bgp rib

Pre-Alpha. This page describes behavior that may change.

The main BGP RIB store and best-path selection engine.

Category

Storage.

Configuration

Load the plugin and bind it to peers.

plugin {
    internal rib { use bgp-rib }
}

bgp {
    peer upstream {
        connection { remote { ip 10.0.0.1; } }
        session    { asn { remote 65001; } }
        process rib { receive [ update state ]; send [ update ]; }
    }
}

receive [ update state ] lets the RIB see routes arriving and peer state changes. send [ update ] lets it send routes back out after best-path selection (when acting as a router) or forwarding (when paired with bgp-rs).

Behaviour

bgp-rib stores routes per prefix per family and runs RFC 4271 section 9.1.2 best-path selection when multiple paths exist for a prefix. N-way multipath is supported: when bgp/multipath is configured with maximum-paths and relax-as-path, multiple equal-cost paths are selected and installed. The output is fed to sysrib (unified Loc-RIB) for cross-protocol admin-distance selection and then to fib-kernel and/or fib-vpp for forwarding table installation. The best-path order is LOCAL_PREF, AS_PATH length, ORIGIN, MED (same neighbour AS only), eBGP over iBGP, IGP cost (not implemented), lowest router-id, lowest peer address.

When candidates tie under multipath selection, the winner and its equal-cost sibling next hops both go into the shared Loc-RIB, and the system RIB emits one ECMP group to the active FIB backend. A membership-only change, such as one equal-cost peer going away, updates the installed group without the winning peer having to change. show rib reports the primary next-hop plus an ecmp-paths array; the two together are the complete installed next-hop set.

The RIB uses a two-level ribInPool keyed by ProtocolID, enabling multi-source support. BGP peers and BMP-monitored peers store routes under separate ProtocolIDs, so best-path selection only iterates real BGP routes while BMP routes are visible through the looking glass without additional filtering.

Internally, the RIB uses BART (Binary Adaptive Radix Tree) storage with per-family NLRI split registry. Non-CIDR families (EVPN, FlowSpec, etc.) get an opaque-map backend. bestPathRecord is packed into uint64 with a shared cross-family interner for memory efficiency. The Loc-RIB shards by prefix hash and the peer-keyed map lock is split from the main RIB mutex to keep it off the hot path.

The plugin also handles the RIB half of Graceful Restart: holding stale routes during a peer restart, clearing them on EOR, and purging any that did not come back.

Compact ribOut storage

The per-peer Adj-RIB-Out (ribOut) stores a 16-byte entry per peer per route: a MsgID (8 B), an attribute pool handle (4 B), a stale level (1 B), and padding. The wire attribute bytes are deduplicated in a shared pool (pool.RibOut), so the same UPDATE sent to N peers stores one pool copy and N four-byte handles instead of N full attribute blobs. The full *Route is reconstructed on demand on cold paths only (replay, show, refresh) by parsing the wire bytes back out of the pool. Source-peer tracking uses a separate refcounted map with one entry per unique route, not per destination peer. See performance for the measured per-route numbers.

Route replay on reconnect

The plugin replays stored routes when a peer reconnects. A batch of fixes landed recently (three bugs in the sent-event path: dispatch routing by Direction instead of EventType, missing WireUpdate on sent events, and a format mismatch for text-codec routes). The sync is now event-driven rather than timer-driven, and the graceful-restart, LLGR, and refresh-on-reconnect test scenarios all pass reliably.

Metrics

Registered via ConfigureMetrics. Includes both route counts and attribute-pool statistics.

Metric	Type	Meaning
ze_rib_routes_in_total	gauge	Total Adj-RIB-In route count across all peers.
ze_rib_routes_out_total	gauge	Total Adj-RIB-Out route count across all peers.
ze_rib_routes_in{peer}	gauge	Adj-RIB-In route count per peer.
ze_rib_routes_out{peer}	gauge	Adj-RIB-Out route count per peer.
ze_rib_route_inserts_total{peer,family}	counter	Routes inserted into Adj-RIB-In.
ze_rib_route_withdrawals_total{peer,family}	counter	Routes withdrawn from Adj-RIB-In.
ze_attr_pool_intern_total{pool}	gauge	Total Intern() calls per attribute pool.
ze_attr_pool_dedup_hits_total{pool}	gauge	Intern() dedup hits per pool.
ze_attr_pool_slots_used{pool}	gauge	Active slots per pool.

See plugin metrics.

RPF lookup

The RIB supports Reverse Path Forwarding queries via longest-prefix-match on the sharded Loc-RIB. This is exposed as a CLI command for external multicast daemons (PIM-SM) to resolve upstream next-hops.

ze> show bgp rib rpf ipv4/multicast 10.0.1.5

The command is show bgp rib rpf <family> <source-addr>. It returns the best-path entry for the longest matching prefix, including next-hop, AS path, and origin peer.

Interactions

• bgp-gr depends on bgp-rib for the stale route handling.
• bgp-persist snapshots the RIB to disk.
• bgp-adj-rib-in feeds raw received updates into the RIB.
• sysrib consumes best-path change events from the RIB.

Source

main/internal/component/bgp/plugins/rib/