Rigwright v0.1.30

What's Changed

• Validate IC-756PROII hardware support by @nicksbar in #47

Full Changelog: v0.1.29...v0.1.30

Rigwright v0.1.29

What's Changed

Fixed

• Make SH filter-width set and answer layouts model-owned. FT-991A uses
  one fixed selector before the two-digit width index (SH001; for index 1);
  FT-710, FTDX10, and FTDX101D/MP retain their additional reserved field
  (SH0001;). Correct FT-991A readback to accept SH012; for index 12.
• Validate the profiled selector/reserved prefix when decoding width answers.

Tests and evidence

• Check exact read/write frames for all five modern Yaesu models, malformed
  FT-991A answers, and frequency polling after a width read. Command layouts
  were checked against the official CAT manuals.
• Investigated a QSONaut 0.4.0 report where FT-991A CAT polling failed after
  applying an FT8 preset. The malformed write is confirmed in software;
  physical-radio confirmation of the full timeout sequence remains pending.
• This release corrects CAT framing. Application preset bandwidth selection
  and model/mode-specific bandwidth tables need a separate audit; width index
  1 is not a universal digital-mode bandwidth preset.

Full Changelog: v0.1.28...v0.1.29

Rigwright v0.1.28

What's Changed

Added

• Add independent CI-V profiles for IC-756PRO, IC-756PROII, and IC-756PROIII,
  including their documented addresses, legacy mode commands, tuning steps,
  frequency ranges, controls, and model-specific meter surfaces.
• Add searchable Markdown extractions of all three instruction manuals and
  record their source PDFs, page counts, extraction tool, and the IC-756PROII
  hardware-validation target.
• Add separate Yaesu FT-1000 and FT-1000D legacy CAT profiles under the
  profile-owned src/yaesu/ft1000/ package, including documented 8N2/4800
  serial settings, five-byte commands, status-update decoding, split, mode,
  frequency, and PTT support.
• Add the interactive probe_wizard example for serial-device selection,
  bounded read-only identification, explicit model override, and opt-in
  minimum-power PTT validation with de-key and RF-power restoration.
• Expand probe_wizard with a file-backed HAL diagnostic that records
  advertised controls, meters, optional surfaces, timings, PASS/FAIL/SKIP
  results, and driver error details; safe same-value write round-trips are
  available only through explicit --exercise-writes.
• Improve CI-V discovery by scanning documented model addresses and baud
  rates, retaining the detected endpoint, and rejecting responses that do not
  contain both a parsed frequency and mode.
• Make diagnostic optional-surface results mode-aware for the IC-7300, so
  documented Data-mode limitations and unimplemented HAL methods are reported
  as skips instead of misleading driver failures.

Deliberate limitations

• The profiles are framework support; physical IC-756PROII validation remains
  pending and no hardware-validation claim is made yet.
• FT-1000/FT-1000D support is framework-level pending physical validation;
  Digimode 4 is an external serial/level interface and is not modeled as a
  separate radio protocol.

Full Changelog: v0.1.27...v0.1.28

Rigwright v0.1.27

What's Changed

• Add Kenwood TM-V71A and TM-D710 profiles by @nicksbar in #44

Full Changelog: v0.1.26...v0.1.27

v0.1.26

What's Changed

Release readiness

• Raise the aggregate executable-line coverage gate to 90% and promote the
  Icom CI-V, Kenwood CAT, and covered profile gates to 90%.
• Add manual-backed regression coverage for native Icom CI-V, Kenwood CAT,
  and model-profile command behavior.

Tests

• Expand RadioSession public-trait forwarding coverage for scope, repeater,
  RIT/XIT, memory, DTMF, tuner, raw protocol, meters, and capability-gated
  operations.
• Make probe-log temporary-file fixtures safe under parallel test and coverage
  execution.
• Add an aggregate 87% CI coverage floor with a documented 90%+ project target,
  and refresh the README coverage snapshot.

Full Changelog: v0.1.25...v0.1.26

Rigwright v0.1.25

What's Changed

• Fix FT-991A mode reads with IF status by @nicksbar in #42

Full Changelog: v0.1.24...v0.1.25

Rigwright v0.1.24

What's Changed

• fix: avoid FT-991A VS query in 0.1.24 by @nicksbar in #41

Full Changelog: v0.1.23...v0.1.24

Rigwright v0.1.23

Added

• Publish a profile-generated support/evidence contract with JSON and
  release-preparation Markdown output, explicitly separating cataloged,
  software-tested, and hardware-tested status.
• Add sanitized probe-report output for shareable diagnostics and document the
  release-preparation workflow for refreshing the generated support matrix.

Removed

• Remove the obsolete AsciiCatRadio compatibility driver and its
  AsciiCatFlavor selector. Use the model-aware YaesuCatRadio or
  KenwoodCatRadio drivers (or open_model) instead; the shared
  protocol::ascii_cat framing module remains available to those native
  drivers.

Fixed

• Preserve structured RadioSession/HAL errors through async Radio methods;
  callers can now downcast anyhow failures to HalError/SessionError
  instead of parsing error strings.
• Bound radio and session event subscriber queues, coalescing or evicting
  telemetry before critical session events and exposing dropped-event counts.
• Bound pending Icom CI-V response data to 4096 bytes, resynchronize after
  noisy oversized input, and expose pending-buffer overflow metrics.
• Make the PTT safety watchdog fail safe: emergency PTT-off now retries a
  bounded number of times, preserves an active PTT observation when shutdown
  cannot be confirmed, enters Degraded, and emits a distinct failure event.
• Expose Icom USB/native connection baud choices to clients. Models such as
  the IC-7300 now offer 38,400, 57,600, and 115,200 baud without changing the
  narrower physical REMOTE/CI-V port metadata.
• Preserve write-only power switching in the model capability metadata so
  QSONaut can send the documented CI-V power command for Icom radios.

Full Changelog: v0.1.22...v0.1.23

Rigwright v0.1.22

Added

• Complete profile-owned capability and meter metadata for Yaesu, Kenwood,
  and Elecraft radios, keeping shared protocol engines model-agnostic.
• Add profile-driven Elecraft support for K2, KX2, KX3, K3, K3S, K4, and KH1,
  including model-specific tuning, options, notch, memory, and control rules.
• Add manual-backed Kenwood memory codecs, model-specific memory selection,
  and conservative generic-profile behavior for unsupported features.
• Add release coverage tests for Icom scope configuration and USB discovery,
  Elecraft profile boundaries, and the generic HAL contract.

Fixed

• Keep configured-radio startup probing inside the driver boundary, using
  model verification for modern Yaesu CAT radios whose optional VFO-selector
  query may be rejected even when CAT is healthy.
• Move vendor and model quirks out of generic drivers and into explicit radio
  profiles, preventing unsupported capabilities from being advertised

Full Changelog: v0.1.21...v0.1.22

Rigwright v0.1.21

What's Changed

• Fixes IC-7300 scope commands

• Release Rigwright 0.1.21 by @nicksbar in #26

Full Changelog: v0.1.20...v0.1.21