Skip to content

HeaterMeter 4.0 Assembly

uipko edited this page Apr 30, 2013 · 33 revisions

Tools

Parts

HeaterMeter v4.0 PCB

This can be obtained either by finding someone who has an extra (they're usually ordered in 3s and you probably only need one) or by ordering your own set. To order your own set, use any online PCB fab service which supports gerber files. OSH Park is the preferred online service for the U.S., due to their quick turnaround, impeccable output, friendly service, and reasonable prices. Just upload the "dorkbot" zip file to their service and pay them. You'll have boards in your hands in about two weeks. PCB 4.0 Snapshot

OSH Park also now has PCB 4.0 board singles available in their store. OSH Park PCB 4.0 Singles

Hardware Assembly

The HeaterMeter v4.0 PCB has two sides and components go on both sides. The silkscreen outlines indicate on which side components should be placed, but in general most of the components go on the underside of the board. The easiest way to assemble the board is to start with the flattest components and work your way to the larger pieces.

Bottom Components

All directions in this section refer to the board being bottom side up. That is, the side that does not say "HeaterMeter 4.0" on it. The "SP1 Alarm" marking should be furthest from you and the Pit/Food1/Food2/Food3 markings should be on the left.

Cut a piece off one one of your component leads and bend it to fit into the position marked "R7 0" and solder it into place. This is a "0 ohm resistor" needed for the LCD backlight. If you did not use the recommended New Haven Display LCD, you'd instead place the proper current-limiting resistor needed for your backlight here. The New Haven model is nice in that the current-limiting resistor is integrated into the display itself.

Image

Solder the rest of the resistors. The orientation on these does not matter either side can go in either hole, as long as the body of the resistor is on the right side of the board. The placements are sized such that you should be able to fold the leads of the resistor against the body at a right angle and have them just fit into the holes. It is easiest to insert a couple resistors at a time and flip the whole board over, resting the board on the resistors to hold them in place while you solder them and clip the extra leads off. When you're done soldering all the resistors, it should look like this.

Image

Ceramic capacitors (small yellow blobs) Again, the orientation does not matter as these have no polarity.

Image

The diodes have a white line on them to indicate their polarity and should be installed so their white line matches the white line marking on the PCB. Then, solder the DIP-28 socket (IC2) and the DIP-16 74HC595 (IC3). Both of these parts have a notch on one side of them which indicates the direction they need to be placed. Do not install the ATmega328P chip into socket IC2 at this time. Q1 (the fan driver MOSFET) should also be placed. To form its leads, just insert it into the holes and bend it down into position so it stays inside the component outline and the holes match up then flip the board and solder it into place.

Image

Install the RaspberryPi GPIO header, piezo buzzer, and Q2 (LCD backlight driver). Q2 should be mounted so that the flat edge of the component matches the flat printing on the PCB.

Image

Install the electrolytic capacitors (the "cans"). The capacitor is marked with a white line on its negative side and the PCB is marked with a teeny plus sign on the positive side. You want the white line on the capacitor to be opposite the hole marked with a plus sign on the PCB. If that's too confusing, the white line on all the capacitors should be closest to you when installed. Also install the 16MHz resonator (the larger yellow blob) in the unlabeled oval closest to you by the DIP socket.

Image

Install the 5V regulator board, power barrel jack, and blower RCA jack in that order.

Image

We're now done with the bottom components aside from the probe jacks. Note that IC4 (3.3V regulator) is left unpopulated. If you're building a standalone HeaterMeter, populate that with the MCP1700-33 or else nothing will power up. If you're building this to interface with a Raspberry Pi, IC4 is not required. At this point the TOP of the board should look like this, no components on it yet.

Image

Finally, install as many probe jacks as you'll have probes connected.

Top Components

Install R6 (LCD contrast adjustment potentiometer).

Snap off 16 pins from the 36 pin header strip and install them in J1. If you're going to connect the LCD with a ribbon cable of some sort, I'd recommend the short ends be installed into the PCB and leave the long ends sticking up. If you're going to mount the LCD directly, I'd recommend the opposite-- with the long ends through the PCB and the short ends left sticking up.

You might want to pause here. Everything on the top of the board beyond this point needs to be installed at the height appropriate for whatever enclosure you're going to put this in. The LEDs, LCD and buttons will be easier to get their height right if you're soldering them in place while trial-fitting the system into a case.

At this point you can install your LEDs (LED1, LED2, LED3) but bear in mind that if you mount them flush with the board, they will be lower than the button and LCD face. You can either mount them with long leads, or mount them and bend them over to the left so they'd be exposed out the side of the case rather than on the front panel. The longer lead on the LED (the +/anode) is inserted into the hole closest to you. There's a little + sign to indicate this on LED1 but not the others, as that would get confusing with them all so close together.

Finally install the button into the large square position in the center of the board. This should only fit in one orientation, but I'm sure if you try really hard you can force it in the wrong way. Don't try that hard.

Image

To get my button height right, I straightened the pins on it and slid a 3mm spacer under the button before soldering it from the front. Do not insert the leads all the way through the PCB holes or the button will be roughly flush with the LCD when installed in a case. You want the button to be more raised.

[Image] (https://picasaweb.google.com/lh/photo/Fq_F6HWaZ2c4Unt7K6Yh19MTjNZETYmyPJy0liipFm0?feat=embedwebsite)

The LCD can now be installed by soldering all 16 pins in place on the lower of the two connectors on the LCD itself. The LCD extends away from you and hangs off the board.

Do not populate J2 (PROBE), J4 (BLW), J6 (ICSP), or J8 (FTDI) unless you need them. These are provided for users who don't use the integrated connectors.

At this point you can install the ATmega328P into the DIP-28 socket IC2.

Image Image Image

Optional Components

Ambient Temperature Thermistor A thermistor can be attached to one of the probe jacks to allow for ambient temperature measurement when a probe is not inserted into the jack. When looking at the board from the top, solder the thermistor between the far right pin and the close pin of the jack. Remember, the probe coefficients in the configuration need to be set for the proper probe type connected. That is, when you have no probe inserted the configuration should be set for the thermistor coefficients and when a probe is inserted they should be set to match the probe type. This modification can be seen on the Food3 jack here

Image

Wireless Probe Support HeaterMeter supports receiving ambient temperature from LaCrosse Technology IT+915 protocol weather stations as well as custom-built "lmremote" probe transmitters. If this is desired, install a RFM12B transceiver board. A short piece (78mm) of insulated solid-core wire should be installed into the hole marked ANT as an antenna.

Software Installation

See: HeaterMeter 4.0 Software

Clone this wiki locally