Stepper_Motor_Shield_For_Arduino(DRV8825)_SKU_DRI0023

Introduction

Do you want to do some projects with stepper motors such as a drafting instrument, a 3D printer, an auto curtain, etc...? As we all know, regular stepper motors are hard to drive, but with this stepper motor shield, you can easily drive 2 stepper motors via just 6 digital I/O’s. This board is compatible with the Arduino UNO R3. Directly supports Xbee and Xbee form factor Wi-Fi, Bluetooth and RF modules. Easy connection of cables via screwless PC terminals. Each stepper motor has a code switch for adjusting driving modes, to obtain different rotational speeds. Interfaces of the board include extension 6 channel Analog I/O, 8 channel Digital I/O & I2C. Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps. The motor's position can then be commanded to move and hold at one of these steps without any feedback sensor (an open-loop controller), as long as the motor is carefully sized to the application in respect to torque and speed.

Specification

• Support 3.3V and 5V operating voltage
• Suitable for two-phase and four-wire stepper motor
• Board with two DRV8825 driver chip and a heat sink has been mounted.
• Input Voltage：8.2-45V DC (Just power the stepper motor driver), Up to 2.5A output current per coil
• Driving Pins: D4,D5,D6,D7,D8,D12
• Squeeze connector, quite easy and convenient.
• 8 channel digital I/O pins & 6 channel Analog input pins
• DRV8825 Microstepping bipolar stepper motor driver
• Six different microstep resolutions (full-step, 1/2-step, 1/4-step, 1/8-step, 1/16-step, 1/32-step)
• Compatible with Arduino UNO R3, Leonardo, Mega and other controllers, with full port extensions. Support XBee, XBee Wi-Fi, Bluetooth and RF modules, ensure that the needs of your wireless communications.
• There is a switch on the board Xbee wireless interfaces corner. PROG stop wireless module, available USB programming. RUN time can use the wireless communication module.

Pin Out& Diagram

*Wireless program switch:

• • RUN: Turn the Switch here to use the Xbee module
  • PROG: Turn the Switch here to upload the sketch via USB

*Motor wiring diagram：

• The new version expand two enable pins, you can enable/disable the motor driver to save the power consumption, Motor X enable pin for the D8, Motor Y enable pin for the D12, low voltage enable, the following truth table:

DISENABLE *Dip switch settings for Microstep resolution:

1/32 step *IO voltage select

• • Change the the position of the jumper cap according to your Main board operating voltage.

*More details

• Squeeze connector makes connection easily and quickly.
• The other form of connector for XH2.54 or female headers

Sample code

/*
This sample code is for testing the 2 stepper motors
The rotation velocity can be adjusted by the code switch
Microcontroller: Arduino UNO
*/
int M1dirpin = 7;  //Motor X direction pin
int M1steppin = 6; //Motor X step pin
int M1en=8;  //Motor X enable pin
int M2dirpin = 4;  //Motor Y direction pin
int M2steppin = 5; //Motor Y step pin
int M2en=12;  //Motor Y enable pin

void setup()
{
  pinMode(M1dirpin,OUTPUT);
  pinMode(M1steppin,OUTPUT);
  pinMode(M1en,OUTPUT);
  pinMode(M2dirpin,OUTPUT);
  pinMode(M2steppin,OUTPUT);
  pinMode(M2en,OUTPUT);

  digitalWrite(M1en,LOW);// Low Level Enable
  digitalWrite(M2en,LOW);// Low Level Enable

}
void loop()
{
    int j;
  delayMicroseconds(2);
  digitalWrite(M1dirpin,LOW);
  digitalWrite(M2dirpin,LOW);
  for(j=0;j<=5000;j++){
    digitalWrite(M1steppin,LOW);
    digitalWrite(M2steppin,LOW);
    delayMicroseconds(2);
    digitalWrite(M1steppin,HIGH); //Rising step
    digitalWrite(M2steppin,HIGH);
    delay(1);
  }
}

For any question/advice/cool idea to share, please visit DFRobot Forum.

More

• DRV8825 datasheet
• Schematic
• Historical version: Stepper Motor Shield for Arduino (A4988)

go shopping dual bipolar stepper motor shield for arduino (drv8825) (sku:dri0023)