and radio configuration; later walks are compared with it in four outward sections.
- One EdgeTX telemetry
.csvfile for each walk. No aircraft BIN is required. - Five identifiable physical landmarks in a safe outward route. Landmark 5 is the turnaround.
- Deliberate sustained full elevator-down holds followed by neutral at each landmark.
- Notes describing the transmitter, receiver, antennas, placement, orientation and configured RF settings.
- The APT desktop GUI. Read Test Procedure before recording a walk.
Keep each CSV within one fresh transmitter power-on and logging session. Preserve the original files and record what changed between walks. The aircraft must remain stationary and disarmed with the propeller removed.
- Open Range-Walk Comparison from Overview or select its tab. The shared Source BIN: selection does not apply to this CSV workflow.
- On CSV & Markers, click Choose CSV… and select the EdgeTX recording.
- Leave Automatic (recommended) selected and click Detect markers. Automatic mode evaluates sustained deflections and neutral returns in both numerical directions; it does not assume whether elevator-down is positive or negative in the transmitter log.
- Review every candidate's onset, release and hold duration. Detection finds control movements, not confirmed physical landmarks.
- If Automatic chose the wrong direction, select Opposite direction and click Detect markers again. Changing the mode clears the previous result until detection is run again.
- When the intended candidates are visible, click Next: Walk Setup.
Brief or incomplete movements do not qualify as marker holds. If APT reports no clear elevator-stick deflections, review the recording and try the opposite direction where appropriate; do not manufacture a marker to reach five.
Automatic detection selected the stronger positive-Ele sequence and found five complete holds. The candidates still require operator confirmation against the physical landmarks.
Walk 1 uses the original radio arrangement and establishes the fixed reference for every later walk.
- On Walk Setup & Landmarks, leave Create a new Walk 1 baseline selected.
- Optionally enter a Walk 1 label.
- Enter the required Baseline radio configuration, including the transmitter, receiver, antennas, placement and orientation.
- Map five distinct candidates to Landmark 1 through Landmark 5 (turnaround) in chronological order. Give every landmark a physical name.
- Exclude extra candidates instead of moving them out of their recorded order.
- Expand RF Settings (expandable; optional) and enter configured TX power, packet rate, RF mode/band and dynamic-power state where known.
- Click Save Walk 1.
A valid Walk 1 requires all five marker candidates. Five markers bound four moving sections: release of marker 1 to onset of marker 2, continuing through release of marker 4 to onset of marker 5. The stationary marker holds remain separate evidence.
Walk 1 maps each candidate to a named physical landmark in recorded order. Landmark 5 is the turnaround; the antenna arrangement and optional operator-entered RF settings document the baseline.
Repeat the same route, landmarks, turnaround and marker procedure. Keep RF settings and test conditions as consistent as practical, and describe the radio arrangement accurately rather than assuming that only one item changed.
- On CSV & Markers, choose the later walk's CSV and detect its candidates.
- Click Next: Walk Setup.
- Select Record an additional walk against a saved baseline under Workflow:.
- Choose the correct Saved Walk 1 baseline and review the displayed baseline reference.
- Enter the required Test radio configuration, describing antenna or placement changes as actually configured.
- Assign each detected candidate to the physical landmark it represents. A later walk may be saved with a missing marker, but leave it unassigned instead of assuming the remaining candidates are landmarks 1–4.
- Record RF settings where known, then click Save additional walk.
APT preserves a checksum-identified managed copy of each saved CSV. Saved metadata and inherited settings are operator records, not independent measurements of the physical installation. Settings inherited from Walk 1 do not verify the later walk's configuration.
- Click History & Comparison from the first page, or Next: History & Comparison from setup.
- Select a Walk 1 baseline:.
- Select one of its Comparison walk: entries.
- Click Compare selected walks. APT reconstructs the evidence from the saved, checksum-verified CSV copies in a background task.
- Review the Section comparison table.
- Open Plots to view the Walk 1 RF trace, the comparison-walk RF trace, and the Section RSSI and RQly P10 comparison.
- Open Details & metadata for saved landmark mappings, configurations and evidence provenance.
Version-1 baseline-only records remain readable, but APT cannot invent an associated walk or numerical comparison. Missing, corrupt, checksum-mismatched or incompatible saved evidence produces an explicit error instead of reconstructed RF values.
The four landmark-bounded sections produce eight rows: one baseline and one comparison row per section. Coverage, unavailable intervals and the inherited-settings qualification remain visible beside the RF statistics.
The third plot view compares both 1RSS P10 and RQly P10 across the four sections. The same Plots area also provides the individual Walk 1 and comparison-walk RF traces.
Each of the four sections has a row for Walk 1 and a row for the selected later walk. The table reports:
| Field | Meaning |
|---|---|
| 1RSS median | Median usable primary receiver RSSI observation, in dBm. |
| 1RSS P10 | Lower-tail 10th percentile of usable primary RSSI observations. More negative dBm is weaker. |
| RQly P10 | Lower-tail 10th percentile of usable receiver uplink link-quality observations, as a percentage. |
| RSNR median | Median usable receiver-reported signal-to-noise ratio, in dB. |
| Usable coverage | Eligible RSSI rows and their portion of observed section time. It is not proof of independent RF refreshes or continuous receiver reception. |
| Longest unavailable | Longest interval in the section without usable RF telemetry. |
| Evidence status | Whether section evidence is observed, incomplete, unavailable or not like-for-like. |
The individual-walk plots show RF values over transmitter-local time, marker holds and telemetry gaps. The section comparison plot shows Walk 1 and the selected walk for both 1RSS P10 and RQly P10. Unavailable points are omitted; APT does not draw them as zero or interpolate across missing sections.
The statistics summarize eligible values logged during landmark-bounded sections. Repeated values may be held rather than independent receiver updates. The sections represent the physical route between landmarks and are not assumed to have equal length.
Missing or zero-filled telemetry is unavailable evidence, not measured poor signal and not proof of an aircraft failsafe. A missing landmark makes each adjoining section incomplete. APT does not automatically reassign candidates or infer the absent boundary.
1RSS, RQly and RSNR are receiver-reported uplink metrics returned through transmitter telemetry. Reported transmitter power and RF mode are context, not measured radiated power or verified packet rate. Coverage does not prove continuous receiver reception.
Range-Walk Comparison does not declare an antenna winner, calculate an exact range limit or RF margin, or combine transmitter CSV measurements with aircraft BIN failsafe evidence. Route, installation, antenna orientation, surroundings and RF settings all affect comparability; interpret the numerical differences alongside the saved setup notes.
- Back to the Wiki Home
- Radio Link — inspect aircraft-side failsafe response from a BIN, optionally enriched with EdgeTX evidence.
- Range-Walk in-app Help source
- Range-Walk glossary
- Range-Walk Comparison Test Procedure
- APT project README
Getting started
Battery & packs
Flight analysis
Radio & diagnostics
Reference



