TinyG Boot Loader

Huge thanks to Kevin Osborn who got this working

Updating TinyG Firmware using the Boot Loader

Step1: To update the TinyG firmware run avrdude from a directory that has the tinyg.hex file you want to load. Here's an example command line from Windows:
avrdude -p x192a3 -c avr109 -b 115200 -P COM19 -U flash:w:tinyg.hex

You will need to enter the USB port you are actually using.
Use the Avrdude distributed with the Arduino - it's pretty up to date.

Flashing the Boot Loader onto the Xmega Chip

The following instructions explain how to flash the boot loader using Atmel Studio6. AVRStudio4 is similar, as would be command-line operation. These instructions use the xboot-boot.hex file already in the project. If you want to compile go to the next section.

Step 1. Get the right programmer. The xmega requires PDI programming. Use the Atmel AVRISP mkii or some other programmer that supports PDI programming. Plug the programmer into TinyG and apply power to TinyG.

Step 2. Bring up Studio6 and the device programming panel. Look under Tools/Device Programming

• In the programming panel verify Tool is AVRISP mkii, the device is ATxmega192A3 and the interface is PDI. Hit Apply. You should see the Device signature and voltage field populate. Voltage should be 3.2v or thereabouts.

Step 3. Set the fuses. Go to Fuses and set the following

• set BOOTRST to BOOTLDR

Other values should be left alone. These are:

• JTAGUSERID = 0xFF
• WDWP = 8clk
• WDP = 8clk
• DVSDON = (unchecked)
• BODPD = disabled
• RSTDISBL = (unchecked) Don't check this - you will brick the board
• SUT = 0ms
• WDLOCK = (unchecked)
• JTAGEN = (CHECKED) Don't uncheck this, you will brick the board
• BODACT = disabled
• EESAVE = (unchecked)
• BODLVL = 1v6
• Leave the lock bits alone for now

Step 4. Use xboot-boot.hex for programming. Do not use xboot.hex as it's org'ed in the wrong place (0 instead of 0x30000)

Compiling the Boot Loader for TinyG

Use these instructions if you want to change the xboot-boot.hex file. If all you want to do is flash it onto TinyG see the previous section.

Step 1. The command line you need is:
make conf\x192a3.conf.mk

But beware - it only works in windows. Use cmd and navigate to the (lower) xboot directory something like: Z:\Username\Projects\...\TinyG\xboot\xboot\make conf\x192a3.conf.mk

It enters an infinite loop in Linux and generates this error iin OSX

macintosh-3:xboot your-user-dir$ make conf\x192a3.conf.mk
.dep/fifo.o.d:1: *** multiple target patterns.  Stop.
macintosh-3:xboot your-user-dir$

We have not diagnosed or fixed this yet.

Developer Notes

The boot loader is Alex Forencich's xboot which can be found in the xboot directory in the main TinyG git tree. This xboot has the settings and modifications for use on TinyG. (You can safely ignore the xmega_boot directory.)

Getting Xboot to work in Native Windows

Bring up a cmd window and navigate to the working directory. Run the command:

make conf/x192a3.conf.mk

Getting Xboot to work in Atmel Studio6

THESE NOTES ARE IN PROCESS AND ARE NOT YET COMPLETE

The xboot project has been set up under Atmel Studio6 (Windows only). The project files are the xboot.atsln and xboot.cproj files in the github TinyG/support dir. Move these to your project directory then click on xboot.atsln to start the project up.

This project uses the Studio6 auto-generated makefile in the Debug directory instead of the native Makefile in the working directory. This is so the debugger can support symbolic debugging. Some things had to happen for this to work.

1. You must generate config.h by running make conf/x192a3.conf.mk. If the conf file changes you must run this again to refresh config.h
2. Setup the xboot project properties:

add 'F_CPU=32000000' to symbols
change optimization to -Os if it's not already there