Skip to content

Printing

NebulaOS edited this page Nov 6, 2026 · 6 revisions

6. Your first print

What this step does

Loads filament, prints a small test, and tunes the first layer while you watch it. Pick something small and simple: a 20 mm calibration cube tells you more in 20 minutes than a six-hour model tells you in six hours.

What you need

Before you begin

The nozzle reaches 200 °C and above while loading and printing. It does not look hot. Do not touch the nozzle or the metal around it.

Learn the difference between Cancel and Stop before you need it. They sit next to each other on the print screen and they are not alternatives:

Button What it does When to use it
Pause Parks the toolhead and holds temperatures. Resume carries on. A filament change, or a look at something
Cancel Ends the print tidily. Asks you to confirm. You have changed your mind
Stop Emergency stop. Cuts all movement and all heaters instantly. Something is going physically wrong

Stop needs a power-cycle or a firmware restart afterwards before the printer does anything again. Its label is only "Stop", so it is easy to press expecting a gentler Cancel. Use Cancel unless something is actually wrong.

Load filament

Home → Extrude opens the filament panel.

The filament panel

  1. Cut the filament end at a clean angle. A squashed or stringy end jams.
  2. Feed it into the extruder inlet until it will not go further easily. Do this before you tap Load - Load expects the filament to be in the throat already.
  3. Choose the hotend target for your filament - 200 °C suits most PLA, 240 °C most PETG. The selector offers 180 to 300 °C in steps of 20; for an exact value, tap the temperature on the Home tab instead.
  4. Tap Load. The nozzle heats, then filament feeds forward. If Spoolman is set up, it asks "Use this filament?" first.
  5. When the plastic coming out runs clean and consistent in your new colour, tap Cooldown. During Load, Cooldown is the stop control - the only button that stays active.

Unloading: choose the target for the filament that is loaded, tap Unload, and when it stops, pull the filament out from the top of the extruder by hand. The printer pulls it clear of the hot end but does not eject the whole length.

Changing colour: unload, then load. A print that asks for a colour change (M600) shows this box and walks you through the same steps:

M600's filament-change box

The real screen app, showing the text of NebulaOS's M600 macro (the title scrolls).

Every other control on the filament panel: Home and printing.

Get the file onto the printer

Three ways, all equivalent:

  • From the slicer - upload straight to the printer (5. Set up your slicer).
  • Mainsail - drag the file into the file list in your browser.
  • USB stick - plug it in; the printer's file browser reads it directly.

Start the print

  1. On the Home tab, tap Print. The file browser opens.
  2. Find your file. Files on a USB stick appear alongside the ones stored on the printer.
  3. Tap it, then Print.

The file browser

The print status screen appears by itself. Before the first layer, the screen shows the start steps: preparing, heating the bed, the bed mesh of the print area, heating the nozzle, the purge line next to the print. Then the first layer begins.

The print status screen during a print

Every readout on this screen: Home and printing.

Watch the first layer, and fix it live

This is the most useful thing on the screen, and it is meant to be used.

Tap the Z-offset readout on the print screen (or Tune → Z Offset) to get step buttons: ±0.001, ±0.005, ±0.01, ±0.025 and ±0.05 mm. Watch the first layer and nudge:

What you see What to do
Lines not fusing, gaps between them Nozzle too high - press −
Lines translucent or completely flat Nozzle too low - press +
Lines squished together and fused, no gaps Correct - leave it

Move in small steps and give the printer a few seconds to show the result. Every tap is saved immediately and used for the next print too.

The Z offset screen

Fine Tune (a button on the print screen, also Tune → Fine Tune) adjusts speed, flow and pressure advance live. Speed and flow there are percentages of what the file asked for.

The Fine Tune panel during a print

Still not right after a few nudges? Improve your prints starts from what you see.

When the print finishes

The printer stops heating and parks, and the status screen shows the print as complete. Let the bed cool before removing the part - parts release far more easily cool.

If you were recording a timelapse, the video is rendered now and appears in Mainsail. Settings → Printer → Statistics shows your recent prints and the totals for the printer's whole life (Statistics).

If filament runs out

With a filament sensor, the print pauses when filament runs out instead of printing nothing. The screen offers Load, Continue or Cancel: load the new filament, then Continue.

The filament runout dialog

The screen's own runout dialog. Details: Home and printing.

Spoolman (optional)

If you run a Spoolman server, NebulaOS can track what is left on each spool: set the server under Settings → Connections → Spoolman, then Home → Extrude → Spoolman shows the spool list, and loading asks which spool you are using. Everything else works without it. Details: Settings → Connections and Home and printing.

Troubleshooting

What happens What to do
Filament will not feed Cut a fresh clean end, and make sure it is in the throat before tapping Load.
Nothing comes out, motor clicking Nozzle not hot enough, or a blockage. Raise the target and try again.
The old colour keeps coming Normal - keep going until it runs clean, then Cooldown.
The print will not start Check the printer is not already busy, and that the file sliced correctly.
No mesh or purge line before the print The slicer's start G-code does not call START_PRINT - 5. Set up your slicer.
First layer is poor Adjust Z offset live, as above. One side consistently worse: Axis Twist.
The print stops partway Check for filament runout. After a power cut, see Power-loss recovery.
You pressed Stop Power-cycle the printer, or run FIRMWARE_RESTART from the console.
The part will not come off Let the bed cool completely first.

Next step

7. Keeping NebulaOS updated.

Need help? Troubleshooting · Every button: Home and printing

Clone this wiki locally