Porting firmware for TS0201 _TZ3000_f2bw0b6k (Moes ZSS-S01-TH-C-MS)

[MichelCHAVOT]

Hi, requesting support for another TS0201 variant.

Device

Product: Moes ZSS-S01-TH-C-MS (Temperature & Humidity Sensor)
Zigbee model: TS0201
Zigbee manufacturer: _TZ3000_f2bw0b6k
Already recognized by Zigbee2MQTT and ZHA, but default reporting is not configurable — reports only trigger on a ~0.3°C change, no way to set min/max interval via the standard Reporting tab (matches the general TS0201 Tuya-firmware limitation).

Hardware

Radio module: labeled "ZTU" on the module itself, P/N: 2.01.03.00300
Temperature/humidity sensing element is on a separate small PCB connected via flex cable, silkscreened "RH_V1.2_2309" (likely rev 1.2, dated 2023-09)
Button (SW1) and LED (near "U1") are on the main board, not on the ZTU module — so GPIO mapping for button/LED is probably board-specific and may need adjusting (similar to what was needed in #124 for _TZ3000_bguser20)
Main board also has passive components C1/C3/C5, R1/R3/R4/R5 around the button/LED area — nothing unusual noted


[29/08/2026 18:32:10] z2m: Interviewing 'T° Séjour 1 New'
[29/08/2026 18:32:10] z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/bridge/event', payload '{"data":{"friendly_name":"T° Séjour 1 New","ieee_address":"0xa4c138f36016737f","status":"started"},"type":"device_interview"}'
[29/08/2026 18:32:20] z2m: Successfully interviewed 'T° Séjour 1 New'
[29/08/2026 18:32:20] z2m:mqtt: MQTT publish: topic 'zigbee2mqtt/bridge/event', payload '{"data":{"definition":{"description":"Temperature and humidity sensor","exposes":[{"access":1,"category":"diagnostic","description":"Remaining battery in %, can take up to 24 hours before reported","label":"Battery","name":"battery","property":"battery","type":"numeric","unit":"%","value_max":100,"value_min":0},{"access":1,"description":"Measured temperature value","label":"Temperature","name":"temperature","property":"temperature","type":"numeric","unit":"°C"},{"access":1,"description":"Measured relative humidity","label":"Humidity","name":"humidity","property":"humidity","type":"numeric","unit":"%"},{"access":1,"category":"diagnostic","description":"Voltage of the battery in millivolts","label":"Voltage","name":"voltage","property":"voltage","type":"numeric","unit":"mV"},{"access":1,"category":"diagnostic","description":"Link quality (signal strength)","label":"Linkquality","name":"linkquality","property":"linkquality","type":"numeric","unit":"lqi","value_max":255,"value_min":0}],"model":"ZSS-S01-TH","options":[{"access":2,"description":"Calibrates the temperature value (absolute offset), takes into effect on next report of device.","label":"Temperature calibration","name":"temperature_calibration","property":"temperature_calibration","type":"numeric","value_step":0.1},{"access":2,"description":"Number of digits after decimal point for temperature, takes into effect on next report of device. This option can only decrease the precision, not increase it.","label":"Temperature precision","name":"temperature_precision","property":"temperature_precision","type":"numeric","value_max":3,"value_min":0},{"access":2,"description":"Calibrates the humidity value (absolute offset), takes into effect on next report of device.","label":"Humidity calibration","name":"humidity_calibration","property":"humidity_calibration","type":"numeric","value_step":0.1},{"access":2,"description":"Number of digits after decimal point for humidity, takes into effect on next report of device. This option can only decrease the precision, not increase it.","label":"Humidity precision","name":"humidity_precision","property":"humidity_precision","type":"numeric","value_max":3,"value_min":0}],"source":"native","supports_ota":true,"vendor":"Moes","version":"0.0.0"},"friendly_name":"T° Séjour 1 New","ieee_address":"0xa4c138f36016737f","status":"successful","supported":true},"type":"device_interview"}'

Happy to test a build, report back GPIO issues, or take more photos/measurements if useful. Let me know what else would help.