HydraFW 1 wire guide

Benjamin Vernoux edited this page Oct 1, 2018 · 5 revisions

HydraFW Bus 1-wire

Bus: 1-wire
Connections: One pin and ground
Output types: open drain/open collector
Pull-up resistors: required for open drain output mode (2K – 10K).
Pull-up/down resistors Integrated in MCU: Between 30 to 50K (Typical 40K).
Maximum voltage: 5.5volts (5volt safe)

This guide is updated towards firmware release HydraFW v0.9 Beta

Protocol configuration syntax description:

  • show Show 1-wire parameters or show pins Show pins used in this mode

  • pull with parameter up or down or floating to choose internal MCU pull up/down or no pull/external

  • msb-first or lsb-first to send/receive respectively MSB first or LSB first.

  • scan Discovers device on the 1-wire bus and displays their addresses.

  • exit to exit 1-wire mode

Note default value: 
    > 1-wire 
    Device: onewire1
    GPIO resistor: floating
    Bit order: LSB first

Configuration options:

Hardware Informations:

onewire1> show pins 
PIN: PB11

Protocol configuration example:

Configuration of onewire1 wit internal pullup :

> 1-wire 
Device: onewire1
GPIO resistor: floating
Bit order: LSB first
onewire1> pull up
onewire1> show 
Device: onewire1
GPIO resistor: pull-up
Bit order: LSB first
onewire1> 

Protocol interaction syntax description:

trigger configures the trigger mode

r or read Read one byte. (r:1…255 for bulk reads)

hd Read one byte. (hd:1…4294967295 for bulk reads). Displays a hexdump of the result (See Hexdump guide)

w or write Followed by values to write byte(s). (w:1…255 for bulk writes)

0 Write this Octal value. Format is prefixed by a 0 (values from 000 to 077)

0b Write this binary value. Format is 0b00000000 for a byte, but partial bytes are also fine: 0b1001.

0x Write this HEX value. Format is 0x01. Partial bytes are fine: 0xA. A-F can be lower-case or capital letters.

0-255 Write this decimal value. Any number not preceded by 0x or 0b is interpreted as a decimal value.

" Write an ASCII-encoded string

Write support optional repeat : (eg.: 10:1…255 for repeated write of same value 10 in this example)

space Value delimiter. Use a space to separate numbers/commands. Any combination is fine, delimiter is required between each number/command, example: [ 0x1 0xff 0 10 0b11 077 ]

& Delay 1uS. (&:1…1000000 for multiple delays)

% Delay 1mS. (%:1…1000000 for multiple delays)

~ Write a random byte. (~:10 repeats the same random byte 10 times)

Protocol interaction example usage onewire1 write/read:

onewire1> scan 
Discovered devices : 28 FF 10 2E A6 15 01 3B 
onewire1> [ 0x33 hd:8
WRITE: 0x33
28 FF 10 2E A6 15 01 3B                           |  (......; 

Additional informations about 1-wire

For more information about the 1-wire protocol, see : https://www.maximintegrated.com/en/app-notes/index.mvp/id/1796

Clone this wiki locally
You can’t perform that action at this time.
You signed in with another tab or window. Reload to refresh your session. You signed out in another tab or window. Reload to refresh your session.
Press h to open a hovercard with more details.