Repository navigation
VFO and tuning
SP5XTF edited this page Nov 3, 2026
·
1 revision
- Mouse wheel over a digit changes that digit (over the hundreds of hertz – by 100 Hz, over kHz – by 1 kHz, etc.). Wheel up always increases the frequency.
- Click a digit to select it: ↑ / ↓ change it, ← / → move to the neighbouring digit, Esc ends.
-
Field next to the mode – type a frequency and press Enter:
7.074(MHz),7074or7074.5(kHz),7074000or7.074.000(Hz); a unit may be added, e.g.21.074MHz.
- VFO-A: mode, RX BW (filter width), TX BW (SSB transmit band from the radio menu), AGC, STEP (tuning step of the −/+ buttons), plus enabled functions: AMP1/AMP2, ATT, NB, DNR, NOTCH, DNF, CONT (highlighted).
- The second VFO (on the right): its mode (read about every 3 s; “–” if the radio does not report it), STEP and SPLIT when working split.
Band change – a band button sets the frequency and SSB with the correct sideband: LSB below 10 MHz (160/80/40 m), USB from 10 MHz up and on 60 m. Right-click the “Band” panel to change this: “only correct the sideband when in SSB” (CW and DATA stay) or “do not change the mode”.
- − / + – tune by the selected STEP (10 Hz … 10 kHz).
- A/B – switches which VFO the radio operates on (like the radio's A/B button); the A and B frequencies stay put. The active VFO is always shown on the left as the main one – after A/B the displays swap places – and its frequency and mode go to the log, scope, spots, memories, CAT Share and remote operation; the mode buttons (LSB, USB, CW…) change the active VFO's mode. Each VFO has its own mode, which travels with its frequency. The program reads the active VFO from the radio; if the radio did not answer that read, it only tracks its own A/B button (switches made on the radio panel would then not be visible).
- A=B – copy VFO-A to VFO-B (VFO-A unchanged), e.g. before setting SPLIT.
- SPLIT – receive on VFO-A, transmit on VFO-B. With SPLIT on, VFO-A is marked RX and VFO-B TX; while transmitting, VFO-B is lit red.
- A band button sets a typical frequency of that band.
- CW and DATA – clicking again switches the sideband (CW-U ↔ CW-L, DATA-U ↔ DATA-L).
← Station profile · Home · Filter, AGC and noise reduction →
Generated from the built-in help of FT-710 Control 0.9.5-beta – do not edit here; changes go into the program (Help.swift) and tools/make_wiki.py. · Wygenerowane z pomocy programu – nie edytuj tutaj.
English
- Getting started
- Station profile
- VFO and tuning
- Filter, AGC and noise reduction
- Transmitting and safety
- RF scope and waterfall
- Display – colours and 3D mode
- Logbook, QRZ.com and map
- Online services (LoTW, QRZ, eQSL, WRL…)
- DX Cluster
- SSTV – images
- CW – decoder and sending
- Propagation
- RTTY – decoder and sending
- FT8 and FT4
- PSK31 and PSK63
- Tools: SWR sweep and who hears me
- POTA – Parks on the Air
- Alerts
- Contests – scoring and Cabrillo
- CAT Share (WSJT-X, JTDX)
- USB audio
- Remote operation
- Diagnostics
- Shortcuts
- Troubleshooting
- About
Po polsku
- Pierwsze kroki
- Profil stacji
- VFO i strojenie
- Filtr, AGC i redukcja szumów
- Nadawanie i bezpieczeństwo
- Skop RF i waterfall
- Ekran – kolory i tryb 3D
- Dziennik, QRZ.com i mapa
- Usługi online (LoTW, QRZ, eQSL, WRL…)
- DX Cluster
- SSTV – obrazy
- CW – dekoder i nadawanie
- Propagacja
- RTTY – dekoder i nadawanie
- FT8 i FT4
- PSK31 i PSK63
- Narzędzia: pomiar SWR i kto mnie słyszy
- POTA – Parki w eterze
- Alerty
- Zawody – punktacja i Cabrillo
- CAT Share (WSJT-X, JTDX)
- Audio USB
- Praca zdalna
- Diagnostyka
- Skróty
- Rozwiązywanie problemów
- O programie