EL-A3 Robotic Arm

7-DOF 桌面机械臂项目，包含纯 Python SDK 和 ROS2 控制系统两个独立子项目。

---

子项目

项目	路径	说明
Python SDK	el_a3_sdk/	纯 Python SDK，Direct CAN 通信，多臂管理，Pinocchio 动力学
ROS2 控制系统	el_a3_ros/	ros2_control 硬件接口，MoveIt2 运动规划，URDF 描述
硬件制造资料	hardware/	STEP 模型、3MF 打印文件、线束图纸、PCB 资料、组装 SOP

各子项目的详细文档请参阅对应目录下的 README.md。

注意： hardware/ 目录中的大文件通过 Git LFS 管理，首次克隆后请执行 git lfs pull。

---

硬件要求

项目	规格
机械臂	EL-A3 7-DOF（6 臂关节 + L7 夹爪）
电机	Robstride RS00 ×3（L1-L3）+ EL05/RS05 ×4（L4-L7）
CAN 适配器	CANdle / gs_usb 兼容设备
电源	24V / 48V 直流电源
PC	Ubuntu 22.04+ x86_64

电机配置

关节	电机ID	型号	力矩限制	速度限制	位置限制	方向
L1	1	RS00	±14 Nm	±33 rad/s	±2.79 rad (±160°)	-1
L2	2	RS00	±14 Nm	±33 rad/s	03.67 rad (0°210°)	+1
L3	3	RS00	±14 Nm	±33 rad/s	-4.010 rad (-230°0°)	-1
L4	4	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	+1
L5	5	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	-1
L6	6	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	+1
L7（夹爪）	7	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	+1

软件环境

依赖	版本 / 说明
操作系统	Ubuntu 22.04+ (x86_64)
Python	3.10+
ROS2	Humble Hawksbill（仅 ROS2 子项目需要）
CAN 总线	SocketCAN · CAN 2.0 扩展帧 · 1 Mbps
核心 Python 依赖	numpy、pyyaml
可选 Python 依赖	pinocchio（pip install pin）— FK/IK/重力补偿
ROS2 依赖	ros2_control、MoveIt2、pick_ik、joy 等（通过 scripts/install_deps.sh 安装）

CAN 接口配置

# 使用脚本（推荐）
sudo bash scripts/setup_can.sh can0 1000000

# 或手动配置
sudo modprobe gs_usb
sudo ip link set can0 type can bitrate 1000000
sudo ip link set can0 txqueuelen 1000
sudo ip link set can0 up

# 验证
ip link show can0

---

English

A 7-DOF desktop robotic arm project comprising two independent sub-projects: a pure Python SDK and a ROS2 control system.

Sub-projects

Project	Path	Description
Python SDK	el_a3_sdk/	Pure Python SDK with direct CAN communication, multi-arm management, and Pinocchio dynamics
ROS2 Control System	el_a3_ros/	ros2_control hardware interface, MoveIt2 motion planning, URDF description
Hardware Manufacturing	hardware/	STEP models, 3MF print files, wiring harness drawings, PCB files, assembly SOP

For detailed documentation, refer to the README.md in each sub-project directory.

Note: Large files in the hardware/ directory are managed via Git LFS. Run git lfs pull after initial clone.

Hardware Requirements

Item	Specification
Robotic Arm	EL-A3 7-DOF (6 arm joints + L7 gripper)
Motors	Robstride RS00 ×3 (L1-L3) + EL05/RS05 ×4 (L4-L7)
CAN Adapter	CANdle / gs_usb compatible device
Power Supply	24V / 48V DC
PC	Ubuntu 22.04+ x86_64

Motor Configuration

Joint	Motor ID	Model	Torque Limit	Velocity Limit	Position Limit	Direction
L1	1	RS00	±14 Nm	±33 rad/s	±2.79 rad (±160°)	-1
L2	2	RS00	±14 Nm	±33 rad/s	03.67 rad (0°210°)	+1
L3	3	RS00	±14 Nm	±33 rad/s	-4.010 rad (-230°0°)	-1
L4	4	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	+1
L5	5	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	-1
L6	6	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	+1
L7 (Gripper)	7	EL05/RS05	±6/±5.5 Nm	±50 rad/s	±1.57 rad (±90°)	+1

Software Environment

Dependency	Version / Notes
OS	Ubuntu 22.04+ (x86_64)
Python	3.10+
ROS2	Humble Hawksbill (required only for the ROS2 sub-project)
CAN Bus	SocketCAN · CAN 2.0 Extended Frame · 1 Mbps
Core Python Dependencies	numpy, pyyaml
Optional Python Dependencies	pinocchio (pip install pin) — FK/IK/Gravity compensation
ROS2 Dependencies	ros2_control, MoveIt2, pick_ik, joy, etc. (install via scripts/install_deps.sh)

CAN Interface Setup

# Using the provided script (recommended)
sudo bash scripts/setup_can.sh can0 1000000

# Or configure manually
sudo modprobe gs_usb
sudo ip link set can0 type can bitrate 1000000
sudo ip link set can0 txqueuelen 1000
sudo ip link set can0 up

# Verify
ip link show can0