v11.1.0

[dalathegreat]

What's Changed 📦

This release adds initial support for CCS charging. It also significantly improves connectivity, and Volkswagen MEB platform support with DTC reading.

Apart from all this, there are several other bugfixes and enhancements. Please check out the full list of changes below

Taking this release into use ⚙️

Important

In order to OTA update to this version, you already need to be on a v10 release!

Note that v10 was a major new release of the Battery-Emulator software. The first time when taking a version > v10.0.0 version into use, you are required to perform an initial one time USB setup via this webpage! This is because we changed the flash frequencies, partitioning layouts and other under the hood changes to ensure longterm system stability. After any v10 has been installed via USB, following 10.X.X releases can be updated over the air.

Quickstart video: https://youtu.be/sR3t7j0R9Z0

Batteries 🔋

• FEATURE: Add support for bidirectional charging via CCS by @M4GNV5 in Add support for bidirectional charging via CCS #2460
• MEB Battery: Add DTC reading via More Battery Info page by @malec1984 in MEB Battery: DTC report #2573
• MEB Battery: Read SoH from BMS by @malec1984 in MEB Battery: Read SoH from BMS #2614
• MEB Battery: Add sending of Klima_07 message to reduce number of DTCs by @dalathegreat in Volkswagen MEB: Add sending of Klima_07 message to reduce number of DTCs #2589
• Nissan Leaf: Improvement, balancing status now properly reported by @nagyrobi in Improvement: Nissan Leaf 🔋 balancing status #2588
• Pylon HV: Fix Pylon protocol compatibility with GCE and similar BMS by @BatteryPlug in Fix Pylon protocol compatibility with GCE and similar BMS #2622
• Tesla S/3/X/Y: 106s cell detect + Lower flash usage (Digital HVIL optimized) by @dalathegreat in Tesla S/3/X/Y: 106s cell detect + Lower flash usage (Digital HVIL optimized) #2578
• Flash optimization: Combine BYD/MEB DTC renderers together to save resources by @jonny5532 in Combine BYD/MEB DTC renderers together #2579

Connectivity 🛜

• Improvement: Wipe RF PHY calibration data on factory reset and network reset by @nagyrobi in Improvement: 🛜 Wipe RF PHY calibration data on factory reset and network reset #2598
• Improvement: Static IP single-field IP entry, add missing DNS server setting by @nagyrobi in Improvement: 🛜 Static IP single-field IP entry, add missing DNS server setting #2581
• Improvement: Cybersecurity, warn when AP starts with default password, log provisioning window expiry by @nagyrobi in Improvement: Warn when AP starts with default password, log provisioning window expiry #2593
• Bugfix: Disable WiFi driver persistence which may cause task stalls by @nagyrobi in Bugfix: 🐛 Disable WiFi driver persistence which may cause task stalls  #2591
• Bugfix: MQTT HA entity discovery issues and add third battery support for MQTT by @nagyrobi in Bugfix: 🐛 HA entity discovery issues and add third battery support #2577
• Bugfix: Remove double mDNS init 🐛 by @nagyrobi in Bugfix: remove double mDNS init 🐛 #2616
• Feature: Adds the "Battery charging! (Inverter limiting)" info via MQTT sensors by @StarkJohan in Adds the "Battery charging! (Inverter limiting)" info via MQTT sensors #2604

Inverters :zap

• Bugfix: 🐛 Apply inverter limits low pass filter to power limits by @nagyrobi in Bugfix: 🐛Apply inverter limits low pass filter to power limits #2621

Hardware 🤖

• Safety: ⚠️ Hold BMS_POWER pins active across reset/OTA reboot by @nagyrobi in Safety: ⚠️ hold BMS_POWER across reset/OTA reboot #2525

Housekeeping 🧹

• Improvement/Syslog 📜 pre-connectivity log backlog; task name as app name by @nagyrobi in Improvement/Syslog 📜 pre-connectivity log backlog; task name as app name #2585
• Improvement: Reduce header dependencies by moving #includes about, also save flash by @jonny5532 in Reduce header dependencies by moving #includes about #2609
• GitHub: Bump marocchino/sticky-pull-request-comment from 2 to 3 by @dependabot[bot] in Bump marocchino/sticky-pull-request-comment from 2 to 3 #2595
• GitHub: Bump actions/download-artifact from 4 to 8 by @dependabot[bot] in Bump actions/download-artifact from 4 to 8 #2596
• GitHub: Remove extraneous + signs from measure action by @jonny5532 in GitHub: Remove extraneous + signs from measure action #2610
• GitHub: Improve binary size tracking v3 by @ngehrsitz in Improve binary size tracking v3 #2594
• GitHub: Make firmware size report clearer, add links by @jonny5532 in Make firmware size report clearer, add links #2606

New Contributors

• @ngehrsitz made their first contribution in Improve binary size tracking #2561
• @BatteryPlug made their first contribution in Fix Pylon protocol compatibility with GCE and similar BMS #2622

Full Changelog: v11.0.0...v11.1.0

---

This discussion was created from the release v11.1.0.

[Robertino68]

Ottimo, con questo aggiornamento sono riuscito a passare dalla versione 10.13.0 che mi dava problemi alla 11.1.0 senza resettare la scheda.
Grazie