-
Notifications
You must be signed in to change notification settings - Fork 83
HeaterMeter 4.0 Hardware
As a reminder, HeaterMeter refers to the ATmega (Arduino) based microcontroller board that runs the LCD, reads button and temperature probe inputs, and controls the blower motor. This document describes the configurations and design of the HeaterMeter board, which may optionally be attached to a Raspberry Pi. For connecting directly to a Linksys router, use HeaterMeter 3.0 Hardware.
Standard HeaterMeter hardware is built on a HeaterMeter v4.0 PCB
- Buy direct from OSH Park
- Schematic Image
- EAGLE 5 schematic and board
- DorkBot/OSH Park cam job or cam output. Use cam output if you just want a board made with no modifications
HeaterMeter can be built either as a standalone or for integration with a Raspberry Pi. The only difference between the two is the population of the Pi socket JP1. The 3.3V voltage regulator is not required when connecting to the Pi, but it is when operating standalone. Both configurations provide automatic grill control, and LCD display. Set Point, manual fan mode, probe offsets, open lid detect and max fan speed configurable via buttons. The standalone requires initial configuration via serial commands. There is integrated no web access or graphs in standalone mode, but there is a serial status output to allow you to roll your own solution.
Qty | Value | Device | Parts | Link |
---|---|---|---|---|
1 | 0 | R-US_0204/7 | R7 | (wire) |
4 | 390 | R-US_0204/7 | R2, R10, R12, R15 | Mouser DigiKey |
1 | 680 | R-US_0204/7 | R8 | Mouser DigiKey |
3 | 1k | R-US_0204/7 | R1, R3, R4 | Mouser DigiKey |
2 | 2k2 | R-US_0204/7 | R9, R13 | Mouser DigiKey |
1 | 4k7 | R-US_0204/7 | R11 | Mouser DigiKey |
1 | 10k | R-US_0204/7 | R20 | (use below) |
4 | 10k 1% | R-US_0204/7 | R5, R16, R17, R18 | Mouser DigiKey |
1 | 10k | TRIM_US-CT6 | R6 | Mouser DigiKey |
3 | 0.1u | C-US025-025X050 | C2, C3, C10 | Mouser DigiKey |
1 | 22u/25 | CPOL-USE2.5-6 | C1 | Mouser DigiKey |
2 | 100u/10 | CPOL-USE2.5-6 | C5, C6 | Mouser DigiKey |
1 | 100u/25 | CPOL-USE2.5-6 | C4 | Mouser DigiKey |
1 | OKI-78SR-5 | OKI-78SR-05H | IC1 | Mouser DigiKey |
2 | 1N4001 | DIODE-DO41-7 | D1, D3 | Mouser DigiKey |
1 | ATmega328P | AVR-MEGA8-PPTH | IC2 | Mouser DigiKey |
1 | 74HC595N | 74LS595N | IC3 | Mouser DigiKey |
1 | 16MHz | RESONATORRESONATOR-PTH | Y1 | Mouser DigiKey |
1 | BC337 | BC337 | Q2 | Mouser DigiKey |
1 | FDP7030BL | MOSFET-NTO220HS | Q1 | Mouser DigiKey |
1 | LCD | PINHD-1X16 | J1 | Mouser DigiKey |
1 | TACTILE-4 | TACTILE-4 | S2 | Mouser |
1 | TACTILE-4-CAP | TACTILE-4-CAP | S2-CAP | Mouser Rnd Mouser Sqr |
1 | ALARM | SPEAKER/AL11P | SP1 | Mouser DigiKey |
3 | GRN | LED3MM | LED1, LED2, LED3 | (any ~3mm LED, any colors you want) MouserR MouserY MouserG |
1 | POW | POWER_JACKPTH | J9 | Mouser |
1 | PINHD | PINHD | J1 (LCD), J2 (PROBE), J4 (BLW), J8 (FTDI) | Mouser |
1 | DIP28 | DIP28 | IC2-SOCK | Mouser |
Qty | Description | Link |
---|---|---|
1 | 12VDC/1A power brick 5.5x2.1mm barrel jack | Generic |
1 | Blower-style fan 12VDC 5-10CFM | DigiKey |
1-4 | Maverick BBQ Thermistor Probes for ET-72/ET-73 (3ft or High Heat) | Maverick Amazon |
These are the "built in" connectors, there is space on the PCB for them. External connectors can be used by attaching to the J2 and J4 pin headers.
Qty | Value | Device | Parts | Link |
---|---|---|---|---|
1 | RCAPOWER | RCAPOWER | J5 | Mouser DigiKey |
1 | Pi | PINHD-2X13 | JP1 | DigiKey (alt DigiKey) |
1-4 | Probes | AUDIO-MONO | JP3, JP4, JP5, JP6 | DigiKey |
Qty | Value | Device | Parts | Link | Reason |
---|---|---|---|---|---|
1 | Ambient | THERMISTOR_R-2,5 | TR1 | Mouser | Only if you want an onboard 'ambient' temperature sensor |
1 | RFM12B | RFM12B | U$1 | ModernDevice | Only if building wireless probes |
1 | MCP1700-33 | MCP1700-33 | IC4 | Mouser DigiKey | Only for standalone HeaterMeter |
1 | ICSP | PINHD-2X3 | J6 | Mouser | Only if flashing the AVR outside of the Pi |