docs: add Radxa 25W PoE+ HAT for X4 documentation and update PoE HAT … #1284
There are no files selected for viewing
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,89 @@ | ||
| --- | ||
| sidebar_label: "Radxa 25W PoE+ HAT for X4" | ||
| sidebar_position: 1 | ||
| --- | ||
|
|
||
| # 瑞莎 25W PoE+ HAT for X4 | ||
|
|
||
| Radxa 25W PoE+ HAT for X4 专为 Radxa X4 设计，可为其提供以太网供电（PoE+）功能，支持通过网线同时实现数据通信和电力传输。 | ||
|
|
||
| :::info | ||
| 需搭配使用兼容的以太网供电设备。 | ||
| ::: | ||
|
|
||
|  | ||
|
|
||
| ## 兼容性 | ||
|
|
||
| Radxa 25W PoE+ HAT for X4 专为以下产品设计： | ||
|
|
||
| - Radxa X4 | ||
| - Radxa Dragon Q6A | ||
|
|
||
| ## 功能 | ||
|
|
||
| - 符合 IEEE 802.3at 标准 | ||
| - 宽输入电压范围：37V ～ 57V | ||
| - 输出：5V/4.8A、12V/2.1A | ||
| - 仅连接 5V 负载时，PoE 输出高达 5V DC / 4.8A | ||
| - 仅连接 12V 负载时，PoE 输出高达 12V DC / 2.1A | ||
| - 配备可编程温度传感器 | ||
| - 配备 1.45CFM 的可定制冷却风扇，用于处理器冷却 | ||
| - 尺寸：20 x 20 毫米 | ||
| - 转速：15000 ± 15%RPM | ||
| - 12V 电源输出 | ||
| - 1x 2-Pin 3.5 mm 间距可插拔接线端子 | ||
| - 工作温度范围：0°C 至 +50°C | ||
|
|
||
| ## 接口说明 | ||
|
|
||
| - ① : 12V DC 输出 | ||
| - 1x 2-Pin 3.5 mm 间距可插拔接线端子 | ||
| - ② : PoE 接口 | ||
| - ③ : 40-Pin GPIO 接口 | ||
|
|
||
|  | ||
|
|
||
| ## 使用方法 | ||
|
|
||
| 瑞莎 25W PoE+ HAT for X4 的包装清单如下： | ||
|
|
||
| - 瑞莎 25W PoE+ HAT for X4 | ||
| - 4x M2.5x9+6 铜柱 | ||
| - 4x M2.5x4+6 铜柱 | ||
| - 4x M2.5x5 铜柱 | ||
|
|
||
| :::tip | ||
| 如果要与瑞莎 X4 散热器一起使用，只需将 M2.5x9 + 6 铜柱替换为 M2.5x9 + 3 铜柱。 | ||
| ::: | ||
|
|
||
| ### 安装步骤 | ||
|
|
||
| 1. 将四根 M2.5x9+6 铜柱或 M2.5x9+3 铜柱（如果使用散热器）穿过 SBC 的四个定位孔，并从底部固定。 | ||
|
|
||
| 2. 将瑞莎 25W PoE+ HAT for X4 与 PoE 接口和 40 针接口对齐，并确保 12V 供电接口对齐，小心插入，确保穿过四个铜柱。 | ||
|
|
||
| 3. 在瑞莎 25W PoE+ HAT for X4 的顶部，使用 M2.5x4+6 铜柱或 M2.5x5 铜柱固定到位。 | ||
|
|
||
| 4. 连接以太网线到 PoE 接口，确保另一端连接到支持 PoE+ 的交换机。 | ||
|
|
||
| <Tabs queryString="model"> | ||
| <TabItem value="x4" label="Radxa X4"> | ||
|
|
||
|  | ||
|
|
||
| </TabItem> | ||
| <TabItem value="q6a" label="Dragon Q6A"> | ||
|
|
||
|  | ||
|
|
||
| </TabItem> | ||
|
|
||
| </Tabs> | ||
|
|
||
| ## 资料下载 | ||
|
|
||
| ### 产品资料 | ||
|
|
||
| - [原理图 V1.2](https://dl.radxa.com/accessories/25w-poe/radxa_25w_poe_plus_hat_v1.2_schematic.pdf) | ||
| - [3D 文件](https://dl.radxa.com/accessories/25w-poep-hat-for-x4/radxa_25w_poe+_hat_for_x4_v1.2_3d_stp_20241127.zip) | ||
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change | ||||
|---|---|---|---|---|---|---|
| @@ -0,0 +1,89 @@ | ||||||
| --- | ||||||
| sidebar_label: "Radxa 25W PoE+ HAT for X4" | ||||||
| sidebar_position: 1 | ||||||
| --- | ||||||
|
|
||||||
| # Radxa 25W PoE+ HAT for X4 | ||||||
|
|
||||||
| The Radxa 25W PoE+ HAT for X4 is specifically designed for Radxa X4, providing Power over Ethernet (PoE+) functionality that enables both data communication and power transmission through a single network cable. | ||||||
|
|
||||||
| :::info | ||||||
| Requires the use of a compatible Power over Ethernet device. | ||||||
| ::: | ||||||
|
|
||||||
|  | ||||||
|
|
||||||
| ## Compatibility | ||||||
|
|
||||||
| Radxa 25W PoE+ HAT for X4 is designed for the following products: | ||||||
|
|
||||||
| - Radxa X4 | ||||||
| - Radxa Dragon Q6A | ||||||
|
|
||||||
| ## Features | ||||||
|
|
||||||
| - Compliant with IEEE 802.3at standards | ||||||
| - Wide input voltage range: 37V ~ 57V | ||||||
| - Output: 5V/4.8A, 12V/2.1A | ||||||
| - When only a 5V load is connected, the PoE output is up to 5V DC / 4.8A | ||||||
| - When only a 12V load is connected, the PoE output is up to 12V DC / 2.1A | ||||||
| - Features a programmable temperature sensor | ||||||
| - Equipped with a customizable Cooling Fan delivering 1.45CFM for processor cooling | ||||||
| - Size: 20 x 20 mm | ||||||
| - Speed: 15000 ± 15%RPM | ||||||
| - 12V DC Output | ||||||
| - 1x 2-Pin 3.5mm Plug-in PCB Terminal Block | ||||||
| - Operating Temperature Range: 0°C to +50°C | ||||||
|
|
||||||
| ## Interface | ||||||
|
|
||||||
| - ①: 12V DC Output | ||||||
| - 1x 2-Pin 3.5mm Plug-in PCB Terminal Block | ||||||
| - ②: PoE Header | ||||||
| - ③: 40-Pin GPIO Header | ||||||
|
|
||||||
|  | ||||||
|
|
||||||
| ## Usage | ||||||
|
|
||||||
| The package list of Radxa 25W PoE+ HAT for X4 is as follows: | ||||||
|
|
||||||
| - Radxa 25W PoE+ HAT for X4 | ||||||
| - 4x M2.5x9+6 Copper Pillars | ||||||
| - 4x M2.5x4+6 Copper Pillars | ||||||
| - 4x M2.5x5 Copper Pillars | ||||||
|
|
||||||
| :::tip | ||||||
| If you want to use it together with Radxa Heatsink for X4, then you only need to replace the M2.5x9 + 6 copper pillar with the M2.5x9 + 3 copper pillar. | ||||||
| ::: | ||||||
|
|
||||||
| ### Installation Steps | ||||||
|
|
||||||
| 1. Pass four M2.5x9+6 Copper Pillars or M2.5x9+3 Copper Pillars (if using heatsink) through the four positioning holes of the SBC, and secure them from the bottom. | ||||||
|
|
||||||
| 2. Align the Radxa 25W PoE+ HAT for X4 with the PoE interface and the 40-Pin interface, ensuring the 12V power interface is aligned, and insert it carefully, ensuring that it passes through the four Copper Pillars. | ||||||
|
|
||||||
| 3. On top of the Radxa 25W PoE+ HAT for X4, use M2.5x4+6 Copper Pillars or M2.5x5 Copper Pillars to secure it in place. | ||||||
|
|
||||||
| 4. Connect an Ethernet cable to the PoE interface, ensuring the other end is connected to a PoE+ compatible switch. | ||||||
|
|
||||||
| <Tabs queryString="model"> | ||||||
| <TabItem value="x4" label="Radxa X4"> | ||||||
|
|
||||||
|  | ||||||
|
|
||||||
| </TabItem> | ||||||
| <TabItem value="q6a" label="Dragon Q6A"> | ||||||
|
|
||||||
|  | ||||||
|
|
||||||
| </TabItem> | ||||||
|
|
||||||
| </Tabs> | ||||||
|
|
||||||
| ## Downloads | ||||||
|
|
||||||
| ### Product Information | ||||||
|
|
||||||
| - [Schematic V1.2](https://dl.radxa.com/accessories/25w-poe/radxa_25w_poe_plus_hat_v1.2_schematic.pdf) | ||||||
|
Contributor
There was a problem hiding this comment. There's a typo in the URL for the 3D Drawings download link. It contains 'poep-hat' instead of 'poe-hat', which might lead to a broken link.
Suggested change
|
||||||
| - [3D Drawings](https://dl.radxa.com/accessories/25w-poep-hat-for-x4/radxa_25w_poe+_hat_for_x4_v1.2_3d_stp_20241127.zip) | ||||||
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
There was a problem hiding this comment.
Choose a reason for hiding this comment
The reason will be displayed to describe this comment to others. Learn more.
There appears to be a typo in the 3D files download URL. It currently says '25w-poep-hat-for-x4' but should likely be '25w-poe-hat-for-x4' or '25w-poe-plus-hat-for-x4'.