Skip to content

Video and Monitor

WacKEDmaN edited this page Oct 31, 2026 · 1 revision

Video and monitor

All these settings are in the Video menu and in Window → Settings → Video settings.

The monitor set

Video → Monitor chooses the monitor that the CPC is connected to. As shipped with the machine uses the set that came with the model.

Set Tube
CTM 644 (colour) Colour, slot mask. The default.
CTM 640 (colour) Colour
CM14 (464+/6128+ colour) Colour
GT 65 (green) Green phosphor
GT 64 (green) Green phosphor
MM12 (paper white) White phosphor

The monitor locks to the composite sync that the Gate Array makes, as a real monitor does. Demos that change the sync show the bends, rolls and shifts that a real monitor shows.

The knobs

  • H. Hold: the horizontal oscillator. 0 is the set as the service manual aligns it. Turned too far, the set can no longer hold the line and the picture breaks into diagonal bars.
  • V. Hold: the vertical oscillator. Turned too far, it no longer holds the CPC's 312 lines and the picture rolls.
  • Centre both puts both holds back to 0.
  • Brightness: the knob on the front of the set. 50 is the set as calibrated. Turn it up and dark colours light up.
  • Contrast: the second knob of the monochrome sets (GT 64, GT 65, MM12). 100 is full.
  • Reset knobs puts the knobs back.
  • Output colour: the red, green and blue output of the set plugged in now, 0 to 200%.

The tube

Video → Tube: As set (the tube of the monitor set), Colour, Green, Grey or Mono. For example, choose Green to see a colour game as on a GT 65.

The renderer

  • Standard: makes each line from what the Gate Array captured on that line. Use this.
  • Beam (pin-accurate CRT): draws each Gate Array character at the place of the live beam, from HSYNC and VSYNC. For classic machines only (a Plus keeps the standard renderer).

Which screen

With a GFX9000 fitted, the CPC screen and the GFX9000 screen each have their own scaling, CRT effect and Advanced CRT Filter. Video → Screen chooses the screen that the settings below are for: CPC screen or GFX9000 screen. Copy the CPC screen's settings copies all of them to the GFX9000 screen. Until you change them, the GFX9000 screen uses the CPC screen's settings.

Scaling

  • Integer scaling: each CPC pixel is a whole number of screen pixels. For the GFX9000 screen, each row is a whole number of screen pixels, and the width follows the shape of the monitor.
  • Maintain aspect ratio: the picture keeps its shape. Off: it fills the window.
  • Fullscreen (F11), and Full screen: the picture only (full screen with no menus or windows).

The CRT effect

Video → CRT effect draws the tube's own pattern over the picture. It costs little.

  • Pattern:
    • As the set: a colour set has a slot mask; a green or grey set shows scanlines.
    • Slot mask: the phosphor stripes and slots of a colour tube. Each red, green or blue slot lights as a whole.
    • Soft slot mask: fine dark lines over the picture; each pixel keeps its colour whole.
    • Scanlines: dark lines between the CPC's lines.
    • None.
  • Slot mask strength and stripe width (the width of one phosphor stripe on your screen, in pixels; a triad is three stripes).
  • Turn the mask 90 degrees: stripes across the screen and slots in rows.
  • Scanlines: their darkness.
  • Bloom: a glow round bright pixels.
  • Blur: the round, soft spot of the beam softens the pixel edges. 0 is sharp.

The Advanced CRT Filter

Video → Advanced CRT Filter draws the picture on the graphics card in two stages. Each stage can be off. While the filter is on, the CRT effect is not drawn.

Signal: PAL colour and scanlines: the picture as a PAL signal.

Setting What it does
Blur Spreads the brightness to the pixels on each side
Scanline shade The brightness of the line between two scanlines
Saturation, Contrast, Brightness, Gamma As on a TV
Tint Turns the colours towards red
PAL odd line phase, PAL odd line offset The colour error of alternate lines, as a PAL decoder has

Screen: glass, mask and glow: the tube's glass.

Setting What it does
Pattern scale The size of the mask and lines, in screen pixels
Scan lines: every n lines, Lines darkened, Darkness (%) Dark lines every few screen lines; lines in rows or in columns
Bulge (%) The curve of the glass
Rounded corners (%), Corner dot Dark rounded corners, with a lit dot in each
Bleed (%), Glow (%) Light into the pixels round each pixel, and further for bright ones
Mask (%), mask shape, Stripe width A phosphor mask: stripes, stripes with gaps, slots or dots
Tint colour, Tint (%) A colour over the picture
Roll per frame, Rolling bar (%) Dark lines that move, and a bright bar that rolls down

Defaults puts back the default values.

The GFX9000 monitor

Video → GFX9000 monitor (when a GFX9000 is fitted): Beside the CPC screen, Own window, One monitor (switched) or One monitor via a Video9000. Refer to GFX9000.

Raster timing overlay

Debug → Raster timing overlay puts a tick on the picture at each place where the program wrote to the CRTC, the Gate Array, the PPI or the Plus palette, as the beam swept it. A key in the top right corner gives the colours. Refer to Debugger.

Clone this wiki locally