Repository navigation
FT8 and FT4
The FT8/FT4 tab: receiving and transmitting FT8 (15 s cycle) and FT4 (7.5 s cycle) over USB audio – WSJT-X-style waterfall and station lists, automatic QSO sequence and logging.
- Turn monitoring on (radio audio over USB). The decoder gets the audio before the monitoring filters – NB, ANF, AI or “DX voice” in the headphones do not affect decoding.
- The band buttons (160m…6m) set the standard frequency and DATA-U mode. Radio filter: at least 3000 Hz.
- The Mac clock must match UTC (FT8 tolerates about ±1 s, FT4 less). The program checks the clock over NTP (time.apple.com) at start-up and with Check clock. When most stations show DT beyond ±0.5 s, a warning appears. In System Settings → General → Date & Time turn on Set time automatically.
- While the FT8/FT4 tab is open, the waterfall takes the place of the RF scope (about 72 s, almost 5 cycles) – the station lists get the whole tab panel. The scope returns when you switch to another tab.
- Newest line at the top; the grey line with a UTC time marks the start of a cycle. Scale 0–3200 Hz.
- Left button – receive frequency (green marker), right button or Shift+click – transmit frequency (red, dashed; on the scale the TX bracket sits above the RX bracket). Markers can be dragged. In the TRANSMIT panel: the TX field with 10 Hz steps, plus TX = RX and RX = TX. A change during transmission applies from the next period.
- Where to transmit: when calling CQ pick a clear spot in the waterfall (no signals for a few periods); when answering a CQ you can transmit on the station's frequency (default – double-click moves TX there) or off to the side (Hold TX).
- The waterfall brightness (☼) and contrast (◑) sliders – in the top row, next to the band buttons (together with TX level).
- Band activity – all messages of each cycle (UTC, dB, DT, Hz, message, country). RX frequency – messages near the green marker and all messages addressed to you.
- Colours – see Colours in the station lists below. Hovering over a message lists the matching categories and the country (e.g. “New DXCC · CQ in message · Malawi”).
The colours and categories are the same as WSJT-X “Decode Highlighting” (same colours, same order). The Colours… button above the list opens the category list with checkboxes: a row's colour is set by the first ticked category from the top that matches the message. Text on a coloured background is black. Ticked by default: my call, new DXCC, unconfirmed DXCC, new DXCC on band, unconfirmed DXCC on band, CQ, transmitted message – enable the others as you need (Default / All).
- 🟥 My call in message – someone is calling you (a reply to your CQ, a report, RR73, 73). These always also appear in the RX frequency window.
- New continent / on band – a continent not in your log (or not on this band).
- New CQ zone / on band, New ITU zone / on band – the same for zones (for WAZ and similar awards).
- 🟪 New DXCC (magenta) – the country is not in your log on any band; on band (light pink) – the country is there, but not on this band.
- Unconfirmed DXCC (purple) – the country is in your log, but no QSO with it is confirmed; on band (light purple) – worked on this band but not confirmed there (confirmed on another band). Confirmation: LoTW, plus eQSL and QRZ if “also count…” is ticked in the confirmations window; changing these switches recalculates the colours immediately. Listed above “New DXCC on band”, because an unconfirmed entity matters more for DXCC than a new band.
- 🟧 New grid / on band – a 4-character locator from the CQ (e.g. JO31) you do not have (for VUCC and grid awards).
- 🟦 New call (cyan) – no QSO with this station yet; on band (light cyan) – worked, but not on this band.
- 🟩 CQ in message – a normal CQ from a station you have not worked on this band yet, when none of the ticked categories above match.
- Grey text, no background – a station already worked on this band (in any mode): its CQ is neither green nor purple – even when its entity is not confirmed yet, because another QSO with the same station usually changes nothing (the confirmation comes when that station uploads its log); purple stays for other stations from that entity. Here the program differs from WSJT-X and works like JTDX. Its messages in QSOs with others are grey too. The same rule applies to “unconfirmed DXCC” alerts and to calls on the scope.
- 🟨 Transmitted message – your own message (in the period you transmitted).
- No colour – QSOs between other stations (not a CQ and not to you), free text, calls hidden in a
<…>hash.
How it is determined:
- “New …” categories apply to CQ messages only – as in WSJT-X. In each pair at most one matches: “new” (not in the log at all) or “new on band”.
- Country, continent, zones – from the cty.dat database (including portable calls, e.g. DL/SP5XTF, SP5XTF/MM); for logged QSOs – from the CONT, CQZ, ITUZ fields, falling back to cty.dat. Without the database (CONTEST tab → Update country database) the “Country” column is empty and the country, continent and zone categories do not appear.
- Call – the base call: SP5XTF and SP5XTF/P are the same station. Grid – only when it is in the message (a CQ with a locator).
- Everything in any mode; band – the band the radio is on (dial from CAT); without CAT only the general categories work.
- The logbook is checked live: after a QSO is logged the colours of the whole list are recalculated immediately – rows of that station already on screen turn grey, without waiting for the next period.
- Hovering over a message lists all matching categories (including unticked ones) and the country.
- Only CQ and to me (above the list) hides messages from other QSOs – CQs, calls to you and your own messages remain.
- The WSJT-X categories “New US State” and “LoTW User” are not available – the program does not have this data.
- Clicking a message sets the receive frequency to that station and puts its call into the log entry field. Double-click – call that station (see below). Transmitted messages have a yellow background.
- Requires Enable TX, the radio in DATA-U and the “To radio (TX)” device in the AUDIO tab. Set TX level (top row, next to the band buttons, together with the waterfall brightness and contrast) so that ALC barely moves; FT8 is a continuous carrier for 12.6 s – 20–50 W is usually enough.
- Messages Tx1–Tx6 as in WSJT-X: Tx1 – call and locator, Tx2 – report, Tx3 – R+report, Tx4 – RR73, Tx5 – 73, Tx6 – CQ. The dot marks the message sent in the next period (click another to change). ✓ – the encoder confirmed the message; ⚠ – the receiver would see something else (the tooltip shows what) and such a message will not be sent. Messages can be edited; Generate restores the standard ones.
- Calling a station: double-click its CQ – the program fills in the call, locator and report (the SNR you hear it with), picks the opposite period and starts TX. Skip Tx1 – starts with the report (Tx2) instead of the locator; the QSO is one period shorter and the locator from the CQ still goes into the log. CQ – call CQ (Tx6).
- Auto sequence: after each period the program picks the next message: locator → report (Tx2), report → R+report (Tx3), R+report → RR73 (Tx4), RRR/RR73 → 73 (Tx5). When several stations answer your CQ at once, the choice is set in Several callers: strongest (highest SNR), weakest, farthest or nearest. Distance is measured from your locator: from the locator in the station's message, from the locator it sent earlier (CQ, Tx1) in this session, or otherwise from the country's position (cty.dat). With equal or unknown distance the higher SNR wins. During a QSO other callers are skipped (they show in red). The sequence options are under the Options… button in the transmit panel (a summary of the current settings below it). Call limit (3, 5, 9 or no limit; 5 by default): the program calls a station that does not answer this many times in a row (call and R-report), then stops transmitting with the message “… did not answer after N calls”; each answer from that station starts the count again, CQ has no limit (the watchdog takes care of it – 6 min). After a QSO, answer the next caller (on by default): after a QSO started from your CQ, transmitting does not stop – in the next period the program answers the next calling station (per “Several callers”), and if nobody calls it returns to CQ; a “73” from the station of the QSO just logged does not get in the way. After a QSO from your own call (S&P), “Disable TX after 73” applies.
- Logbook: after RR73 or 73 is sent the QSO is logged (once per station): FT8, or MFSK/FT4; frequency = dial + transmit tone; reports, locator, country, zones, distance. Then TX turns off (Disable TX after 73) – if the station missed your RR73 and repeats the report, click Start TX and RR73 goes out again (without a second log entry).
- Period: 1st = :00 and :30, 2nd = :15 and :45 (FT4: every 7.5 s). PTT is keyed at the start of the period and audio starts 0.5 s later – as in WSJT-X (DT = 0). Starting TX up to 2 s into a period still transmits in it (with the beginning cut).
- Hold TX – double-click does not move the transmit frequency (split, Shift+click the waterfall). Without it you transmit on the called station's frequency.
- Safety: Halt stops immediately; turning Start TX off lets the current message finish. Withdrawing “Enable TX”, disconnecting the radio, changing band or mode – immediate stop. The watchdog turns TX off after 6 min without your action (every click or QSO progress restarts it). The radio's transmit time limit also applies.
- The PSKReporter switch (below the waterfall, on by default) reports received stations to pskreporter.info – so transmitting stations can see on the map where they are heard. This is what “Enable PSK Reporter Spotting” does in WSJT-X; if WSJT-X runs in parallel on the same audio, enable reporting in only one program.
- Following the service rules: a packet at most every 5 minutes (with a random offset), each station at most once per hour per band and mode, a single UDP socket, frequency = dial + tone. Only calls decoded directly are reported – not those expanded from a
<…>hash, nor your own messages. - Requires your call and locator in the station profile and a radio connection (frequency). The antenna field – an optional antenna description. The number next to it is stations reported since start-up; the tooltip shows the time of the last upload.
- The ft8_lib library (Kārlis Goba YL3JG, MIT) with added subtraction of decoded signals (Depth: Fast = 1 pass, Normal = 2, Deep = 3) and WSJT-X-style SNR.
- Measured: on band recordings about 75 % of the messages WSJT-X decodes (plus a few percent WSJT-X did not report). Threshold: FT8 – reliable down to −17 dB, half at −18.7 dB (WSJT-X about −21 dB); FT4 – down to −13 dB, half at −14.5 dB. The weakest stations are missed more often than in WSJT-X.
- SNR matches the true value within ±1 dB (measured on signals in white noise); DT matches WSJT-X.
- Live comparison: WSJT-X can run in parallel on the same audio input (without CAT – or through CAT Share).
- Switching FT8 ↔ FT4 retunes the radio to the new mode's frequency on the same band (e.g. 40 m: 7.074 ↔ 7.0475 MHz). When the new mode has no frequency on the band (FT4 on 160 and 60 m), the frequency stays unchanged.
- The km column in both lists: distance from your locator – from the station's locator (from the message or its earlier messages in this session); “~” – no locator, approximated from the middle of the country (cty.dat). The “Rx frequency” window is wider – it fits the whole message with the distance.
- QRZ/HamQTH data in the log: once a station is chosen (double-click, answering a CQ, the next caller, Hound), the program fetches its data in the background, so the QSO is logged with name, QTH and the rest (empty fields only; the locator from the FT8 message stays; a station away from home – name only). If the data does not arrive in time, the QSO is completed right after logging.
- When a DXpedition announces Fox/Hound (usually on its own, unusual frequency), tick Hound in the transmit panel. TX moves above 1000 Hz (the Fox does not answer callers lower down), transmitting in the 2nd period (the 1st belongs to the Fox). The summary under the buttons turns orange.
- Double-click a Fox message (e.g. its CQ) – calling with Tx1 (Fox call, your call, locator). The TX frequency does not change; “Skip Tx1” does not apply in Hound mode. Calling without a call limit (the watchdog keeps watch).
- When the Fox answers with a report, the program itself sends Tx3 “R+report” on the Fox's frequency (repeats 300 Hz higher) – “Enable TX” is required. After RR73 from the Fox the QSO goes to the log, transmitting stops (a Hound does not send 73) and TX returns to the calling frequency. Without RR73 after 5 × R+report transmitting stops – check the QSO in the DXpedition's online log.
- The program also decodes the Fox's combined messages (“K1ABC RR73; SP5XTF <KH1/KH7Z> -12” – RR73 for one station and a report for another); a message to you is highlighted. SuperFox mode (signed protocol) is not supported.
- Do not call ordinary stations in Hound mode – untick Hound after working the DXpedition.
Generated from the built-in help of FT-710 Control 0.9.5-beta – do not edit here; changes go into the program (Help.swift) and tools/make_wiki.py. · Wygenerowane z pomocy programu – nie edytuj tutaj.
English
- Getting started
- Station profile
- VFO and tuning
- Filter, AGC and noise reduction
- Transmitting and safety
- RF scope and waterfall
- Display – colours and 3D mode
- Logbook, QRZ.com and map
- Online services (LoTW, QRZ, eQSL, WRL…)
- DX Cluster
- SSTV – images
- CW – decoder and sending
- Propagation
- RTTY – decoder and sending
- FT8 and FT4
- PSK31 and PSK63
- Tools: SWR sweep and who hears me
- POTA – Parks on the Air
- Alerts
- Contests – scoring and Cabrillo
- CAT Share (WSJT-X, JTDX)
- USB audio
- Remote operation
- Diagnostics
- Shortcuts
- Troubleshooting
- About
Po polsku
- Pierwsze kroki
- Profil stacji
- VFO i strojenie
- Filtr, AGC i redukcja szumów
- Nadawanie i bezpieczeństwo
- Skop RF i waterfall
- Ekran – kolory i tryb 3D
- Dziennik, QRZ.com i mapa
- Usługi online (LoTW, QRZ, eQSL, WRL…)
- DX Cluster
- SSTV – obrazy
- CW – dekoder i nadawanie
- Propagacja
- RTTY – dekoder i nadawanie
- FT8 i FT4
- PSK31 i PSK63
- Narzędzia: pomiar SWR i kto mnie słyszy
- POTA – Parki w eterze
- Alerty
- Zawody – punktacja i Cabrillo
- CAT Share (WSJT-X, JTDX)
- Audio USB
- Praca zdalna
- Diagnostyka
- Skróty
- Rozwiązywanie problemów
- O programie