v1.92.2

What's new in 1.92.2

• An OBJ from Tinkercad comes in the right way up
  Tinkercad writes its OBJ files with Z up. layerling used to read them with Y up, so a part stood on its edge. layerling now recognises a Tinkercad file and sets it down the right way: a flat part lies flat.
• A .lyl file opens with a double click
  When layerling is installed as an app (Chrome or Edge), it registers itself with the system as a program for .lyl files. A double click on a design in the file manager opens it in layerling right away, and Ctrl+S saves back into that file. The system asks once which program to use.
• Docker: the preview pictures appear
  In the ready-made Docker image the cards on the start page stayed on "No preview yet", because the server was not allowed to create a folder for the pictures. The folder now belongs to the server's user, so the pictures are saved again. For an existing container, pull the image again; the pictures appear the next time a design is opened.
• Docker behind a proxy: saving to the server works
  If you run layerling behind a reverse proxy with a domain and HTTPS, saving to the server failed with "Shared projects only accept requests from this site". layerling now copes with a proxy that ends HTTPS without passing that on. If the proxy changes the host, list the domain in LAYERLING_ALLOWED_ORIGINS.
• Delete all reference points in the menu of an empty spot too
  If you had set a reference point with the tape measure and right-clicked next to it, you found only Paste, Select all and Select multiple. "Delete all reference points" is now in the menu of an empty spot of the 3D view too, whenever the design holds a reference point.
• The number field of the corner ruler closes on deselect
  A click on a green number of the corner ruler opens a field to type into. It stayed in the view even when the body was no longer selected. It now closes (without applying) as soon as the bodies it was opened for are no longer all selected.

---

Kaj je novega v 1.92.2

• OBJ iz Tinkercada pride pravilno obrnjen
  Tinkercad zapiše datoteke OBJ z osjo Z navzgor. Layerling jih je prej bral z osjo Y navzgor, zato je del stal na robu. Layerling zdaj prepozna datoteko iz Tinkercada in jo postavi pravilno: ploščat del leži ploščato.
• Datoteka .lyl se odpre z dvojnim klikom
  Ko je Layerling nameščen kot aplikacija (Chrome ali Edge), se pri sistemu prijavi kot program za datoteke .lyl. Dvojni klik na osnutek v upravitelju datotek ga takoj odpre v Layerlingu, Ctrl+S pa shrani nazaj v to datoteko. Sistem enkrat vpraša, kateri program uporabiti.
• Docker: predogledne slike se pojavijo
  V že pripravljeni sliki Docker so kartice na začetni strani ostale pri »Še ni predogleda«, ker strežnik ni smel ustvariti mape za slike. Mapa zdaj pripada uporabniku strežnika, zato se slike spet shranjujejo. Pri obstoječem vsebniku sliko znova povleci; slike se pojavijo, ko osnutek naslednjič odpreš.
• Docker za posredniškim strežnikom: shranjevanje na strežnik deluje
  Če poganjaš Layerling za obratnim posredniškim strežnikom z domeno in HTTPS, shranjevanje na strežnik ni uspelo z »Skupni projekti sprejemajo zahteve samo s tega mesta«. Layerling se zdaj spopade s posrednikom, ki konča HTTPS, a tega ne posreduje naprej. Če posrednik spremeni gostitelja, domeno navedi v LAYERLING_ALLOWED_ORIGINS.
• Izbriši vse referenčne točke tudi v meniju praznega mesta
  Če si z merilnim trakom nastavil referenčno točko in desno kliknil ob njej, si našel samo Prilepi, Izberi vse in Izberi več. »Izbriši vse referenčne točke« je zdaj tudi v meniju praznega mesta 3D pogleda, kadar osnutek vsebuje referenčno točko.
• Številčno polje kotnega ravnila se ob odznačitvi zapre
  Klik na zeleno številko kotnega ravnila odpre polje za vnos. Ostalo je v pogledu, tudi ko telo ni bilo več izbrano. Zdaj se zapre (brez uveljavitve), čim telesa, za katera je bilo odprto, niso več vsa izbrana.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.92.2) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.92.2) s slovenskim vmesnikom.

v1.92.1

What's new in 1.92.1

• Narrower: move a sketch outline inwards
  Next to "Wider", the fill of a sketch body now has "Narrower": the area stays filled and its edge moves in by the line width all round, holes grow. One sketch gives the fit hole and the part that passes through it 0.5 mm smaller, or an inner wall.
• Set the space between the letters
  Texts now have a letter spacing in per cent of the letter size, also negative and on curved text. That helps most with fonts of your own that stand too tight or too wide. The letters keep their size and the box follows the line.
• Bodies under a sketch show their real outline
  In sketch mode the bodies on the workplane now show in the background with their real outline: a polygon, a star, a heart, a wedge and the other shapes were all drawn as a square there. The sketch's snap points follow that outline as well.
• The shortcuts print on one sheet
  The printer button in the shortcuts window now puts the whole list, in the editor and in sketch mode, on one sheet (A4 or Letter): black on white, in three columns, as a quick reference to keep at hand.
• Right-angle snapping and quick delete in the tape measure
  When placing the second point of a measurement, the tape measure now snaps at a right angle to an opposing edge or face - or anywhere on it while you hold Shift, which makes measuring the clear width of a hole or the gap between two parts exact. And while adding measurements, a click with Shift or Ctrl (Cmd on a Mac) deletes a point or a line right away without switching modes.
• Corner ruler: X and Y are the right way round
  On the corner ruler the green numbers had the tooltips "X position" and "Y position to ruler" the wrong way round: when a body moved to the back, the number with the X tooltip changed. Now each number is named by the direction of its arm: X to the right, Y to the back, Z up, also after the ruler is turned by a quarter.
• Snap grid reachable with several parts selected
  With several parts selected, the panel on the right reached down to the bottom and covered the snap grid choice in the corner. The snap grid, with the switch for snapping to shapes, now sits at the foot of that panel, as it does for a single part. Move the panel away and it is back in the corner.
• Selection frame: green for "touching"
  Drag the frame from right to left (or the other way round with Alt) and it takes everything it touches. It is now green and dashed then, so you see at once how it selects. The frame that must enclose parts completely stays orange.

---

Kaj je novega v 1.92.1

• Ožje: obris skice premakni navznoter
  Ob »Širše« ima zapolnitev telesa skice zdaj tudi »Ožje«: ploskev ostane zapolnjena, njen rob se premakne navznoter za širino črte, luknje pa se povečajo. Ena skica da luknjo za prileganje in del, ki gre skozi njo, 0,5 mm manjši, ali notranjo steno.
• Nastavi razmik med črkami
  Besedila imajo zdaj razmik med črkami v odstotkih velikosti črke, tudi negativen in na ukrivljenem besedilu. To najbolj pomaga pri lastnih pisavah, ki stojijo pretesno ali preširoko. Črke obdržijo velikost, okvir pa sledi vrstici.
• Telesa pod skico kažejo svoj pravi obris
  V načinu skice se telesa na delovni ravnini v ozadju zdaj kažejo s pravim obrisom: mnogokotnik, zvezda, srce, klin in druge oblike so bile tam vse narisane kot kvadrat. Tudi pritrdilne točke skice sledijo temu obrisu.
• Bližnjice se natisnejo na en list
  Gumb tiskalnika v oknu bližnjic zdaj celoten seznam, v urejevalniku in v načinu skice, natisne na en list (A4 ali Letter): črno na belem, v treh stolpcih, kot hitra referenca pri roki.
• Pravokotno pritrjevanje in hitro brisanje pri merilnem traku
  Pri postavljanju druge točke meritve se merilni trak zdaj pritrdi pravokotno na nasprotni rob ali ploskev, ali kjer koli na njej, ko držiš Shift, zaradi česar je merjenje čiste širine luknje ali reže med dvema delovoma natančno. Med dodajanjem meritev klik s Shiftom ali Ctrl (Cmd na Macu) takoj izbriše točko ali črto, ne da bi menjal način.
• Kotno ravnilo: X in Y sta spet prav obrnjena
  Na kotnem ravnilu sta imeli zeleni števili namige »Položaj X« in »Položaj Y do ravnila« napačno obrnjena: ko se je telo premaknilo nazaj, se je spremenila številka z namigom X. Zdaj je vsaka številka poimenovana po smeri svojega kraka: X v desno, Y nazaj, Z navzgor, tudi ko ravnilo zavrtiš za četrtino.
• Pritrdilna mreža dosegljiva ob izbranih več delih
  Ob izbranih več delih je plošča na desni segala do dna in prekrila izbiro pritrdilne mreže v kotu. Pritrdilna mreža s stikalom za pritrjevanje na oblike zdaj stoji na dnu te plošče, kot pri enem delu. Ploščo odmakni in vrne se v kot.
• Okvir izbire: zelen za »dotikanje«
  Povleci okvir z desne na levo (ali obratno z Alt) in vzame vse, česar se dotakne. Takrat je zdaj zelen in črtkan, da takoj vidiš, kako izbira. Okvir, ki mora dele povsem zajeti, ostane oranžen.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.92.1) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.92.1) s slovenskim vmesnikom.

v1.92.0

What's new in 1.92.0

• A revolve can wind up as one continuous strand
  A revolved body now has a Pitch in the Properties panel. Above 0 the outline winds up as a helix instead of rings, like filament on a spool, and you set the number of turns.
• Alt turns the selection frame around
  Hold Alt while you drag a selection frame: it works the other way round for that one drag. With the setting "The direction of the frame decides" on, a frame dragged to the right then takes everything it touches and one dragged to the left only what lies completely inside. With the setting off, Alt takes only what lies completely inside.
• An engraving around a cylinder cuts all the way through
  A logo wrapped inward and cut out of a cylinder as a hole left a hair-thin skin standing in places. The wrapped body now reaches 0.05 mm beyond the wall, so the hole cuts all the way through.
• The wheel in a size field stops at the lower limit
  The mouse wheel in a size field of the properties no longer runs below the smallest value (0.01 mm) into negative numbers: the field stops at the limit.
• Tiny bodies can be moved on a tablet again
  When a selected body is very small on the screen, a finger no longer grabs a handle instead of the body: the handles' wide catch zones are dropped then, and the middle stays free for dragging.
• A see-through body has a see-through cut face
  When you cut a see-through body in the section view, the filled cut face is now as see-through as the body, no longer solid.
• The sketch's shape panel: its own place and size
  The sketch's shape panel now remembers its place, its pin and its size on its own and no longer shares them with the 3D editor. Its edges and corners can be pulled to the size you want, like the 3D editor's panel.
• No offline promise where it cannot work
  The card "Install layerling as an app" and the "Works offline" tile on the start page now appear only where layerling can really keep itself for offline use. In the Docker image, which runs as a Node server, and at a plain-http address they are gone.
• The view cube can sit in any corner
  Settings > Appearance > View cube position puts the view cube in the top left, top right, bottom left or bottom right of the workplane. In any corner but the top left, the camera controls move up into its place.
• Traced SVGs stay small enough to join
  An imported SVG with very many curves, such as a traced drawing, was cut into over 350,000 triangles, so several copies could no longer be joined. It is now about ten times fewer, and the drawing looks the same at that size. Sketches drawn by hand stay as fine as before.
• Thin, small letters are no longer lost in the export
  A small, flat text lost single letters in the export as STL, 3MF or OBJ, with a thin text most of them: the dot of the i, the apostrophe, small letters. The export took them for splinters that a cut had left behind. That now applies only to bodies that a cut, a merge of several bodies or the colour separation has changed.
• An SVG with touching shapes comes in whole
  In a drawn or traced picture two shapes often meet in just one point. The import then left some shapes out, and the picture came in smaller and with gaps. Such shapes are now built together, and the picture stays whole.
• The chamfillet on a cylinder sits at the foot again
  A chamfillet on the bottom edge of a cylinder came out the wrong way round: the fillet at the foot, the chamfer above it, and the top rim rounded as well. Now the chamfer sits on the plate and blends into the wall, and the top rim stays untouched.
• Typing Japanese and Chinese into the Text field
  With an input method (IME) nothing sensible could be typed into the Text field of a text or a name tag: "ishi" came out as "いｓｈい" and could not be converted to kanji. The field now keeps what is typed and takes a word over once it is done. This holds for Japanese, Chinese and Korean.
• Interactive Help explains each setting on its own
  In the Workspace settings, a click with Interactive Help on often led only to a long section, or to nothing. Now the guide has a section of its own for each group of settings (English and German), plus "Choosing colours" for the colour card, and the fields, sliders, colour buttons and lists find their section, the Fast mode switch too.
• The History view says what the arrows undo and redo
  Under the slider of the History view, a row now names the step the left arrow would undo ("Last step: Moved Box") and the one the right arrow would redo ("Next step: Grouped 2 objects into Group"), with "none" at the oldest and the newest state. It also works for designs saved before.

---

Kaj je novega v 1.92.0

• Vrtenje se lahko navije v eno neprekinjeno nit
  Zavrteno telo ima zdaj v oknu lastnosti polje Korak. Nad 0 se obris ne navije v kolobarje, temveč v vijačnico, kot nit na kolutu, število ovojev pa nastaviš sam.
• Alt obrne okvir izbire
  Drži Alt med vlečenjem okvira izbire: za tisto vleko deluje obratno. Če je vklopljena nastavitev »Smer okvira odloča«, okvir, povlečen v desno, vzame vse, česar se dotakne, okvir, povlečen v levo, pa le tisto, kar leži povsem znotraj. Če je nastavitev izklopljena, Alt vzame samo tisto, kar leži povsem znotraj.
• Gravura okoli valja prereže skozi in skozi
  Logotip, ovit navznoter in izrezan iz valja kot luknja, je na mestih pustil lasasto tanko kožico. Ovito telo zdaj sega 0,05 mm čez steno, zato luknja prereže vse do konca.
• Kolesce v polju velikosti se ustavi pri spodnji meji
  Kolesce miške v polju velikosti v lastnostih ne zdrsne več pod najmanjšo vrednost (0,01 mm) v negativna števila: polje se ustavi pri meji.
• Drobna telesa je na tablici spet mogoče premikati
  Kadar je izbrano telo na zaslonu zelo majhno, prst ne zagrabi več ročice namesto telesa: široka področja ročic se takrat opustijo, sredina pa ostane prosta za vlečenje.
• Prosojno telo ima prosojno prerezano ploskev
  Ko v pogledu prereza prerežeš prosojno telo, je zapolnjena prerezana ploskev zdaj enako prosojna kot telo in ni več polna.
• Okno oblik v skici: svoje mesto in velikost
  Okno oblik v skici si zdaj samo zapomni svoje mesto, pripetost in velikost in jih ne deli več s 3D urejevalnikom. Robove in vogale lahko povlečeš na želeno velikost, kot pri oknu 3D urejevalnika.
• Brez obljube delovanja brez povezave, kjer ne more delovati
  Kartica »Namesti Layerling kot aplikacijo« in ploščica »Deluje brez povezave« na začetni strani se zdaj pokažeta samo tam, kjer se Layerling res lahko shrani za uporabo brez povezave. V sliki Docker, ki teče kot strežnik Node, in na navadnem naslovu http ju ni.
• Kocka pogleda je lahko v katerem koli kotu
  Nastavitve > Videz > Položaj kocke pogleda postavi kocko pogleda zgoraj levo, zgoraj desno, spodaj levo ali spodaj desno na delovni ravnini. V vseh kotih razen zgoraj levo se upravljanje kamere premakne navzgor na njeno mesto.
• Posnete datoteke SVG ostanejo dovolj majhne za združevanje
  Uvožen SVG z zelo veliko krivuljami, na primer posneta risba, je bil razrezan na več kot 350.000 trikotnikov, zato več kopij ni bilo mogoče več združiti. Zdaj jih je približno desetkrat manj, risba pa je v tej velikosti videti enako. Ročno narisane skice ostanejo enako fine kot prej.
• Tanke, majhne črke se ne izgubijo več pri izvozu
  Majhno, ploščato besedilo je pri izvozu STL, 3MF ali OBJ izgubilo posamezne črke, tanko besedilo večino: pičko na i-ju, opuščaj, male črke. Izvoz jih je imel za ostružke, ki jih je pustil rez. To zdaj velja samo za telesa, ki jih je spremenil rez, združitev več teles ali ločitev barv.
• SVG z dotikajočimi se oblikami pride celoten
  V narisani ali posneti sliki se dve obliki pogosto stikata v samo eni točki. Uvoz je takrat nekatere oblike izpustil, slika pa je prišla manjša in z luknjami. Take oblike se zdaj sestavijo skupaj in slika ostane cela.
• Posnetek + zaobljenje na valju je spet pri nogi
  Posnetek + zaobljenje na spodnjem robu valja je prišel napačno obrnjen: zaobljenje pri nogi, posnetek nad njim, zaobljen pa je bil tudi zgornji rob. Zdaj posnetek leži na plošči in se prelije v steno, zgornji rob ostane nedotaknjen.
• Vnos japonščine in kitajščine v polje Besedilo
  Z vnosno metodo (IME) v polje Besedilo pri besedilu ali imenski tablici ni bilo mogoče vtipkati ničesar smiselnega: »ishi« je postalo »いｓｈい« in ga ni bilo mogoče pretvoriti v kanji. Polje zdaj ohrani vtipkano in besedo prevzame, ko je končana. To velja za japonščino, kitajščino in korejščino.
• Interaktivna pomoč razloži vsako nastavitev posebej
  V nastavitvah delovnega prostora je klik z interaktivno pomočjo pogosto vodil le do dolgega razdelka ali nikamor. Zdaj ima navodilo za vsako skupino nastavitev svoj razdelek (angleško in nemško), poleg tega še »Izbira barv« za barvno kartico, polja, drsniki, barvni gumbi in seznami pa najdejo svoj razdelek, tudi stikalo Hitri način.
• Pogled zgodovine pove, kaj puščici razveljavita in uveljavita
  Pod drsnikom pogleda zgodovine vrstica zdaj poimenuje korak, ki bi ga razveljavila leva puščica (»Zadnji korak: Premaknjeno Škatla«), in tistega, ki bi ga uveljavila desna (»Naslednji korak: 2 predmeta združena v skupino«), pri najstarejšem in najnovejšem stanju pa »ni«. Deluje tudi za osnutke, shranjene prej.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.92.0) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.92.0) s slovenskim vmesnikom.

v1.91.0

What's new in 1.91.0

• Ctrl and the arrow keys pan the view
  With nothing selected, hold Ctrl (Cmd on a Mac) and press the arrow keys to slide the view across the screen: a tenth of the picture a press, half of it with Shift as well. The plain arrow keys still turn the view.
• Raised floor for Gridfinity bins
  A Gridfinity bin can now have a raised floor: set "Floor height" in the Properties panel, and the bin is solid up to it, a blank to cut the shapes of your tools into.
• The cut face follows the plane without lag
  The filled cut face of the section view lagged behind the plane while you dragged it and only came back when your hand rested. Now it is cut for the newest position of the plane at every step.
• Folders for custom shapes
  Custom shapes can be sorted into folders, up to three levels deep, in the browser and on the server. A folder has a counter and can be renamed and deleted (after asking), and a shape is put into a folder when you save it or moved to another one afterwards.
• A loose hole is no longer lost in the export
  A hole you had not grouped was missing from the STL, 3MF or OBJ file when the body it cuts from touched or overlapped another body of the same colour. The material estimate then counted it as solid too. The hole now stays.

---

Kaj je novega v 1.91.0

• Ctrl in smerne tipke premikajo pogled
  Ko ni nič izbrano, drži Ctrl (Cmd na Macu) in pritiskaj smerne tipke, da pogled zdrsne po zaslonu: z vsakim pritiskom za desetino slike, s Shiftom še za polovico. Same smerne tipke pogled še vedno vrtijo.
• Dvignjeno dno za posode Gridfinity
  Posoda Gridfinity lahko zdaj dobi dvignjeno dno: v oknu lastnosti nastaviš »Višina dna« in posoda je do nje polna, kot surovec, v katerega izrežeš oblike svojih orodij.
• Prerezana ploskev sledi ravnini brez zaostajanja
  Zapolnjena prerezana ploskev pogleda prereza je med vlečenjem ravnine zaostajala in se je vrnila šele, ko je roka mirovala. Zdaj je ob vsakem koraku izrezana za najnovejši položaj ravnine.
• Mape za lastne oblike
  Lastne oblike je mogoče razvrstiti v mape, do tri ravni globoko, v brskalniku in na strežniku. Mapa ima števec, jo je mogoče preimenovati in izbrisati (po vprašanju), oblika pa gre v mapo ob shranjevanju ali pa jo pozneje premakneš v drugo.
• Prosta luknja se ne izgubi več pri izvozu
  Luknja, ki je nisi združil v skupino, je manjkala v datoteki STL, 3MF ali OBJ, kadar se je telo, iz katerega reže, dotikalo drugega telesa iste barve ali se z njim prekrivalo. Ocena materiala jo je zato štela kot polno. Luknja zdaj ostane.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.91.0) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.91.0) s slovenskim vmesnikom.

v1.90.0

What's new in 1.90.0

• QR codes in the shape library
  The new QR code entry turns a text or a web address into a code to print: alone, raised on a plate in two colours, or engraved into the plate. Error correction, width and quiet zone can be chosen, the preview shows the code first, and a warning appears when the modules get too small for a readable print. You can change the text later in the properties and make the code again.
• The mouse wheel changes numbers in the tool panels too
  What already worked in the properties of a shape works now in Chamfer, Fillet, Hollow, Pattern, Hole pattern, Face, Mate faces, Split and the Section view menu: click into the number field, then the mouse wheel changes the value. Ten times as much with Shift, a tenth with Ctrl, a hundredth with Alt.
• The cut face follows the plane
  The filled cut face of the section view no longer waits until the plane stands still: it follows the plane while you move it, so the body no longer looks hollow for a moment.
• Notes stay with their bodies in groups
  Group takes a pinned note into the group, Ungroup hands it to the visible part under it, and while a group is open for editing its notes move with the part they sit on. A note whose body is deleted stays where it stood.
• Finger scoops for Gridfinity bins
  A Gridfinity bin of 2 height units or more can now have a finger scoop along any of its inner walls, several at once: the floor rises along a quarter circle into the wall, so small parts can be pushed out. You set the radius in the Properties panel.
• Half-size grid for Gridfinity bins
  A Gridfinity bin can now be built in cells of 21 mm, each with a foot of its own; four of them stand in one socket of an ordinary baseplate. So bins of 1½ or 2½ units fit beside whole ones. You switch on "Half-size grid (21 mm)" in the Properties panel.
• The revolve sketch shows the front view when edited again
  When you open the sketch of a revolved body again to edit it, it shows the other bodies from the front, in the same view as the profile, as while you draw it. Before, the view from above came back as soon as the body stood above the plate.
• Angles with two decimals
  A rotation is now kept with two decimals and shown in the number field: 11.25° stays 11.25°, also when you turn with Shift on the rotation circle. Before, it became 11.3°, and the field showed whole degrees.
• The chamfer slider moves in tenths of a millimetre
  The slider for the distance or radius of a chamfer or fillet now moves in tenths of a millimetre up to 10 mm instead of giving odd values like 2.347. Larger or more exact values you type into the field.
• Pockets of a whole depth can be chamfered
  When a hole ends exactly on a face of the body, for example with a height of 5.000 pulled through a workplane on a slope, a chamfer on the rim of the pocket failed. The pocket is now cut cleanly when grouped, and the chamfer works.
• Custom shapes take their notes along
  If you save bodies with pinned notes as a custom shape, the notes come along when you put the shape into a design. They appear closed, pinned to the new bodies, with new numbers.

---

Kaj je novega v 1.90.0

• Kode QR v knjižnici oblik
  Nov vnos Koda QR iz besedila ali spletnega naslova naredi kodo za tiskanje: samostojno, privzdignjeno na plošči v dveh barvah ali vgravirano v ploščo. Popravljanje napak, širina in mirno območje so izbirni, predogled kodo pokaže vnaprej, opozorilo pa se pojavi, ko so moduli premajhni za berljiv tisk. Besedilo lahko pozneje spremeniš v lastnostih in kodo ustvariš znova.
• Kolesce miške spreminja številke tudi v oknih orodij
  Kar je že delovalo v lastnostih oblike, zdaj deluje tudi pri Posnetku, Zaobljenju, Izdolbi, Vzorcu, Vzorcu lukenj, Ploskvi, Prilagajanju ploskev, Razdelitvi in v meniju prereza: klikni v številčno polje, nato kolesce miške spreminja vrednost. S Shiftom desetkrat toliko, s Ctrl desetinko, z Alt stotinko.
• Prerezana ploskev sledi ravnini
  Zapolnjena prerezana ploskev pogleda prereza ne čaka več, da se ravnina ustavi: med premikanjem ravnine teče z njo, tako da telo ni več za trenutek videti votlo.
• Opombe v skupinah ostanejo na svojih telesih
  Združi v skupino prikovano opombo vzame v skupino, Razdruži jo preda vidnemu delu pod njo, in dokler je skupina odprta za urejanje, se njene opombe premikajo z delom, na katerem so. Opomba, katere telo izbrišeš, ostane, kjer je stala.
• Žlebovi za prste pri posodah Gridfinity
  Posoda Gridfinity z višino vsaj 2 enoti lahko zdaj dobi žleb za prste ob vsaki notranji steni, tudi ob več hkrati: dno se ob steni dvigne po četrtini kroga, da se majhni deli lažje potisnejo ven. Polmer nastaviš v oknu lastnosti.
• Polovična mreža za posode Gridfinity
  Posodo Gridfinity je zdaj mogoče zgraditi v celicah po 21 mm, vsaka s svojo nogo; štiri stojijo v enem ležišču običajne osnovne plošče. Tako se poleg celih posod prilegajo tudi posode velikosti 1½ ali 2½ enote. »Polovična mreža (21 mm)« vklopiš v oknu lastnosti.
• Skica vrtenja ob ponovnem urejanju spet pokaže pogled od spredaj
  Ko skico zavrtenega telesa znova odpreš za urejanje, druga telesa spet pokaže od spredaj, v istem pogledu kot profil, kot med risanjem. Prej se je pogled od zgoraj vrnil, takoj ko je telo stalo nad ploščo.
• Koti z dvema decimalkama
  Zasuk se zdaj shrani z dvema decimalkama in je tako prikazan v številčnem polju: 11,25° ostane 11,25°, tudi ko vrtiš s Shiftom na krogu vrtenja. Prej je postalo 11,3°, polje pa je kazalo cele stopinje.
• Drsnik pri posnetku se premika po desetinkah milimetra
  Drsnik za razdaljo ali polmer pri posnetku in zaobljenju zdaj skače po desetinkah milimetra do 10 mm, namesto da bi dajal nenavadne vrednosti, kot je 2,347. Večje ali natančnejše vrednosti vtipkaš v polje.
• Žepe s polno globino je mogoče posneti
  Kadar se vdolbina konča natanko na ploskvi telesa, na primer z višino 5,000, povlečeno skozi delovno ravnino na nagibu, posnetek na robu žepa ni uspel. Žep se zdaj ob združevanju v skupino čisto izreže, posnetek pa deluje.
• Lastne oblike vzamejo opombe s seboj
  Če telesa s prikovanimi opombami shraniš kot lastno obliko, opombe pridejo zraven, ko obliko vstaviš v osnutek. Pojavijo se zaprte, prikovane na nova telesa, z novimi številkami.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.90.0) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.90.0) s slovenskim vmesnikom.

v1.89.0

What's new in 1.89.0

• An exported OBJ stands upright in the slicer
  STL and 3MF were already written with Z up, but the OBJ with Y up, and slicers such as Cura showed such a part lying on its side. Now the OBJ is written with Z up, too. layerling's own import still stands such files upright.
• layerling now speaks Japanese
  The whole interface is there in Japanese, written for upper primary school children and their teachers, with Tinkercad's Japanese terms where it has them. The guide chapters are still in English. You choose the language in the language menu.
• Folders for your designs
  On the start page, “New folder” makes folders, folders in folders too. Drag designs into them or use “Move to …” in a design's menu. Deleting a folder deletes no design, and “Back up all” keeps the folders.
• History view: open a group and bring back its parts
  In the History view you can now open a group (the Open group button or the E key): its parts then lie there one by one, and you bring back one or more of them without taking the whole group. Groups inside groups work the same way, and Back out closes one level.
• iPad: a lost finger no longer locks the editor
  On an iPad it could happen that after tapping two objects one after the other nothing answered until the page was reloaded: the editor believed a finger was still down whose end it had never heard of, and took every further touch for a second finger. Now every new first finger starts the count afresh, and leaving the app resets it, too.
• Chamfillet: the printable foot
  In the chamfer window you now choose at the top between Chamfer and Chamfillet. The second kind puts a chamfer at the plate on the bottom edges that blends tangentially into a fillet toward the wall: the first layers need no support, and the edge still ends soft. Bottom edges picks the whole foot in one click; the AI connection can do it too (kind chamfillet).
• The two-finger zoom on the trackpad now works in the sketch too
  On a Mac with Safari, spreading and pinching on the trackpad in the sketch zoomed the whole page instead of the drawing plate. Now it zooms the sketch, towards the fingers, at the speed of the settings, as in the 3D window. Restart the app once afterwards.
• Chamfer and Fillet on a group start faster the second time
  A group that already holds filleted or chamfered parts had to be turned from its mesh back into an exact body every time the Chamfer or Fillet tool started, about ten seconds for a pocket in a filleted body. Now layerling keeps the result as long as the mesh stays the same: cancelling and starting again, or Undo and Redo, takes a third of the time. The first time takes as long as before.
• Changing the height of a turned body no longer makes it wander
  A turned body, a pocket on a sloped workplane for instance, slid along the plane when its height was changed in the Properties panel, because its centre only moved straight up. Now the middle of its base stays where it was and the body grows or shrinks only in its own direction. The AI connection's command does the same.
• On a phone your designs are right at the top
  On a narrow screen the saved designs of the start page lay more than a screen down, behind three big tiles and the backup note. Once there are designs, the three tiles are now one short row and the backup note stands behind the designs. On a computer, and with no designs yet, everything stays as it was.
• A pinned shape library is there again at the next start
  Anyone who had pinned the shape library found only the pin again at the next start: it was still set, but the library itself was closed. Now a pinned library opens by itself when the editor starts, where you left it.
• Fillet and Chamfer: several quick buttons, Horizontal edges, and the window stays open
  The Fillet and Chamfer window has a new Horizontal edges button. With Shift or Ctrl and a click you add the edges of a quick button to the selection, Top and Bottom edges together for example. And after Apply the window stays open on the new body, with the same size and no edge picked, so you can set the next fillet with another size at once. Done, Esc or the cross closes it.
• The revolve sketch shows the other bodies from the front and puts the body where you drew the profile
  In the revolve sketch the other bodies used to show from above, as flat outlines, while the profile is a side view, so the two could not be lined up. Now you see them from the front, in the same view as the profile, with the axis in the middle. And the body is made where you drew the profile: the horizontal line through the middle is the ground, and a profile above a plate gives a body that stands on it. This holds on the base plate.

---

Kaj je novega v 1.89.0

• Izvožen OBJ v razrezovalniku stoji pokonci
  STL in 3MF sta bila že zapisana z osjo Z navzgor, OBJ pa z osjo Y navzgor, zato so razrezovalniki, kot je Cura, tak del prikazali ležečega. Zdaj tudi OBJ zapiše Z navzgor. Layerlingov lasten uvoz take datoteke še vedno postavi pokonci.
• Layerling zdaj govori japonsko
  Ves vmesnik je na voljo v japonščini, napisan za otroke višjih razredov osnovne šole in njihove učitelje, z Tinkercadovimi japonskimi izrazi, kjer jih ta ima. Poglavja navodil so še v angleščini. Jezik izbereš v meniju jezikov.
• Mape za tvoje osnutke
  Na začetni strani »Nova mapa« ustvari mape, tudi mape v mapah. Osnutke povleci vanje ali uporabi »Premakni v …« v meniju osnutka. Brisanje mape ne izbriše nobenega osnutka, »Varnostno kopiraj vse« pa mape vzame zraven.
• Pogled zgodovine: odpri skupino in vrni njene dele
  V pogledu zgodovine zdaj lahko odpreš skupino (gumb »Odpri skupino« ali tipka E): njeni deli ležijo posamično in enega ali več jih vrneš, ne da bi vzel celotno skupino. Skupine v skupinah delujejo enako, »Nazaj« zapre eno raven.
• iPad: izgubljen prst urejevalnika ne zaklene več
  Na iPadu se je lahko zgodilo, da po dotiku dveh predmetov zapored nič več ni odzivalo, dokler nisi ponovno naložil strani: urejevalnik je mislil, da je en prst še na zaslonu, njegovega konca pa nikoli ni zaznal, in vsak naslednji dotik je štel za drugi prst. Zdaj se z vsakim novim prvim prstom štetje začne znova, ponastavi pa se tudi ob zapustitvi aplikacije.
• Posnetek + zaobljenje: tiskljiva noga
  V oknu za posnetje zdaj zgoraj izbereš med »Posnetek« in »Posnetek + zaobljenje«. Druga vrsta na spodnjih robovih naredi posnetek ob plošči, ki se tangentno prelije v zaobljenje proti steni: prve plasti ne potrebujejo podpor, rob pa se kljub temu konča mehko. »Spodnji robovi« izberejo celotno nogo z enim klikom; deluje tudi prek povezave z umetno inteligenco (kind »chamfillet«).
• Povečava z dvema prstoma na sledilni ploščici zdaj deluje tudi v skici
  Na Macu s Safarijem je razmik in približevanje prstov na sledilni ploščici v skici povečal celotno stran namesto risalne plošče. Zdaj poveča skico, proti prstom, s hitrostjo iz nastavitev, kot v 3D oknu. Nato aplikacijo enkrat znova zaženi.
• Posnetek in zaobljenje na skupini se drugič zaženeta hitreje
  Skupino, ki že vsebuje zaobljene ali posnete dele, je bilo treba ob vsakem zagonu orodja za posnetek ali zaobljenje iz mreže spet preračunati v natančno telo, pri žepu v zaobljenem telesu okoli deset sekund. Zdaj si Layerling rezultat zapomni, dokler se mreža ne spremeni: prekinitev in ponovni zagon ali razveljavitev in uveljavitev trajata tretjino časa. Prvič traja enako dolgo kot prej.
• Višina zavrtenega telesa ga ne premika več
  Zavrteno telo, na primer vdolbina na nagnjeni delovni ravnini, je ob spremembi višine v oknu lastnosti zdrsnilo vzdolž ravnine, ker se je njegova sredina premaknila le navpično navzgor. Zdaj sredina njegove osnovne ploskve ostane, kjer je bila, telo pa raste ali se krči samo v svoji smeri. Enako velja za ukaz povezave z umetno inteligenco.
• Na telefonu so tvoji osnutki takoj zgoraj
  Na ozkem zaslonu so bili shranjeni osnutki na začetni strani več kot zaslon nižje, za tremi velikimi ploščicami in opozorilom o varnostnem kopiranju. Ko osnutki obstajajo, so tri ploščice zdaj ena kratka vrstica, opozorilo pa je za osnutki. Na računalniku in brez osnutkov ostane vse po starem.
• Pripeta knjižnica oblik je ob naslednjem zagonu spet tam
  Kdor je knjižnico oblik pripel, je ob naslednjem zagonu našel le buciko: še vedno je bila nastavljena, knjižnica sama pa zaprta. Zdaj se pripeta knjižnica ob zagonu urejevalnika odpre sama, tam, kjer si jo pustil.
• Posnetek in zaobljenje: več hitrih gumbov, vodoravni robovi in okno ostane odprto
  Okno za zaobljenje in posnetek ima nov gumb »Vodoravni robovi«. Z Shift ali Ctrl in klikom robove hitrega gumba dodaš izbiri, na primer zgornje in spodnje robove skupaj. Po »Uporabi« okno ostane odprto na novem telesu, z enako velikostjo in brez izbranih robov, da lahko takoj narediš naslednje zaobljenje z drugo mero. »Končano«, Esc ali križec ga zapre.
• Skica vrtenja prikazuje druga telesa od spredaj in postavi telo tja, kamor si narisal profil
  V skici vrtenja so bila druga telesa doslej prikazana od zgoraj, kot ploščati obrisi, profil pa je stranski pogled, zato obojega ni bilo mogoče poravnati. Zdaj jih vidiš od spredaj, v istem pogledu kot profil, z osjo na sredini. Telo nastane tam, kjer si narisal profil: vodoravna črta skozi sredino je tla, profil nad ploščo pa da telo, ki stoji na njej. To velja na osnovni plošči.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.89.0) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.89.0) s slovenskim vmesnikom.

v1.88.0

What's new in 1.88.0

• A group with a fillet or chamfer can be ungrouped again
  Ungroup stayed grey as soon as a group had got a fillet or chamfer. Now the button takes the edge features back first and then dissolves the group, in one step that Ctrl+Z undoes. And the Fillet or Chamfer tool stays open when you take a feature back.
• The section view fills the cut face
  In the section view the cut was left open, and a solid and a hole looked the same inside. Where the plane goes through a body, the cut is now filled with its colour, a little darker, and a hole inside it stays empty. The filled face appears a moment after the plane stops moving.
• The edge window shows which quick button made the selection
  In the Fillet and Chamfer window the quick buttons were too wide and gave the window a small sideways scroll bar; they wrap now. The buttons react when the pointer is over them, and the quick button whose edges are picked now (All sharp, Top, Bottom or Vertical edges) stays highlighted.
• Japanese letters in texts and name tags
  A Japanese name on a text or a name tag used to come out as question marks, because the built-in typefaces have no kana and no kanji. There is now a Japanese typeface that lends its characters to every other typeface and to fonts of your own. It is fetched only when a text has Japanese letters, and is there offline afterwards.
• A long press on an iPad no longer starts a text selection
  On an iPad a long press could start the system's text selection, for example on a word in the menu or in the toolbar. After that the touches went to the selection and no longer to layerling, and it looked as if an object stayed in edit mode. The editor can no longer be selected, but input fields can.
• The shape library opens where you left it
  A shape library that had been pulled narrow and placed at the right edge opened far to the left the next time, as if an invisible edge held it back. It now opens at the remembered spot, also at a size of its own.
• Erasing in the sketch: the button erases the selection, and the tool takes a window
  With several points and lines selected, the Erase button did not erase them, it only dropped the selection. Now it erases the selection. And with the Erase tool you can drag a window over several points and lines: everything inside is erased.
• The ruler has a scale in inches
  With the unit set to inches (the switch at the bottom right), the ruler carries a scale in inches: a line every sixteenth of an inch, with the whole inches numbered. In millimetres everything stays as it was.
• A chain of lines in the sketch is easier to end
  When drawing with Line, Bézier curve or Smooth curve, a right click without moving now ends the chain, and so does a double click on the last point; the tool stays selected. A right click that you use to pan the view does not end it. To close the shape you still click the first point.
• The mouse wheel changes a number in a clicked field
  When you click into a number field of the properties, the mouse wheel changes the value: one unit a notch, ten times as much with Shift, a tenth with Ctrl and a hundredth with Alt. A field that you have not clicked lets the panels scroll as before.
• Label shelves for Gridfinity bins
  A Gridfinity bin of 3 height units or more can now have a shelf for a label along any of its inner walls, several at once. It sits just under the stacking lip, and you set its width, length and the rounded or chamfered corners in the Properties panel.
• A sketch can be mirrored
  Select points and lines in the sketch and click Mirror in the bar: across the vertical axis (left-right), the horizontal one (top-bottom) or a straight line of the sketch that you click. The copy lands on the other side and nothing is linked. Points on the axis are shared, so a half shape becomes one closed outline.
• Interactive Help hits better inside the tool windows
  Cancel, Apply, fields and sliders in a tool window now ask about the tool itself, for example "Chamfer edges", instead of a word that the guide writes a hundred times. The shape library, the object list and the Export window answer with their section, as do the view cube and the camera bar between their buttons.

---

Kaj je novega v 1.88.0

• Skupino z zaobljenjem ali posnetkom je spet mogoče razdružiti
  Gumb »Razdruži« je ostal siv, takoj ko je skupina dobila zaobljenje ali posnetek. Zdaj gumb najprej odstrani lastnosti robov in nato razdruži skupino, v enem koraku, ki ga Ctrl+Z razveljavi. Orodje za zaobljenje in posnetek ostane odprto, ko lastnost odstraniš.
• Prerez zapolni prerezano ploskev
  V prerezu je bil rez odprt, trdno telo in luknja pa sta znotraj izgledala enako. Kjer ravnina seka telo, je rez zdaj zapolnjen z njegovo barvo, malo temnejšo, luknja v njem pa ostane prazna. Zapolnjena ploskev se pokaže trenutek po tem, ko se ravnina neha premikati.
• Okno za robove pokaže, kateri hitri gumb je naredil izbor
  V oknu za zaobljenje in posnetek so bili hitri gumbi preširoki in so okno naredili z majhnim stranskim drsnikom; zdaj se prelomijo v novo vrstico. Gumbi se odzovejo, ko je kazalec nad njimi, hitri gumb, katerega robovi so zdaj izbrani (Vsi ostri robovi, Zgornji, Spodnji ali Navpični robovi), pa ostane poudarjen.
• Japonske črke v besedilih in imenskih tablicah
  Japonsko ime na besedilu ali imenski tablici je prej izpadlo kot vprašaji, ker vgrajene pisave nimajo kane in kanjija. Zdaj je na voljo japonska pisava, ki svoje znake posodi vsem drugim pisavam in tudi tvojim lastnim. Prenese se samo, ko ima besedilo japonske črke, potem pa je na voljo tudi brez povezave.
• Dolg pritisk na iPadu ne začne več označevanja besedila
  Na iPadu je dolg pritisk lahko začel sistemsko označevanje besedila, na primer pri besedi v meniju ali v orodni vrstici. Potem so dotiki šli v označevanje in ne več v layerling, videti pa je bilo, da predmet ostane v urejanju. Urejevalnika ni več mogoče označiti, polja za vnos pa še vedno.
• Knjižnica oblik se odpre tam, kjer si jo pustil
  Knjižnica oblik, ki si jo povlekel ozko in postavil ob desni rob, se je naslednjič odprla daleč na levi, kot da jo drži nevidni rob. Zdaj se odpre na zapomnjenem mestu, tudi v lastni velikosti.
• Brisanje v skici: gumb zbriše izbor, orodje pa vzame okno
  Pri več izbranih točkah in črtah gumb »Pobriši« ni brisal, samo spustil je izbor. Zdaj zbriše izbor. Z orodjem »Pobriši« pa lahko povlečeš okno čez več točk in črt: vse znotraj se zbriše.
• Ravnilo ima merilo v palcih
  Ko je enota nastavljena na palce (stikalo spodaj desno), ima ravnilo merilo v palcih: črto na vsako šestnajstino palca, cele palce pa označene s številkami. V milimetrih ostane vse, kot je bilo.
• Verigo črt v skici je lažje končati
  Pri risanju z orodjem »Daljica«, »Bézierova krivulja« ali »Gladka krivulja« desni klik brez premikanja zdaj konča verigo, prav tako dvoklik na zadnjo točko; orodje ostane izbrano. Desni klik, ki ga uporabiš za premikanje pogleda, je ne konča. Za zaprtje oblike še vedno klikneš prvo točko.
• Miškino kolesce spremeni število v kliknjenem polju
  Ko klikneš v številčno polje lastnosti, miškino kolesce spremeni vrednost: ena enota na klik, desetkrat toliko s Shiftom, desetinko s Ctrl in stotinko z Alt. Polje, v katero nisi kliknil, pusti, da se plošče drsijo kot prej.
• Police za nalepke pri posodah Gridfinity
  Posoda Gridfinity z višino 3 enote ali več lahko zdaj dobi polico za nalepko ob poljubni notranji steni, tudi več hkrati. Stoji tik pod obrobo za zlaganje, njeno širino, dolžino in zaobljene ali posnete vogale pa nastaviš v lastnostih.
• Skico je mogoče zrcaliti
  V skici izberi točke in črte ter v vrstici klikni »Zrcali«: čez navpično os (levo-desno), vodoravno (zgoraj-spodaj) ali čez ravno črto skice, ki jo klikneš. Kopija pristane na drugi strani in ni nič povezano. Točke na osi so skupne, zato je pol oblike eden sklenjen obris.
• Interaktivna pomoč bolje zadene znotraj orodnih oken
  »Prekliči«, »Uveljavi«, polja in drsniki v orodnem oknu zdaj sprašujejo po orodju samem, na primer »Posnemi robove«, namesto po besedi, ki jo vodnik napiše stokrat. Knjižnica oblik, seznam objektov in okno za izvoz odgovorijo s svojim razdelkom, prav tako kocka pogleda in vrstica kamere med svojimi gumbi.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.88.0) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.88.0) s slovenskim vmesnikom.

v1.87.0

What's new in 1.87.0

• A copy can be moved with the mouse and copied again
  After duplicating, the copy lies exactly on the original. A mouse press on it sometimes hit the original instead of the selected copy, and the original moved. That broke the chain that lets the next duplicate carry on by the same step (for a row of holes, say), and the next copy stayed where it was. Where bodies lie exactly on one another, the one that is already selected now wins.
• "Save as default" keeps the colour, too
  Colour a shape, a cylinder for example, and press "Save as default" in the Properties panel: every new cylinder then starts in that colour, and the other kinds keep their own. "Reset defaults" gives the app's colour back. Also, a second save or reset in the same design did not reach new shapes; that is fixed.
• A typed measure also counts when you click beside the box
  If you typed a number into a measure box on a body (or into the angle box) and click on empty space with the left mouse button, layerling now applies the number, as the right click already did. Before, a left click lost it. Esc still cancels.
• Align: the handles keep apart
  On small parts the handles of Align lay so close that you could not click them one by one, and zooming far in made them disappear. Now the three handles of an axis keep a minimum distance, and handles that are still in front of the camera stay visible when you zoom.
• Arrow keys: the view follows only when needed
  The arrow keys move a body, and the view goes along when it would otherwise leave the picture. Before, it also went along when the body already lay at the edge or outside, after zooming in far for example: then the body stood still and everything else slid past. Now the view goes along only when the body is in the picture and would leave it.
• Fillet and chamfer: “Bottom edges”
  Next to “Top edges”, the Fillet and Chamfer tools now have “Bottom edges”: one click picks only the edges along the very bottom of the body, such as the foot of a part. That rounds or chamfers just the lower end without clicking the edges one by one. The AI connection understands it too (“bottom”).
• The height value also stands at the height handle
  When you pulled the top middle handle, the height value stood only at the vertical edge, often far from the handle, and it vanished when you zoomed in. Now it also stands right at the handle (above it, below the lower handle), always in view, and can be clicked there to type a number. The measure at the edge stays as it was.
• The hide button stays when several bodies are selected
  In the properties window the button with the eye disappeared as soon as more than one body was selected, and you had to use the Visibility menu. Now it stands beside the lock for several bodies too: it hides all the selected ones, and when all of them are hidden it shows them again. Ctrl+H does the same.
• Hidden shapes can be seen now
  When shapes are hidden, a small number sits on the button of the Visibility group; a click on it shows them all again. If you open a design that has hidden shapes, a message tells you once, with a button “Show all”. Hidden shapes stay hidden if you do nothing.
• The Crescent is closed and no longer comes out hollow
  The two lids of the Crescent faced the wrong way against its walls. A slicer therefore took the place where it overlaps another body for a hole, and in the export it could not be merged with other bodies. The mesh is closed now, and the Crescent behaves like any other shape.
• The AI can save the project as a .lyl
  Through the MCP connection an AI could write STL, 3MF and OBJ to a path, but not the editable design. The new tool layerling_save_project saves the whole design as a .lyl file at a path on the computer of the MCP server, without a dialog. An existing file is only replaced when you say so, and the target of Ctrl+S in the editor stays as it was.
• The user guide is now also in Polish
  All 17 chapters of the guide are translated into Polish, and the buttons are named in it exactly as in the Polish interface. The search (Ctrl+K and the search in the guide) now also finds words with "ł" when you type "l". Two sentences in the guide showed a raw "{count}" in every language; that is fixed.
• The list of shortcuts can be printed
  The window with the keyboard shortcuts, in the editor and in sketch mode alike, has a printer button next to the question mark. It prints only the list, black on white and in large type. In the print dialog of the browser you can also save it as a PDF. Ctrl+P while the window is open does the same.
• A hovering Apple Pencil shows the names of buttons
  On an iPad layerling now shows the name of a button or field in a small bubble when the Apple Pencil rests above it for a moment, as a mouse shows a tooltip. This works on iPads whose Pencil can hover.
• Tapered, turned cylinders keep their turn when grouped
  A cylinder with a taper or a lean that you had turned by 90 degrees came out unturned when grouped (and when exported), so the group had other measures than its parts. The turn is kept now.
• The grid can be reset to the standard
  If the grid colour was set so that no grid can be seen any more, one click brings it back: at the end of the Workplane page in the settings, “Reset grid” puts visibility, colours, spacing and line weight back to the standard, for the design and for the default saved with “Make default”. The plate's size and printer stay as they are.
• The shape library can be pulled to any size
  The edges and corners of the shape library pull its width and height, as large or small as your screen needs; the browser remembers the size. When the library is narrow, it shows only the pictures without names, and the name is in the tooltip.
• The ruler can be pulled to 500 mm by its handles
  The handles of the ruler stopped at the size of the plate, at least 220 mm, while its slider went up to 500 mm. Now the handles reach as far as the slider does.
• Colours of your own can be kept for good
  The colours you mix yourself were already listed under “Recently used”, but only eight, and the oldest dropped out. The pin in the new row “Kept” holds the colour you have chosen: it stands in a row of its own, newer colours never push it out, and the same pin lets go of it again. Up to 21 colours are kept in this browser.
• The Text shape gets a letter edge
  In the Text properties you can round or chamfer the top edge of the letters, with a size of up to 5 mm, as on a name tag. A rounding goes as far as the strokes are wide, and the underside stays flat.
• The view can be panned to parts beside the plate
  If you had parked parts far beside the plate, the mouse could not take the view over to them: the point the view pans and turns around stayed on the plate, except after “Center view on selection”. It now reaches the farthest body of the design.
• The shape library no longer meets an invisible edge when moved
  With a small or large toolbar the shape library stopped short of the window's edge when moved, or ran out of the window on the right and below. Now it goes as far as the window's edge at every toolbar size.

---

Kaj je novega v 1.87.0

• Kopijo lahko premakneš z miško in jo znova podvojiš
  Po podvajanju kopija leži natanko na izvirniku. Klik z miško nanjo je včasih zadel izvirnik namesto izbrane kopije in izvirnik se je premaknil. S tem se je prekinila veriga, ki naslednje podvajanje premakne za isti odmik (na primer za vrsto lukenj), in naslednja kopija je ostala na mestu. Zdaj pri telesih, ki ležijo natanko eno na drugem, prednost dobi že izbrano.
• »Shrani kot privzeto« si zapomni tudi barvo
  Obarvaj obliko, na primer valj, in v oknu z lastnostmi pritisni »Shrani kot privzeto«: vsak nov valj se bo začel s to barvo, druge vrste obdržijo svoje. »Ponastavi privzeto« vrne barvo programa. Popravljeno je tudi, da drugo shranjevanje ali ponastavitev v istem projektu pri novih oblikah ni imelo učinka.
• Vtipkana mera velja tudi ob kliku mimo polja
  Če si v polje z mero na telesu (ali v polje za kot) vtipkal število in z levim gumbom miške klikneš v prazno, ga layerling zdaj sprejme, tako kot je že pri desnem kliku. Prej se je ob levem kliku izgubilo. Esc še vedno prekliče.
• Poravnaj: ročice ostanejo narazen
  Pri majhnih delih so ročice orodja »Poravnaj« ležale tako blizu, da si jih ni bilo mogoče posamično klikniti, pri močnem približevanju pa so izginile. Zdaj tri ročice ene osi ohranjajo najmanjšo razdaljo, ročice, ki so še pred kamero, pa ostanejo vidne tudi pri približevanju.
• Puščične tipke: pogled sledi samo, kadar je treba
  Puščične tipke premikajo telo, pogled pa gre zraven, če bi telo sicer zapustilo sliko. Prej je sledil tudi, ko je bilo telo že na robu ali zunaj, na primer po močnem približevanju: telo je stalo, vse drugo pa je drselo mimo. Zdaj pogled sledi le, če je telo v sliki in bi jo zapustilo.
• Zaobli in posnemi: »Spodnji robovi«
  Ob »Zgornji robovi« imata orodji za zaobljenje in posnetje zdaj tudi »Spodnji robovi«: en klik izbere samo robove čisto na dnu telesa, na primer nožico dela. Tako zaobliš ali posnameš samo spodnji konec, ne da bi robove klikal posamično. Razume ga tudi povezava z umetno inteligenco (»bottom«).
• Vrednost višine je tudi ob ročici za višino
  Ko si vlekel zgornjo srednjo ročico, je bila vrednost višine le ob navpičnem robu, pogosto daleč od ročice, pri približevanju pa je izginila. Zdaj je dodatno tudi tik ob ročici (nad njo, pri spodnji ročici pod njo), vedno v sliki, in jo lahko tam klikneš ter vtipkaš število. Mera ob robu ostane, kot je bila.
• Gumb za skrivanje ostane pri več izbranih telesih
  V oknu z lastnostmi je gumb z očesom izginil, takoj ko je bilo izbrano več kot eno telo, in bilo je treba uporabiti meni »Vidnost«. Zdaj je ob ključavnici tudi pri več telesih: skrije vsa izbrana, če pa so ...

v1.86.2

What's new in 1.86.2

• A number at the mouse pointer counts the selection
  When you select several bodies with Shift, a small number now stands below the mouse pointer while Shift is held and two or more bodies are selected. While clicking you keep the tally in view without glancing at the Properties panel. Mouse only: a finger would cover the number.
• Interactive Help also answers for greyed-out buttons
  With a greyed-out button, such as "Center view on selection" while nothing is selected, Interactive Help stayed silent. Now it answers there too and leads to the matching section of the guide, so you can read what the button is for and why it does not work at the moment.
• The shape library can be moved and kept open
  The shape library covered the spot you aim at while placing. Now you move it by its title bar, over the Properties panel for example; a double-click on the title bar puts it back under its button. The pin in the title bar keeps it open when you want to put several shapes one after the other. Without the pin it closes after each shape, as it did. The same goes for the shapes of the sketch.

---

Kaj je novega v 1.86.2

• Število ob kazalcu miške šteje izbor
  Ko z Shiftom izbereš več teles, pod kazalcem miške zdaj stoji majhno število, dokler držiš Shift in sta izbrani dve telesi ali več. Med klikanjem imaš seštevek pred očmi, ne da bi pogledal v ploščo Lastnosti. Samo z miško: prst bi število zakril.
• Interaktivna pomoč odgovori tudi pri zatemnjenih gumbih
  Pri zatemnjenem gumbu, na primer »Osredini pogled na izbor«, ko ni nič izbrano, je Interaktivna pomoč molčala. Zdaj odgovori tudi tam in vodi v ustrezen razdelek vodnika, da prebereš, čemu gumb služi in zakaj trenutno ne deluje.
• Knjižnico oblik je mogoče premikati in imeti odprto
  Knjižnica oblik je pokrivala mesto, na katero ciljaš pri postavljanju. Zdaj jo premakneš za naslovno vrstico, na primer čez ploščo Lastnosti; dvoklik na naslovno vrstico jo vrne pod njen gumb. Žebljiček v naslovni vrstici jo drži odprto, kadar želiš postaviti več oblik zapored. Brez žebljička se po vsaki obliki zapre, kot doslej. Enako velja za oblike v skici.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.86.2) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.86.2) s slovenskim vmesnikom.

v1.86.1

What's new in 1.86.1

• A number on the edge of a body lying on its side changes the right measure
  With a workplane on a face and a body lying on its side (a Round Roof turned by 90°, for example), the number on the vertical edge went into the wrong field: type a new height and another side changed. The number now belongs to the side it stands at, as it already does for a box turned by a quarter.

---

Kaj je novega v 1.86.1

• Številka na robu telesa, ki leži na boku, spremeni pravo mero
  Pri delovni ravnini na ploskvi in telesu, ki leži na boku (na primer Okroglo streho, obrnjeno za 90°), je šla številka na navpičnem robu v napačno polje: vpisal si novo višino in spremenila se je druga stranica. Številka zdaj pripada stranici, ob kateri stoji, kot že pri škatli, obrnjeni za četrtino.

---

Layerling Desktop is a desktop version of the open-source layerling (version 1.86.1) with a Slovenian interface. / Layerling Desktop je namizna različica odprtokodnega programa layerling (različica 1.86.1) s slovenskim vmesnikom.