Skip to content

Releases

B3 Organ

Choose a tag to compare

@R-Jeb R-Jeb released this 17 Nov 14:48
bc00345

A logo, an install page and two small fixes; the organ sounds as in 0.5. What is new since 0.5:

  • A logo after switching on: a row of drawbars over the name. It comes back as a screen saver after a minute without a knob, a
    button or a key. The first knob or button only brings back the upper manual's page (it changes nothing); a key plays at once.
  • The install shows its progress on the FM-1: the logo with a bar under it while it waits (UPDATE MODE), while it writes
    (WRITING 57 %, DO NOT SWITCH OFF) and if it fails (UPDATE FAILED, INSTALL AGAIN). After 100 % the FM-1 restarts.
  • Install from the browser: r-jeb.github.io/setBfree-fm1 in Chrome or Edge, the FM-1 on USB,
    with the four pages and every control explained. It also takes the FM-1 back to the official firmware.
  • The lower and pedal pages show the footage numbers under their drawbars again (16, 5 1/3, 8 ...); they were cut off on the FM-1.
  • The pedal page no longer shows the load: page 4 (test values) has it, with the MIDI messages.
  • A first start without saved settings has setBfree's drive 12 (it was 3, from the old character steps).

Your settings and your own programs 112 to 127 stay through the update.

Install: on the page above, or b3organ-0.5.1.fwsc with the FM-1 Firmware Hub or the README's other ways. 0.5 stays available under Releases.
Please report what sounds different from setBfree.

B3 ORGAN

Choose a tag to compare

@R-Jeb R-Jeb released this 16 Nov 16:32
a3643b5

A web editor that reads and writes the FM-1, your own programs, and the first of setBfree's extended parameters.
What is new since 0.4:

  • The web editor: r-jeb.github.io/setBfree-fm1/editor, in Chrome or Edge, the FM-1 on
    USB. Allow MIDI and SysEx when the browser asks. It reads the FM-1's sound when it connects (drawbars of all three manuals, vibrato,
    percussion, Leslie, overdrive, reverb, swell, the program and the firmware's version) and sends every change at once. Five pages:
    Manuals (with the presets beside the pedal), Overdrive & Leslie, Tone & Reverb, Backup and a MIDI monitor.
  • Your own programs 112 to 127. The editor stores the FM-1's whole sound in one of them, with a name of up to 12 letters: the drawbars
    of all three manuals, vibrato, percussion, Leslie, overdrive (on, drive, character) and reverb. They are in their own flash sector and stay
    through power off; save a backup before you flash another firmware. The PRESETS knob steps through them after setBfree's programs, program change 111 to
    126 selects them, and the screen shows their names. setBfree's programs still change only what they name; yours set everything.
  • Overdrive character. setBfree's overdrive.character (0 to 127, 16 as before) next to the drive: in the editor, or NRPN 1/0.
  • Leslie, extended parameters: the horn's and the drum's slow and fast speeds and how fast each speeds up and slows down
    (setBfree's whirl.*). setBfree's values are the default and a button brings them back. They are hidden until you switch them on.
  • Tuning 430 to 450 Hz in steps of 1 Hz (440 by default), and the key click level (setBfree's osc.attack.click.level, 50 %), the
    click under the extended parameters.
  • Backup: the editor saves your programs and the extended parameters as a file and puts them back, on this FM-1 or another one.
  • The settings of 0.4 are kept when you update. With setBfree's values the organ sounds bit for bit as 0.4.

For MIDI: the new values go as NRPN (CC 99 / 98, data CC 6 and, for the 14-bit ones, CC 38), the editor's SysEx starts F0 7D 42 33;
README_ORGAN.md has the list.

B3 ORGAN v0.4

Choose a tag to compare

@R-Jeb R-Jeb released this 14 Nov 07:40
89e99a2

Two processor cores, a drive control for the overdrive, a limiter against clipping, a quieter Leslie and a DIN MIDI input that does not hang.
What is new since 0.3:

  • Two processor cores. The tonewheels are split in two halves (even and odd wheels); the second core of the FM-1 renders one half, the first core the other, then the preamp, reverb and Leslie. The two halves add up to exactly what one core gave (checked bit for bit on every build), so the sound and the latency are the same, but chords with many notes, with overdrive, reverb and Leslie on, no longer run out of time. Measured on an FM-1 with a loaded patch (4 keys on upper and lower, percussion, chorus, Leslie fast, reverb 4): organ 3600 to 3800 us before, about 2000 us now; the whole block about 5800 to 6200 us before (limit 5800), about 4000 us now (4400 us with the overdrive on). If the second core does not answer at start, the firmware plays on one core as before (screen 4 shows C1 instead of C2).
  • Overdrive with a drive control. KNOB 3 and CC 93 are now a drive (0 to 16): setBfree's overdrive.inputgain in steps of 1.5 dB, 12 is its default. The character (overdrive.character) is fixed at 16; the nine character steps of 0.3 are gone. The output follows the drive, so overdrive on and off are about equally loud. The character is to become adjustable in the web editor later.
  • Limiter. The limiter keeps the peaks below full scale: on the wheels' sum with the overdrive off, and on the output after reverb and Leslie. It works by gain, per block with a short attack and a slow release, not as a static clip: a sine over full scale has a distortion of -62 dB (a static soft clip had -29 dB). Many keys with the swell pedal at 60 to 100 % no longer clip, with or without overdrive.
  • Leslie without the noise. The delays of the horn and the drum are now in 1/256 sample (they were 1/16): the coarse steps made a broadband noise at 6 to 12 kHz while the horn turns (16 dB less at slow). It is the full setBfree model, as before.
  • DIN MIDI input (TRS jack) that holds. After some minutes of playing, notes could hang or drop out. The input now reads its buffer by content and not by the hardware's byte count, finds the start of a message again after a lost byte, releases the notes of a lost message and ignores aftertouch and pitch bend. A CC 7 / CC 11 value that repeats or jitters by one step (an expression pedal at rest) is no longer queued again, so the MIDI indicator no longer shows CC 11 all the time. The USB MIDI queue is 128 messages (it was 64).
  • Screen 4 (KNOB 1): test values. One row each: the load per stage, the sum of the wheels and the limiter's gain, the output peak and its limiter, MIDI and MIDI errors. The pedal screen keeps the load and the MIDI indicator.
  • Flash chip. The firmware runs on the newer FM-1 with the UC25HQ80 flash chip (accepted since 0.3); tested on both kinds.

Please note:

  • SAVE stores one global state, not one per preset.
  • Open: a line at 4190 Hz (the 12th harmonic of F4) that is louder on the Raspberry Pi; the Leslie at fast still has a little more noise than the Pi (partly the real Doppler); not explained yet.

Install: download b3organ-0.4.fwsc and use the FM-1 Firmware Hub, or see the README. 0.3 stays available under Releases as a fallback. Please report what sounds different from setBfree.

B3 ORGAN 0.3

Choose a tag to compare

@R-Jeb R-Jeb released this 11 Nov 10:50
5ce0fad

Three manuals, a new flash chip, finer reverb. What is new since 0.2:

Three manuals. Upper, lower and pedal, as in setBfree. Each has its own drawbars; the lower manual has its own vibrato on/off; the pedal has the 16' and 8' drawbars, no percussion and no vibrato. One scanner (vibrato / chorus) serves upper and lower, as in setBfree; the percussion and the pedal never go through it.
MIDI channels. Channel 1 plays the upper manual, 2 the lower one, 3 the pedal (USB and the TRS jack). The drawbar controllers 70 to 78 follow the channel (pedal: 70 = 16', 72 = 8').
Three screens (KNOB 1 switches): upper, lower, pedal. The manual of the screen shows its drawbars, the other two a line of digits. The chosen preset is on every screen. SELECT picks the drawbar, ALGORITHM sets it.
Screen 3 also shows the load of the audio block (µs, wheels sounding, peak) and a MIDI indicator: the channel and kind of the last message that came in (CH 2, ON, CC 64, PC 12) and a counter.
Keys: REC puts the FM-1's own keys on the upper, lower or pedal manual (shown as KEYS UPPER and so on on every screen). FX switches the vibrato of the screen's manual, LFO the Leslie, SEL the overdrive. EDIT and SAVE are left free.
Controls moved: the screen is on KNOB 1, KNOB 2 switches the vibrato / chorus V1, C1, V2, C2, V3, C3 (vibrato 1/2/3 and chorus 1/2/3), the overdrive amount (0 to 8) on KNOB 3, the reverb on KNOB 4, the overdrive on/off on SEL (it was EDIT).
Reverb in doubling steps on KNOB 4: 0, 1, 2, 4, 8, 16, 32, 64, 127 (fine at the bottom). CC 91 still sets any value.
New flash chip. Newer FM-1s carry a UC25HQ80 (JEDEC id 0xB36014) instead of the Puya P25Q80 (0x856014). The firmware and the update loader accept both now (as Dinghy 0.5): an older build saved to RAM only on the new chip, and its update loader did not know it. Tested on an FM-1 with the new chip: the firmware installs. Please say if your FM-1 has the new chip and it works.
Signal path changes that can be heard: the percussion is no longer modulated by the vibrato (it was in 0.2; setBfree keeps it dry), and the key compression counts the keys of all three manuals.
Measured, as in 0.2: with the same settings the overdrive behaves as in 0.2 (the level of every step against "overdrive off" within 0.3 dB); the Leslie (stop, slow, fast, ramps) agrees with a Raspberry Pi running setBfree in the modulation depth and the speeds.

Please note:

The saved settings have a new layout: the first start of 0.3 begins with the defaults (going back to 0.2 does the same).
A MIDI keyboard that sends CC 1, 64, 65 or 66 (modulation wheel, sustain, sostenuto) switches the Leslie, the overdrive or the percussion, as in setBfree. Screen 3 shows what arrives.
"Play in Browser" is still the upper manual only.
Open: a line at 4190 Hz (the 12th harmonic of F4) that is louder on the Raspberry Pi than here; not explained yet.
Install: download b3organ-0.3.fwsc and use the FM-1 Firmware Hub, or see the README. 0.2 stays available under Releases as a fallback. Please report what sounds different from setBfree.

B3 ORGAN 0.2

Choose a tag to compare

@R-Jeb R-Jeb released this 05 Nov 16:12
7014954

What is new since 0.1:

Overdrive is setBfree's preamp. The simple soft clip is replaced by setBfree's model (biased transfer curve between two bass filters, feedback, sag), in integers. The nine steps (KNOB 1, or CC 93) are setBfree's overdrive.character 0, 16 … 127. Measured against a Raspberry Pi: the level of every step against "overdrive off" agrees within 0.6 dB on a single note and 1.4 dB on a chord, including the dip at step 2 and the drop of step 0 below "off". The host tests check the model against setBfree's formulas (41 dB signal to error).
Battery indicator at the bottom right of the screen: four bars, red at the last bar, a bolt when a USB host has the FM-1.
Percussion click as setBfree's: the key attack comes out as a click in the percussion (6 dB before, 16 dB now against 15 dB on the Pi).
Lower load while many keys are held.
The firmware identifies as FM-1_953 for the FM-1 Firmware Hub.
Install: download b3organ-0.2.fwsc and use the FM-1 Firmware Hub, or see the README. Please report what sounds different from setBfree.

B3 ORGAN v0.1

Choose a tag to compare

@R-Jeb R-Jeb released this 05 Nov 07:35
b503e5f

A Hammond B3 tonewheel organ for the M-VAVE FM-1: 91 tonewheels, nine drawbars, key click and key compression, vibrato and chorus (V1 to C3), percussion (2nd or 3rd, slow or fast, soft or normal), overdrive, reverb, and a Leslie (stop, slow, fast) with horn and drum. All 110 setBfree programs and its default MIDI controllers (reverb on CC 91). Integer arithmetic only, one audio block of 256 samples at 44.1 kHz in 5.8 ms; with everything on, 10 keys, about 4 ms.

Everything is computed from setBfree’s own data and was compared with setBfree on a Raspberry Pi (48 kHz): chorus swing 14.8 cents as on the Pi, percussion level and decay within 0.4 dB and its key click within about 1 dB, reverb tails within 1 dB, the Leslie’s speeds and acceleration the same. What stays different: the stopped Leslie’s angle is random after each stop (as in setBfree), and the Pi has more above 2 kHz in a held note (its 12th harmonic is louder).

Install: download b3organ-0.1.fwsc and use the FM-1 Firmware Hub, or python3 tools/fm1_install.py b3organ-0.1.fwsc with the FM-1 connected by USB. Package identity FM-1_953. The official V15 and other firmware can be put back the usual way.

Based on setBfree (GPL), Felucca, SLOOP and Dinghy; see LICENSING.md. GPL-3.0.