Skip to content

Bill of Materials

Jump to bottom
github-actions[bot] edited this page Mar 15, 2025 · 37 revisions

All parts (screws, magnets, etc) are Voron, and Voron Tap standards.

  1. Shuttle
  2. BackPlates
  3. Endstops
  4. Options
  5. Sexball Probe
  6. Affiliate Links

Shuttle

  • [3] 6x3mm magnets (N52 Highly recommended to counter the pull from the umbilicals)
  • [2] m3x6 BHCS (tap sensor)
  • [4] m3x6 BHCS head (mgn bolts) m3x12 if used with the shuttle keeper
  • [3] 4x6x6mm brass bushing (4mm id x 6mm od x 6mm tall)
  • [2] m3x40 SHCS (Optional: to stiffen the shuttle, Fully threaded, no shoulder)

Backplates

x1 per toolhead

All Tools

Note: heatsets on the SB version in from the opposite side as the Voron instructions, slightly longer screws on the CW2 attachment may be required

  • [4] m3 heat inserts
  • [3] Ø4x12mm ssRod (dowel pin) with a rounded end (if it has female threads on the back it will be listed as an M3, but make sure the pin is 4mm OD, that is what is important. We recommend the threaded pins for better fixing)
  • [1] 6x3mm magnet (N52 Highly recommended to counter the pull from the umbilicals. Note that most magnets not from a reputable source may say N52 but aren't actually. Recommend one of the two links below.)
  • [2] m3x6 or m3x8 FHCS (Flat head countersunk screw, MUST BE MAGNETIC. no stainless, as per TAP)
  • [1] OptoTap (only the sensor PCB is required)
  • [1] m3x8 BHCS (optional in v1.1)

The list bellow is in addition to the Stealthburner BOM above.

Dragonburner/Rapidburner/Yavoth

  • [1] m3x12 BHCS (optional to keep spacer in place)
  • [2] m3x35 SHCS
  • [2] m3 heat inserts
  • [2] m3x8 BHCS (optional in v1.1)

Note: Dragonburner extended mount is required depending on extruder

Archetype Blackbird

  • [1] m3x12 BHCS (to hold the sherpa mount in place)
  • [2] m3 heat inserts
  • [2] m3x8 BHCS (optional in v1.1)

Xol

  • [2] m3x6 BHCS (backplate lower mounting screws. m3x8 will be too long)
  • [2] m3x20 BHCS (backplate upper mounting screws)
  • [2] m3x8 BHCS (extruder mount to backplate)
  • [2] m3x6 FHCS magnetic (preload screws. m3x8 will be too long)
  • You will not be able to use stock 2.4 Z joints with Xol or A4T.
  • Replacement of your Z joints with something with a lower profile such as hartk123's GE5C Z Joint or Ellis'Short Z Joints is necessary to avoid bottoming out your Z carriage on the deck panel when using Xol or A4T.

A4T

  • [2] m3x45 SHCS magnetic (backplate lower mounting screws)
  • [2] m3x12 BHCS / SHCS (backplate upper mounting screws)
  • [2] m3x6 FHCS magnetic (preload screws. m3x8 will be too long)
  • You will not be able to use stock 2.4 Z joints with Xol or A4T. See links in Xol section above for links to alternative suggestions.

Endstops

Optional

  • [1] m3x6 BHCS
  • [1] m3 heat insert
  • [1] 6x3mm magnet (Hall Effect Sensor ONLY, Voron spec)

Options

You will likely need help with belts, make sure to decide on if you will use the shuttle keeper or use the belt helper. And print the required parts and make sure to have the addition bill of materials for them.

Sexball probe

Sexball probe

Image By asoli

Calibration probe option that just replaces the shaft on a sexbolt.

NOTE: For micron M5x25mm Pin is tall enough

NOTE: Only use the hartk style bodys with the sleeves, knockoffs have too much slop.

Sexball probe types

Image by BT123

Affiliate Links

Parts Link 1 Link 2 Link 3
Bushing AliExpress US Amazon UK Amazon
Pin AliExpress US Amazon UK Amazon
N52 Magnets US KB-3D UK Printy Please

Due to QC issues, this is an Alternative bush which has also been tested and works fine.

Alternatively you can purchase check on our official vendors list

Clone this wiki locally