Skip to content

Releases

v6.3.2

Choose a tag to compare

@github-actions github-actions released this 17 Nov 02:54

What's new in v6.3.2

Fixed puresignal for the 8000 and 7000 series radios

What PureSignal does:
it listens to your own transmitter's output and automatically pre-distorts the signal so the radio transmits cleanly — less splatter, less interference on adjacent frequencies.

What was wrong:
to do that it needs a target level for the feedback signal it measures. Our build used a value of 22 for the ANAN 7000D, 8000D, G2, while every other radio used 152. That 22 came from a development branch, and it doesn't work: the feedback reading was wrong, so calibration never completed properly and the "Correcting" indication never appeared.

What we fixed:
the target is now 152 for every radio, which is the value current main-line Thetis uses (its internal reference is 152.293). No per-radio special cases are left. If you use PureSignal: switch to transmit, run Single Calibrate on each band as usual — this time it should settle and show Correcting, and the feedback level should read in a realistic range.

Added new Digi Id system (still a work in progress)

What it is:
a signal recognizer. It listens to the audio of whatever you're tuned to, measures the signal's characteristics (bandwidth, symbol rate, tone spacing, how often it repeats, modulation type), and compares that against a database of 500+ known digital signals. It then shows the most likely matches, best first, with a confidence score and the reasons for the match.

The database comes from the Artemis database project and includes a waterfall picture and a reference recording for each signal. It is not shipped with the installer — it's a ~288 MB download that the program fetches for you, because otherwise every installer would be that much bigger.

Where it lives: %APPDATA%\OpenHPSDR\SDR-VST3-x64\SigId (the HL2 build uses SDR-VST3-HL2-x64). after the database is installed the program measures every reference recording once to build its "reference data" — a few minutes of work that makes the matching much more accurate. The window tells you it's running and says "Reference data ready (N signals measured)" when it's done.

How to use it:

  1. Open the Digi Id window and click Install Database. Wait for the download (the progress bar and MB/s counter show it) and then the reference-data pass.
  2. Tick Enable identification, pick the receiver (RX1/RX2) and the scope (all signals, Amateur Radio, Hf Digital Modes Example: military digital).
  3. Tune to an unknown signal. The candidate list fills in, best match at the top; click a row to open its details.
  4. If the program says reference data is missing, press Rebuild reference data — it's the only maintenance step you'll ever need, and only after a database update.

Installer

  • .msi — the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v6.3.1

Choose a tag to compare

@github-actions github-actions released this 14 Nov 03:20

Whats new in v6.3.1

many many pure signal 3.0 fixes
Also fixed a bug where you could not adjust custom meters past 15watts with hermes lite connected
Went back to a single .msi installer no more bundled exe installer

PureSignal 3.0 - a short guide for the operator

  1. The Single Cal - measure once, keep the result

A Single Cal is ONE measurement. It runs a test signal, works out your
amplifier's distortion, applies the correction, and stops. The correction
stays applied until you switch PureSignal off.

How:

  1. In the linearity window, pick the stimulus in the "Cal Stimulus" box -
    "Two-Tone" or "Noise".
  2. Press "Single Cal".
  3. It keys up, measures for a second or two, and stops on its own. That's it.
  4. The correction stays applied. To switch PureSignal off, press the "OFF"
    button at the top right of the linearity window. Pressing "Single Cal"
    again does NOT turn it off - it just runs another calibration.

Which stimulus?

  • Noise - "how clean is my actual signal?" The guide by dr. warren pratt is clear that the
    noise test is the honest one, because it is the closest to speech.
  • Two-Tone - repeatable numbers you can compare before and after a change.

One gotcha: if you have not transmitted for a while, the FIRST press can
cancel itself. Just press it again, or start the TX test first (the
"Two-Tone" / "Noise" buttons in the linearity window do that).

In setup test tab:

  • Freq #1 / Freq #2 - the two tone frequencies. Press "Defaults" for
    700/1950 Hz. Do NOT use a spacing that is a neat fraction of 96 kHz 700/1900 the old defaults
    (1200 Hz is exactly 1/80 - the calibration then only sees a few repeated
    levels instead of a continuous sweep, and the correction comes out
    distorted).
  • AmpView - shows the measured gain curve and the correction curve.
  • Save / Restore - store a correction to a file and put it back later.
  • PS Correction (Strict / Medium / Relaxed) - how strict the calibration is
    about the data it is given.
  1. PS-A (auto-calibrate) - keep measuring for ever

PS-A is the button on the console. Tick it and PureSignal re-measures and
re-corrects CONTINUOUSLY, so it keeps up with the amplifier as it warms up, as
the band changes and as the power changes.

  • It needs you to transmit regularly - it can only measure while the
    transmitter is keyed.
  • Leave it on for normal operation.
  • PS-A and Single Cal are mutually exclusive: pressing Single Cal turns PS-A
    off, and PureSignal stays on with the correction it has just made.
  1. The console lights

There are two lights on the info bar at the bottom of the console.

"Feedback" - how hard your amplifier sample is coming back. A number plus a color:

green    just right, you are in the target band
yellow   close, but not quite
blue     TOO MUCH feedback
red      TOO LITTLE feedback

(left-click the info bar if you would rather have red and blue the other way
round)

"Pure Signal" / "Correcting" - dark means PureSignal is off. Green
"Correcting" means the correction is actually being applied.

Two things worth knowing:

  • Both lights only come on while you are TRANSMITTING. No TX, no lights.
  • With PS-A you get both - the feedback number ticks over and the light
    changes colour.
  • With a Single Cal you get ONLY the "Correcting" light. in the linerarity panel A Single Cal is a
    one-off, so a feedback number flashing on the console afterwards would
    only be stale information.
  1. The feedback level and the attenuator

The ATT on TX (the "ATT" setting) is the step attenuator in the transmit
path. It sits in the feedback measurement, so:

Every decibel of extra attenuation = one decibel less feedback reading.

The PureSignal engine has a "target feedback level". The auto-attenuator moves
the ATT on TX until the feedback reading sits on that target. For most radios
the target is 152, it is set in the program and you cannot change it - and you
should not try. A target the rig cannot reach makes the auto-attenuator park
on the end stop of the attenuator (31 dB) with a weak feedback signal, and the
light never goes green.

If you ever see the attenuator stuck at 31 dB with the feedback light yellow,
a wrong target is in use. Tell us, do not try to fix it by hand.

For the record: the feedback numbers under PureSignal 3 are the SAME as under
PureSignal 2 - with the target at 152 the attenuator and the output power land
exactly where they used to.

One caution: the attenuator is in the transmit path, so when it moves, the
drive into your amplifier changes by the same amount. Watch the ALC and the
power when the auto-attenuator walks it.

If you only remember three things

  1. The FB Target is set by the program (152)most radios.
  2. Feedback numbers under PureSignal 3 are the same as under 2. If the
    number and the green light disagree, suspect a wrong target, not a
    broken PureSignal.
  3. A Single Cal needs the TX test running if it cancels itself on the first
    press.

Installer

  • .msi — the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v6.3

Choose a tag to compare

@github-actions github-actions released this 12 Nov 04:14

What's new in v6.3

Fixed

  • Fixed many pure signal 3.0 bugs made the two tone generator more stable
  • See noise button note below

Added

  • Noise button for calibrating pure signal 3.0 to the pure signal panel this is the recommended use case to most closely simulate human speech by Dr. warren pratt the creator of pure signal
  • Frequency Analyzer Gadget

Pure signal work is not complete at this time

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v6.2

Choose a tag to compare

@github-actions github-actions released this 08 Nov 23:08

Whats new in v6.2

Fixed

  • Discord no longer crashes when connecting or receiving messages.
  • Bot no longer gets stuck at ΓÇ£trying to connect.ΓÇ¥
  • ΓÇ£Join Discord ServerΓÇ¥ now actually opens the invite link.

Added

  • DX Cluster terminal window: shows live traffic to/from each cluster node, lets you type commands directly, switch nodes, and save the log.
  • Per-node DX Cluster passwords: each node can save its own password and send it automatically when the cluster asks.
  • Per-node log view and node selector

A few bug fixes
Custom Meter image now saves through restarts.
A few internal bug fixes

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v6.1

Choose a tag to compare

@github-actions github-actions released this 06 Nov 03:31

whats new in v6.1
Bug fixes

  • Courtesy tone fixed: the courtesy tone (and other WDSP playback wavs etc audio) no longer goes through the VST transmit chain when it is active.

  • FreeDV is now added to the gadgets Mode buttons.

  • 3D panadapter: RX1 and RX2 now keep separate display history, so the two receivers no longer interfere with each other's trace.

  • Diversity/Phasing window: no longer grows larger every time it is closed and reopened it now reopens at the size you left it.

  • TCI shutdown crash
    When SDR-VST3 closed, it shut down its TCI connections. Two shutdown routines could try to close the same connection at the same time causing the null-reference crash.

New feature

  • Added the ability to give cross-meter and multimeter analog meter gadgets its own custom face/dial image.

  • Previously, changing the meter face meant changing the default image then a reinstall would overwrite you change. Now you can import the image for that meter.

  • Imported images are copied to a safe app-data folder, so app updates and reinstalls wonΓÇÖt overwrite them.

  • Each meter gadget remembers its own image choice across restarts.

  • Selecting (Default skin) restores the meterΓÇÖs normal skin image.

How to use it

  1. Open Setup → Appearance → Meters/Gadgets.
  2. Select a cross-meter or multimeter meter gadget.
  3. In the Settings box, find Custom skin.
  4. Click Load... and choose a .png, .jpg, .jpeg, or .bmp image.
  5. The image is imported and selected automatically.
  6. To undo it, choose (Default skin) from the dropdown.

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v6.0

Choose a tag to compare

@github-actions github-actions released this 04 Nov 01:36

What's New in v6.0

  • Adjustable PureSignal correction: PureSignal now has a "PS Correction" setting with three options ΓÇö Strict (default), Medium, and Relaxed. Strict corrects the most aggressively; Relaxed is gentler. If your signal looks over-corrected or calibration unstable, try a softer setting.

  • Cleaner PureSignal screen: Removed a set of advanced controls that never actually did anything, so the window is simpler and less confusing.

Pure signal operation

  • The preferred method of using pure single is the single cal mode but it does require recalibration whenever you have a large change in power level or change your select bands etc..

  • The Automatic mode while much more convenient is slow due to the fact that each reset of the attenuator restarts the pure signal control loop then it has to lock on again this is even more of an issue with the new wdsp 2.11 another important factor in this mode is you must have your audio chain gain set to where you regularly touch 0 on the alc meter not the (alc comp meter) as each time it hits 0 it triggers a calibration if it doesn't hit 0 it doesn't calibrate.

  • It does not have to pulse green continuously as once it flashes green its calibrated if your talking and it flashes green its calibrating again but it really does not have to calibrate continuously the whole time you are transmitting if it does great but its not necessary.

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v5.9

Choose a tag to compare

@github-actions github-actions released this 01 Nov 18:05

WhatΓÇÖs new in v5.9

  • Your GPU mesh/compute/overlay settings now stay saved after restarting the program.

  • NR5 is now available in Other Buttons, including its active indicator and meter behavior.

  • DX Cluster login now supports an optional password beside your callsign and sends it automatically when the cluster asks.

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v5.8

Choose a tag to compare

@github-actions github-actions released this 30 Oct 02:36

Whats new

Upgraded to wdsp v2.11 and added an NR5 NNR noise reduction option.

How to use NR5

  1. Turn it on from the main window: click the NR button repeatedly. It cycles: Off → NR1 → NR2 → NR3 → NR4 → NR5 → Off. For the second receiver, use the RX2 NR button the same way. You can also pick NR5 from the main DSP menu.
  2. Adjust it in Setup: open Setup → DSP tab → NR5 tab. There are separate RX1 and RX2 sections with controls for the model, mask floor, maximum gain, smoothing, and timing. Each section has a Defaults button to reset just that receiver.
  3. Remote control: NR5 is also accepted through the existing CAT (ZZNE/ZZNF) and TCI noise-reduction commands.

What each control does

  • Model (0ΓÇô3): chooses which built-in neural network to use. Model 1 is the default larger general-purpose model, model 0 is a smaller general model, and models 2 and 3 are alternative models trained with more context (useful for weaker or CW-style signals). If one model sounds wrong for the noise you have, try another.
  • Mask floor (dB): the lowest gain the noise reducer is allowed to apply. More negative values cut noise harder; values closer to 0 are gentler. Default is -25 dB.
  • Max gain (dB): the most the processor may boost a signal above the noise estimate. Higher values can recover weaker audio but may also amplify artifacts; lower values are safer. Default is 12 dB.
  • Alpha: shapes how aggressively low-level signals below the knee are treated. 1 is neutral, higher values suppress low-level content more, and lower values sound gentler and more natural. Default is 1.
  • Alpha knee (dB): sets where that alpha shaping begins. A higher value applies it only to very low signals; a lower value spreads it over a wider range. Default is 10 dB.
  • Tau (s): how quickly the noise estimate adapts. Longer values track steady noise more smoothly; shorter values follow changing noise faster. Default is 2 s.
  • Smooth attack (ms): how fast the noise reduction opens up when a signal appears. 0 is instant; higher values are smoother but slower. Default is 0.
  • Smooth release (ms): how fast it closes back down after a signal stops. 0 is instant; higher values reduce pumping but leave a longer tail. Default is 0.
  • Output audio in both I and Q: Unchecked by default. Unchecked keeps normal audio in I with Q set to zero, Checked puts audio in both I and Q and is mainly for special routing/testing.
  • Defaults: resets all NR5 controls for that receiver back to the values above.

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v5.7

Choose a tag to compare

@github-actions github-actions released this 17 Oct 16:30

Added DX Cluster and panadapter spotting

The DX Cluster is a pop-up form that shows ham radio stations people are hearing, feeding from internet "telnet" servers.
we also added an SWL Mode (SWL = Shortwave Listening.

Flip it on and the list stops showing ham spots and instead shows shortwave broadcast stations that are on the air right now.
The station data comes free from a public schedule (EiBi) that lists who's broadcasting, on what frequency, at what times, in what language. The app downloads it, works out which stations are live this minute, and lists them.
Each row shows a country flag, the country name, and a new Language column.
While SWL Mode is on, the clutter that only makes sense for ham spotting gets hidden.
It doesn't disconnect anything ΓÇö your cluster connections stay alive in the background, just hidden, so flipping back is instant.
The SWL Mode and Spots on Panadapter buttons light up green when switched on, so you can tell at a glance.

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.

v5.6

Choose a tag to compare

@github-actions github-actions released this 17 Sep 00:43

Whats new bug fixes

  1. Fixed garbled digital transmit audio ΓÇö When you transmit FT8 or fldigi through the radio, the console was routing that signal through all your microphone audio effects (EQ, compression, etc.), which mangled it into multiple chirps / messy spikes. Now the console auto-skips those effects whenever a digital modem is keyed up, so your digital signal goes out clean. Works for both WSJT-X (FT8) and fldigi.

  2. RADE (FreeDV RADE encoder) already behaved the same way ΓÇö verified, no change needed.

  3. cmASIO driver fix ΓÇö Was not listing all asio devices when enabled.

Installer

  • .msi - the SDR-VST3 product. It requires the .NET 10 Desktop
    Runtime
    (x64) to be installed on the machine. The installer checks
    for it and tells you where to get it if it is missing:
    https://dotnet.microsoft.com/download/dotnet/10.0

    If you already have an older SDR-VST3 installed, installing over it
    upgrades in place.