-
Notifications
You must be signed in to change notification settings - Fork 0
Hardware
First we have to talk about the hardware aspects of the project to fully understand the software side. This section explains the concept of an electric longboard and the function of its mechanical components. A separate chapter is dedicated to the wiring and composition of the microcontroller, as it is a hardware component, but of course its construction depends on the program running on it.
When creating a small electric-powered vehicle, such as an electric longboard, there are a few things to consider before buying the components. From the shape of the board itself to the size of the batteries, these are the topics, which will be discussed in this subsection, including all the trade-offs between choosing one configuration over another.
At the end of the page in the section "External links" I listed different online calculators and guides for finding suitable components for the build.
As with the previous prototype, I decided not to build my own longboard, but rather buy a suitable one. It was mostly because building the board itself was not the goal of my project, but that does not mean, you should not care about the parts you buy.
APEX SERPENTINE MK II is a flexible half bamboo half maple flex 1 deck. It is a concave deck with raised middle (camber deck). Its shape allows for big enough clearance for the components to be mounted to the bottom.
Altera trucks 180mm came with the deck. It would be ideal to have a pair with square axle, which would allow for easier installation of the motor mount, but instead I rather designed a mount that fits around the round axle nicely.
Orangatang Kegel 83A are 80mm wheels with a plastic core. The core features holes which snugly fit a M4 screw, easing the mounting of a 3D printed pulley. The size of the wheels is also an important factor regarding riding speed. The greater the diameter of the wheel the faster it spins at a given RPM, compared to a smaller-diameter wheel.
The prototype is a single-wheel drive system. The advantages of such a configuration are the ability to fit a larger, more powerful BLDC motor under the deck and cost efficiency, but the downsides are less traction when accelerating and more stress on the drive belt. Another alternative would be a hub motor, which is already embedded in the wheel itself and consequently does not need a drivetrain, but such motors are fairly expensive and less powerful.
Turnigy Aerodrive SK3 - 6374-192KV Brushless Outrunner Motor has 4kW of power and as it is a relatively low kv motor that means it can create a lot of torque when accelerating or driving up the slope. It is suitable for 10 to 12S LiPo battery and handles up to 80A of current.
The custom made aluminium mount is designed to hold the motor on the trucks. It is bulky and heavy since it had to be made to withstand the forces the motor puts on the system when accelerating or breaking, while being mounted on a round axle, rather than a square one, which would prevent rotation of the mount.
The single-wheel drivetrain uses HTD5 pulleys and belt. It features 2.4 reduction ratio.
15t aluminium pulley was mounted to the motor shaft using a threaded pin which was coated with Loctite Threadlocker beforehand. It can fit up to 12mm wide drive belts.
I found a great 3D model of the 36t wheel pulley made for the wheels i chose on Thingiverse. I printed it from nylon as it must handle friction and the elements without loosing its shape. It can fit drive belts up to 12mm wide.
55t drive belt is 10mm wide, which ensures a good ratio between strength and friction. A wider belt would be more durable but it would introduce more friction in the system, and vice versa applies for a narrower belt.
Choosing the right electronic speed controller (ESC) might be the most important step. The first ESC, purposely build for electric skateboards was made by Benjamin Vedder and it was called the VESC. It was an open source project and Vedder's blueprints were the foundation for various iterations from other companies. The VESC has since been patented and companies are not allowed to use the same name, but the principles remain the same. I bought my "VESC" from Enertion. It is called "FOCBOX" and it allows for smooth acceleration and precise breaking, which are important, because on a skateboard there are no handlebars to lean on in case of a strong acceleration or deceleration. It features a Micro-USB connector, which allows it to connect it to the computer and program it via BLDC tool.
TODO
It is important to choose batteries with a relative high voltage to reduce the current flow. I also wanted to integrate the charging circuit to ease the operation of charging the battery pack.
The 10S 5000mAh battery pack was made from 2 ZIPPY Compact 5000mAh 5S 25C Lipo Packs connected in series. Their volume is small and with buying a prebuilt pack you avoid soldering the individual battery cells, which can be quite challenging without proper equipment.
To integrate a power delivery system which would allow for charging using a wall charger, a Battery Management System had to be implemented. The circuit also features a 40A overcurrent protection, which was not needed and was bypassed. The system charges using a 42V 5A wall charger and it does so in about an hour.
TODO:bms wiring scheme
I designed my own enclosure in Autodesk Fusion 360. It is otherwise a very simple enclosure, but its main property is its compactness. After 3D printing it with an SLA printer, I hand made the openings for the power button, charging port, lights port and motor wires.