Skip to content

Machines and ROMs

WacKEDmaN edited this page Nov 14, 2026 · 3 revisions

Machines and ROMs

The Machine menu and the Machine window choose the computer and its chips. A change of model, RAM or CRTC starts the machine again.

Model

Machine → Model:

Model Command-line id
CPC 464 cpc464
CPC 664 cpc664
CPC 6128 cpc6128
464 Plus cpc464plus
6128 Plus cpc6128plus
GX4000 gx4000

The Plus and the GX4000 start from their system cartridge, or from the Plus ROM files when they are in the ROM folder (refer to Installation and first start).

RAM

Machine → RAM: 64 KB (as sold for the 464 and 664), 128 KB, then 256, 320, 512, 576 KB, and in 512 KB steps up to 4160 KB (64 KB + 4 MB).

  • On a GX4000, the choice is 64 KB (as sold) or 128 KB (the RAM mod). With 128 KB, 128K software runs as on a 6128 Plus.
  • On a Plus, the RAM above 128 KB can be:
    • Expansion: a classic board: a board on the expansion port, as sold for the CPC. It does not know about the ASIC: with its RAM paged in at &4000 and the ASIC page in, a write goes to both.
    • Expansion: an internal upgrade: RAM added inside the Plus. It behaves as the Plus's own RAM (a write under the ASIC page goes to the ASIC only).

Video chips

CRTC

Machine → Video chips → CRTC:

Type Chip
0 HD6845S / UM6845
1 UM6845R (1-A)
2 MC6845
3 ASIC (Plus)
4 Pre-ASIC (the cost-down CPC)
5 UM6845R (1-B, RFD#10)

Each type has its own rules, from the Amstrad CPC CRTC Compendium by Longshot, checked with the SHAKER test suite and photographs of real machines. Demos that use CRTC tricks show the same picture as on a real machine with that chip.

Gate Array

Machine → Video chips → Gate Array (a classic CPC only):

Part Machines
40010 Most 6128s, later 464s and 664s. The reference part.
40007 Early 464s, some 6128s. Its decoder is 1/16 µs ahead at a mode change.
40008 Mostly 664s. The same timing as the 40007.

On a Plus or with CRTC type 3 or 4, the ASIC (40489 or 40226) is the Gate Array: there is no separate part to choose.

Z80

Machine → Z80:

  • NMOS Z80A: the part that every CPC, Plus and GX4000 had. Use this.
  • CMOS Z84C00: a replacement part. OUT (C),0 writes &FF on it, not 0. Most music players use that instruction, so on this part their music goes wrong and the tape motor relay clicks, as on a real CPC with a CMOS Z80.

ROMs

The ROMs window (also Machine → ROMs) shows the firmware of the machine and the expansion ROM slots.

  • Lower ROM (OS), ROM 0 (BASIC) and ROM 7 (disc DOS): Replace takes another ROM file, Default goes back to the ROM of the model. ROM 7 can be AMSDOS, or ParaDOS, ROMDOS and others for more disc formats.
  • Expansion ROM slots 1 to 15 (and more): Fit puts a ROM file in the slot, Clr empties it.
  • A ROM file can be 16 KB, or a file with a 128-byte AMSDOS header (the header is removed).
  • The ROMs that you choose are saved in cpcse.ini and come back at the next start. If a file is gone, the status line says which.
  • On a Plus, an expansion ROM in a slot below 128 answers in place of the cartridge's page for that number (ROMDIS), as a ROM board on the expansion port does.

Some expansions bring their own ROMs (for example the M4 Board, or the SYMBiFACE III SD card ROM banks). Refer to Expansions.

Machine profiles

A machine profile keeps a whole machine in a .cpcmachine file, so you can build it again with one click. Use Machine → Machine profiles.

  • The list shows your saved profiles. Click a profile to load it. The profile in use has a tick.
  • Save this machine as a profile... saves:
    • the model, RAM, CRTC, Gate Array and Z80
    • the keyboard region, the joystick and the monitor set
    • the firmware ROMs that you chose and every expansion ROM slot
    • every expansion with its settings and folders: M4, Multiface II, RS232C, SYMBiFACE II/III, mouse interface, IDE, both Albireo boards, HD20, light gun, GFX9000, OPL4, PlayCity, speech, the MP3 card and the DAC
  • Save this machine with its media... also saves the discs in drives A and B, the tape and the cartridge.
  • Load a profile file... loads a profile from another folder.
  • Open the profiles folder shows the machines folder in your file manager.

When you load a profile:

  • The profile is the whole machine. An expansion that the profile does not name is removed. Then the machine restarts.
  • A folder that the profile does not name stays as it is.
  • A profile without media leaves the discs in the drives.
  • If a ROM or disc file is not found, the status line names it. The rest of the profile loads.

You can also load a profile with File → Open → Machine profile, drop a .cpcmachine file on the window, or start with --machine <name or file> (refer to Command line).

Folders. A profile can name the folders of the M4, IDE, Albireo and SYMBiFACE III cards and the HD20 image. A program on the CPC can write to those folders, and change or delete the files in them. When a profile names folders that are not yours, a window shows them and asks:

  • Keep my folders: the profile loads, and your folders stay.
  • Use the profile's folders: use this only for a profile that you know.
  • Cancel: the profile does not load.

On the command line, --machine keeps your folders. Add --machine-folders to use the folders of the profile.

A profile is a text file with the same key=value lines as cpcse.ini. You can write or change one in a text editor. For example:

# CPCSyntaxError machine profile
name=SymbOS 6128
model=cpc6128
ram=576
symbiface=sf3
m4=1
m4folder=F:\CPC\M4
xrom_6=F:\CPC\roms\symbos.rom

Reset, pause and speed

  • Machine → Reset (Ctrl+R) and the Reset machine button in the Machine window: power off and on.
  • Machine → Pause (Ctrl+P).
  • Machine → Speed: 25%, 50%, 100%, 200%, 400%. Unlimited speed runs as fast as your computer can.

Movies

Machine → Movie records and plays input movies. Refer to Snapshots, save slots and the timeline.

Clone this wiki locally