Skip to content

Material preparation

LatroX-dev edited this page Nov 21, 2026 · 1 revision

Five fractions, three preparation stages

The Hand Preparator starts the matrix chain. Powered machines take over repeated work and supply the additional fractions for larger Cells.

Extract one material at a time

Leave the middle and right inputs empty for extraction. Each batch uses one input and produces one fraction.

Primary input Output First available machine
Sand Silith Hand Preparator
Clay Ball Argil Hand Preparator
Redstone Dust Rhedon Material Preparator
Nether Quartz Virel Material Preparator
Glowstone Dust Lumin Material Preparator

To make four Matrix Blend, put one Silith in the primary input and one Argil in the second input. A raw sand/clay pair is not the mixing recipe.

These are named fractions for the matrix technology, not purified elements. No added water or fluid connection is needed.

Let FE do the work

Craft a Material Preparator with two Amber Matrix Crystals, Structural Bars, Machine Frames and Control Circuits. Connect an enabled side or rear port to your Crystal Generator or another FE supply. The Preparator starts when the input, power and output space are ready. Press Start to resume it if paused.

At base speed, an extraction takes 2,000 FE and 18 seconds. Mixing takes 4,000 FE and 24 seconds. Grinding, sieving and mixing are stages of one batch. They are not separate machines.

The three ingredient slots are arranged left → middle → right. Matrix Blend uses Silith on the left and Argil in the middle. The right slot stays empty. Alloy and ceramic powders use all three slots and have their own costs and durations.

Recipe for Material Preparator.

Larger matrix assemblies

A Matrix Cluster combines four Matrix Crystals with Rhedon, Virel, Structural Bars and Matrix Blend. An Optical Circuit combines Lumivex Ingots, glass, Diamond Lattices and a Control Circuit. Make Lumivex through the powder and sintering chain. The larger Cell recipes show where both assemblies are used.

Recipes for Matrix Cluster, Optical Circuit.

The fractions remain physical ingredients in these assemblies. Learning the recipes does not provide them or fill a new Cell.

Mount the working parts

Fit at least one Resonance Cutter, Phase Filter and Confluence Basin. Every type can mount on either the inside floor or the underside of the roof. The field carries material between parts. Their function does not depend on gravity.

Click a supporting block's top face for a floor fitting or underside for a ceiling fitting. The socket turns automatically so the crystal points into the chamber. Sideways and unsupported placement are rejected. Keep the middle of the chamber empty.

Each type has a different crystal core and a small symbol. Its item and mounted appearance identify the same part. Ceiling fittings are mirrored floor fittings.

Recipes for Preparation Reactor Controller, Resonance Cutter, Phase Filter, Confluence Basin.

Close the shell

Outer width and depth can each be 3–9 blocks. Use a footprint of at least 3×4 or 4×3 so the floor and ceiling have room for all three fittings. Build 5–9 blocks high, including floor and roof. Use Reactor Casings on every edge and corner, Glass or Casing panels elsewhere and at least two Ports away from edges. Put the controller in the front wall, one block above the base.

This 5 wide × 3 deep × 6 high example uses 40 Casings, 35 Glass, 2 Ports, 1 controller and one of each preparation module. The Basin and Filter are on the floor. The Cutter is on the ceiling. Their positions on the two mounting planes are your choice.

View the example one layer at a time

Read from the floor up. The first row of each layer is the front wall. Dots mark empty spaces.

@ Preparation Reactor Controller · B Confluence Basin · C Reactor Casing · G Reactor Glass · P Machine Port · R Resonance Cutter · T Phase Filter

Layer 1 (floor)
C C C C C
C G G G C
C C C C C

Layer 2
C G @ G C
P B . T G
C G G G C

Layer 3
C G P G C
G . . . G
C G G G C

Layer 4
C G G G C
G . . . G
C G G G C

Layer 5
C G G G C
G . R . G
C G G G C

Layer 6 (roof)
C C C C C
C G G G C
C C C C C

Ports work only after the complete chamber forms. Connect external FE to an outward Port face. Enable Automation for item transport. Casing, Glass, internal modules and the controller are not external transfer connections. You can also configure the chamber blueprint or press Auto-Build in Settings → Structure (or right-click the unformed controller with a Matter Wrench in Ports mode). If any foreign block obstructs full construction, Auto-Build places nothing, warns you and enables the world preview.

Add more working parts

Cutters provide grinding capacity, Basins provide mixing capacity, and Filters add Precision. More modules allow more capable or simultaneous work. They do not add a second global speed multiplier. The industrial tier has a fixed base work rate before upgrades. Height, Parallel Upgrades and enough capacity for every recipe step are all required for extra lanes.

Industrial preparation starts at twice a recipe's declared FE. Phase Filters do not discount it. Speed and Efficiency use separate upgrade slots. Parallel has its own slot. Inspect actual FE, Precision, step capacity and active jobs in the controller. All jobs share the same matter-transfer budget.

A larger empty shell adds no throughput. Pause before moving modules.

Clone this wiki locally