Skip to content

Releases: fivefold3/openwrt-gl-be3600

Release list

v1.0: stock OpenWrt for the GL.iNet Slate 7 (GL-BE3600)

v1.0: stock OpenWrt for the GL.iNet Slate 7 (GL-BE3600) Latest
Latest

Choose a tag to compare

View all tags
@fivefold3 fivefold3 released this 25 Sep 10:54
v1.0
5159929

OpenWrt for the GL.iNet Slate 7 (GL-BE3600): the stock image.

OpenWrt's default packages for the target, the router's hardware support
(both Wi-Fi radios with their firmware and board data, both 2.5 GbE ports,
USB 3.0 host, fan, side screen and touch drivers) and the LuCI web interface.
Nothing else. For USB modems, tethering, USB storage, file sharing and VPNs,
use the extended release.

Built from commit 5159929 on branch gl-be3600 (OpenWrt SNAPSHOT
r0-5159929, Linux 6.18.39) with configs/be3600.config.

Installing

File Use
…-squashfs-factory.bin First install: from the stock GL.iNet firmware's local-upgrade page ("keep settings" off), or from U-Boot web recovery
…-squashfs-sysupgrade.bin From OpenWrt already on the router: sysupgrade keeps settings, sysupgrade -n wipes them

U-Boot web recovery (also the way back to stock): power off, hold reset,
apply power and keep holding until recovery starts; set the PC to
192.168.1.2/24, open http://192.168.1.1, upload the file, wait about three
minutes.

First boot: plug your computer into the LAN jack; it gets an address
from the router at 192.168.1.1. The WAN jack is the uplink and takes its
own address by DHCP from your modem or upstream network. LuCI is at
http://192.168.1.1 and SSH is root@192.168.1.1, both with no password until
you set one. Both Wi-Fi radios are present but disabled, as OpenWrt does by
default: enable them under Network → Wireless.

Regulatory country: both radios take the country code stored in the
router's calibration partition. If you use it elsewhere, set both radios
to the country of use (Network → Wireless → radio → Advanced).

Packages: there is no online package repository for this build. Kernel
modules only load on the kernel they were built with, so add packages by
building them from the source; see "Adding packages" in the README.

Warning

Unofficial community port, not affiliated with GL.iNet or the OpenWrt
project, provided as-is with no warranty. Back up the NAND before the first
install (scripts/gl-be3600/backup-mtd.sh): the 0:ART partition holds
the router's radio calibration and MAC addresses and exists nowhere else.
Tested on one GL-BE3600.

Known limitations

  • RTL8811AU (11ac) USB Wi-Fi clients cannot associate on 5 GHz.
  • Board data covers GL's plain hardware variants; the suffixed variants
    (KCT, 33V, HP, LP) are untested.
  • No cross-band MLO: the two radios are separate, as usual on OpenWrt.

SHA-256

fba40ed37b88c59675986d8e7fd95c7d1bc82a511b0219386cd14b99d1668c06  openwrt-qualcommbe-ipq53xx-glinet_gl-be3600-squashfs-factory.bin
ca26e9124b53b6374ad00e83696c8cd9c1d60f483ea6d8a7568ce95e073d7509  openwrt-qualcommbe-ipq53xx-glinet_gl-be3600-squashfs-sysupgrade.bin
e32b132776ceb8eff6071c90e1e8ce1f78f34e2ea9515c0b26dfc3c3c6a4b39b  openwrt-qualcommbe-ipq53xx-glinet_gl-be3600.manifest
Assets 6
Loading

v1.0 extended: OpenWrt for the GL.iNet Slate 7 (GL-BE3600) with modem, storage and VPN support

v1.0 extended: OpenWrt for the GL.iNet Slate 7 (GL-BE3600) with modem, storage and VPN support

Choose a tag to compare

View all tags
@fivefold3 fivefold3 released this 25 Sep 10:54
v1.0-extra
5159929

OpenWrt for the GL.iNet Slate 7 (GL-BE3600): the extended image.

Everything in the stock image, plus:

  • USB modems: QMI, MBIM, NCM, PPP dial-up, ECM and RNDIS modems with
    their LuCI protocols, the serial AT ports of Option, Quectel, Sierra and
    Qualcomm modems, mode switching (usb-modeswitch) and picocom.
  • Tethering and USB Ethernet: iPhone and Android tethering, Realtek
    RTL8152/RTL8153 and ASIX AX88179 adapters.
  • USB storage and file sharing: UAS, vfat, exfat, ntfs3, ext4 and f2fs,
    automatic mounting (block-mount), and Samba with its LuCI page.
  • VPN: WireGuard and OpenVPN, both configured under Network → Interfaces.
  • Tools: tcpdump, nano, openssl-util, ethtool, LuCI over HTTPS.
  • Side-screen spinner: an animation on the side screen with a touch trail,
    started at boot. Turn it off with
    uci set slate-spinner.main.enabled=0 && uci commit slate-spinner && /etc/init.d/slate-spinner stop.

The full package list is in the .manifest file below.

Built from commit 5159929 on branch gl-be3600 (OpenWrt SNAPSHOT
r0-5159929, Linux 6.18.39) with configs/be3600-extra.config.

Installing

File Use
…-squashfs-factory.bin First install: from the stock GL.iNet firmware's local-upgrade page ("keep settings" off), or from U-Boot web recovery
…-squashfs-sysupgrade.bin From OpenWrt already on the router: sysupgrade keeps settings, sysupgrade -n wipes them

U-Boot web recovery (also the way back to stock): power off, hold reset,
apply power and keep holding until recovery starts; set the PC to
192.168.1.2/24, open http://192.168.1.1, upload the file, wait about three
minutes.

First boot: plug your computer into the LAN jack; it gets an address
from the router at 192.168.1.1. The WAN jack is the uplink and takes its
own address by DHCP from your modem or upstream network. LuCI is at
http://192.168.1.1 and SSH is root@192.168.1.1, both with no password until
you set one. Both Wi-Fi radios are present but disabled, as OpenWrt does by
default: enable them under Network → Wireless.

Regulatory country: both radios take the country code stored in the
router's calibration partition. If you use it elsewhere, set both radios
to the country of use (Network → Wireless → radio → Advanced).

Packages: there is no online package repository for this build. Kernel
modules only load on the kernel they were built with, so add packages by
building them from the source; see "Adding packages" in the README.

Warning

Unofficial community port, not affiliated with GL.iNet or the OpenWrt
project, provided as-is with no warranty. Back up the NAND before the first
install (scripts/gl-be3600/backup-mtd.sh): the 0:ART partition holds
the router's radio calibration and MAC addresses and exists nowhere else.
Tested on one GL-BE3600.

Known limitations

  • RTL8811AU (11ac) USB Wi-Fi clients cannot associate on 5 GHz.
  • Board data covers GL's plain hardware variants; the suffixed variants
    (KCT, 33V, HP, LP) are untested.
  • No cross-band MLO: the two radios are separate, as usual on OpenWrt.

SHA-256

f1fbe7129088ed3d209c62f9348416efa8c9a30e969d4701af4265f1aa2d5aed  openwrt-extra-qualcommbe-ipq53xx-glinet_gl-be3600-squashfs-factory.bin
698da93d7699f6220cbc8f2b976c6bd3d268172e9982e64d4a85d8163919d7a2  openwrt-extra-qualcommbe-ipq53xx-glinet_gl-be3600-squashfs-sysupgrade.bin
90dcc78a72d48feb97cb33e48c7d9e5043eabdf30695af9b8866b1fadea5098c  openwrt-extra-qualcommbe-ipq53xx-glinet_gl-be3600.manifest
Loading